Instructions for Use
Table Of Contents
- Table of Contents Use and care manual
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- WARNING
- Fire Safety
- WARNING
- to reduce the risk of a grease fire:
- a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
- b. Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
- c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
- d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
- WARNING
- TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A GREASE FIRE, OBSERVE THE FOLLOWING:
- a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
- b. NEVER PICK UP A FLAMING PAN – You may be burned.
- c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
- d. Use an extinguisher ONLY if:
- Cooking Safety
- Burn Prevention
- Child Safety
- Cleaning Safety
- Cookware Safety
- Proper Installation and Maintenance
- Electromagnetic interference
- Cooling fan
- Proposition 65 Warning:
- Causes of damage
- Protecting the Environment
- Cooking with Induction
- Getting familiar with the appliance
- Operation
- Main power switch
- Setting the cooktop
- Setting the element
- Selecting the heat level
- 1. Select the desired element by touching the corresponding words printed on the control panel. In the element display ‹ and the __ indicator light up.
- 2. Within the following 10 seconds, set the desired power level using the number keys.
- 3. To change the power level, select the element and set the desired power level using the number keys. To set an intermediate level touch the + symbols next to the number key 9.
- Turning off the element
- Notes
- Recommendations
- Settings table
- 9 CAUTION
- PowerBoost® function
- Cook time
- Kitchen timer
- Panel lock
- Wipe Protection
- Automatic time limitation
- Basic settings
- --------
- Changing the basic settings
- 1. Turn on the cooktop with the main switch.
- 2. Within10 seconds, touch the TIMER key for about 4 seconds.
- 3. Touching the TIMER key again takes you to the basic settings.
- 4. Touch TIMER repeatedly until the indicator for the desired function appears in the element display.
- 5. Select the desired setting using the number keys.
- 6. Touch TIMER again for 4 seconds. The setting is stored.
- Quit basic settings
- Cleaning and Maintenance
- Service
- Frequently-asked questions and answers (FAQ)
- Fixing Malfunctions
- How to Obtain Warranty Service
- STATEMENT OF LIMITED PRODUCT WARRANTY
- THERMADOR® Support
- READ AND SAVE THESE INSTRUCTIONS
- Table des Matières Notice d’utilisation
- 9 Définitions de sécuritéDéfinitions de sécurité
- CONSIGNES DE SÉCURITÉ IMPORTANTES
- LIRE ET CONSERVER CES INSTRUCTIONS
- AVERTISSEMENT
- Sécurité-incendie
- AVERTISSEMENT
- POUR RÉDUIRE LES RISQUES DE FEUX DE GRAISSE :
- a. Ne jamais faire fonctionner les unités de surface à des températures élevées sans surveillance. Des débordements causant de la fumée et des déversements graisseux peuvent prendre feu. Chauffer l'huile lentement à réglage faible ou moyen.
- b. Mettre toujours la hotte EN MARCHE pendant la cuisson à température élevée et au moment de flamber des aliments (p.ex., crêpes Suzette, cerises jubilée, steak au poivre flambé).
- c. Nettoyer souvent les ventilateurs d'aération. Il ne faut pas que la graisse s'accumule sur le ventilateur ou sur le filtre.
- d. Utiliser des casseroles de taille adéquate. Utiliser toujours des casseroles dont les dimensions conviennent à la taille de l'élément.
- AVERTISSEMENT
- POUR RÉDUIRE LE RISQUE DE LÉSIONS CORPORELLES DANS L'ÉVENTUALITÉ D'UN FEU DE GRAISSE, OBSERVER LES CONSIGNES SUIVANTES :
- a. ÉTOUFFER LES FLAMMES à l'aide d'un couvercle bien hermétique, d'une tôle à biscuits ou d'un plateau en métal, puis éteindre l'appareil. FAIRE ATTENTION À NE PAS SE BRÛLER. Si les flammes ne s'éteignent pas immédiatement, ÉVACUER LES LI...
- b. NE JAMAIS SAISIR UN RÉCIPIENT QUI BRÛLE. Vous pourriez vous brûler.
- c. NE PAS UTILISER D'EAU, y compris les chiffons ou serviettes mouillées. Une violente explosion de vapeur risque de se produire.
- d. Utiliser un extincteur uniquement si :
- Sécurité de cuisson
- Prévention des brûlures
- Sécurité des enfants
- Consignes en matière de nettoyage
- Sécurité pour la batterie de cuisine
- Installation et entretien corrects
- Perturbations électromagnétiques
- Ventilateur de refroidissement
- Avertissement issu de la proposition 65 :
- Éléments qui peuvent endommager l'appareil
- Protection de l'Environnement
- Cuisson par Induction
- Faire connaissance avec l’appareil
- Fonctionnement
- Interrupteur d'alimentation principal
- Allumage de la table de cuisson
- Réglage de l'élément
- Sélection du niveau de chaleur
- 1. Sélectionne l'élément souhaité en effleurant les mots correspondants imprimés sur le panneau de commande. Sur l'écran de l'élément, ‹ et le témoin __ s’allument.
- 2. Dans les 10 secondes qui suivent, réglez le niveau de puissance souhaité avec les touches numérotées.
- 3. Pour modifier le niveau de puissance, sélectionnez l'élément et réglez le niveau de puissance souhaité avec les touches numérotées. Pour régler un niveau intermédiaire, touchez les symboles + adjacents à la touche numérotée 9.
- Désactivation de l'élément
- Remarques
- Recommandations
- Tableau des réglages
- 9 ATTENTION
- Fonction PowerBoostMD
- Durée de cuisson
- Minuterie de cuisine
- Verrouillage du panneau
- Protection contre l'essuyage
- Durée limitée automatique
- Réglages de base
- Nettoyage et Entretien
- Entretien
- Foire aux questions (FAQ)
- Corrections des défaillances
- Comment bénéficier du service de garantie
- ÉNONCÉ DE LA GARANTIE LIMITÉE
- Soutien THERMADOR®
- Contenido Manual de instrucciones
- LIRE ET CONSERVER CES INSTRUCTIONS
- INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- LEA Y CONSERVE ESTAS INSTRUCCIONES
- ADVERTENCIA
- Seguridad para evitar incendios
- ADVERTENCIA
- PARA REDUCIR EL RIESGO DE INCENDIO OCASIONADO POR GRASA:
- a. Nunca deje las unidades de la superficie sin vigilancia a valores altos. Los derrames por hervor causan humo y salpicaduras grasosas que pueden prenderse fuego. Caliente los aceites despacio, a valores bajos o medianos.
- b. Siempre encienda la campana al cocinar a un valor de calor alto o al flambear alimentos (p. ej., Crepas Suzette, cerezas Jubilee, carne flambeada con granos de pimienta).
- c. Limpie los ventiladores extractores con frecuencia. No se debe permitir la acumulación de grasa en los ventiladores ni en los filtros.
- d. Use el tamaño adecuado de olla. Siempre use utensilios de cocina apropiados para el tamaño del elemento de la superficie.
- ADVERTENCIA
- PARA REDUCIR EL RIESGO DE LESIONES A PERSONAS EN CASO DE INCENDIO OCASIONADO POR GRASA, SIGA ESTAS INDICACIONES:
- a. SOFOQUE LAS LLAMAS con una tapa que ajuste correctamente, una placa para galletas u otra bandeja de metal, luego, apague el electrodoméstico. ASEGÚRESE DE PREVENIR LAS QUEMADURAS. Si las llamas no se apagan de inmediato, EVACUE EL ÁREA Y LLAME ...
- b. NUNCA LEVANTE UNA OLLA EN LLAMAS. Puede quemarse.
- c. NO USE AGUA, ni repasadores o toallas húmedos. Puede ocasionar una violenta explosión por vapor.
- d. Use un extinguidor sólo si:
- Seguridad al cocinar
- Prevención de quemaduras
- Seguridad de los niños
- Seguridad en la limpieza
- Seguridad en los utensilios de cocina
- Instalación y mantenimiento adecuados
- Interferencias electromagnéticas
- Ventilador de refrigeración
- Advertencia en virtud de la Proposición 65:
- Elementos que pueden dañar el electrodoméstico
- Protección Medioambiental
- Cocción por Inducción
- Para familiarizarse con la unidad
- Operación
- Interruptor de alimentación eléctrica principal
- Para encender la placa
- Ajustar el elemento
- Seleccionar el nivel de calor
- 1. Seleccionar el elemento deseado pulsando las palabras correspondientes impresas en el panel de control. En el display del elemento ‹ y la indicación visual __ se encienden.
- 2. En el término de los 10 segundos siguientes, programar el nivel de potencia deseado con las teclas numéricas.
- 3. Para cambiar el nivel de potencia, seleccionar el elemento y ajustar el nivel de potencia deseado con las teclas numéricas. Para ajustar un nivel intermedio, pulsar los símbolos + junto a la tecla numérica 9.
- Apagar el elemento
- Notas
- Recomendaciones
- Tabla de valores
- 9 ATENCION
- Función PowerBoost®
- Tiempo de cocción
- Temporizador de cocina
- Bloqueo de panel
- Protección de limpieza
- Limitación automática de tiempo
- Valores básicos
- Limpieza y Mantenimiento
- Servicio técnico
- Preguntas y respuestas frecuentes (FAQ)
- Arreglar fallas en el funcionamiento
- Cómo obtener el servicio técnico de la garantía
- DECLARACIÓN DE GARANTÍA LIMITADA DEL PRODUCTO
- Soporte técnico de THERMADOR®
- LEA Y CONSERVE ESTAS INSTRUCCIONES
14
Once the cook time has elapsed
The element turnes off once the set cook time has
elapsed. You will hear a beep. The indicator ‹ appears in
the element display and the timer display shows ‹‹ for
10seconds. The
x indicator in the element display
stays on.
Touch the TIMER key, to turn the indicators and the beep
off.
Notes
▯ To set a cooking time of under 10minutes, always
touch 0 before you select the required value.
▯ If a cooking time was set for several elements, the time
information for the selected element is shown in the
timer display.
▯ Select the relevant element to call up the remaining
cooking time.
▯ You can set a cooking time of up to ŠŠ minutes.
Automatic timer
With this function you may select a cook time for all
elements. Once an element is turned on, the selected
time will begin to count down. The element will
automatically turn off when the cook time has elapsed.
Instructions on activating the automatic timer are found in
the chapter "Basic settings".
Note: The cook time can be changed or cancelled for
any element:
Select the desired element. Touch the TIMER key. Adjust
the cook time using the number keys, or deactivate it by
setting the timer value to ‹.
Kitchen timer
The timer can be set for periods of up to 99minutes. It is
independent of the other settings. You can also use the
kitchen timer when the cooktop is turned off or locked.
This function does not automatically switch off an
element.
Setting the kitchen timer
1.
Touch the TIMER key until the V indicator lights up.
‹‹ appears on the timer display.
2.
Set the desired time using the number keys. min
appears on the timer display.
The timer start to count down after a few seconds.
Changing or deleting the time
Touch the TIMER key repeatedly until the V indicator
lights up.
Change the time using number keys, or set ‹‹ in order
to delete the programmed time.
When the time has elapsed
A beep sounds. ‹‹ appears on the timer display and the
V indicator lights up. The displays go out after
10 seconds.
Touch any key to turn off the indicators and the beep.
Panel lock
You can use the panel lock to prevent children from
accidentally turning the cooktop on.
Turning the panel lock on
The cooktop must be turned off.
Touch LOCK for 4seconds. The Ú indicator lights up for
several seconds. The cooktop is now locked.
Turning the panel lock off
Touch LOCK for 4seconds. The cooktop is now
unlocked.
9 CAUTION
The panel lock may be accidentally turned on and
off due to:
▯ water spilled during cleaning
▯ food that has overflowed
▯ objects being placed on the LOCK touch key.
Automatic panel lock
With this function, the panel lock is automatically
activated whenever you switch off the cooktop.
Turning on and off
See "Basic settings" section.
Wipe Protection
Cleaning the control panel while the cooktop is on may
change the settings. In order to avoid this the cooktop
has a wipe protection function.
To activate:
Touch the LOCK key. The Ú indicator above the key
lights up. The control panel is locked for 35 seconds.
You can now clean the surface of the control panel
without risk of changing the settings.
To deactivate:
To deactivate the function before the time has elapsed,
touch the LOCK key. The Ú indicator above the key turns
off, the function is deactivated.
Notes
▯ An acoustic signal sounds 30 seconds after activation.
This indicates that the function is about to finish.
▯ The wipe protection lock does not lock the main
switch. The cooktop can be switched off at any time.
Automatic time limitation
If the element is used for prolonged periods of time
without changes in the settings being made, the
automatic time limitation function is triggered.
The element stops heating. ”‰ and the residual heat
indicator •/œ flash alternately in the display.
The indicator goes out when any symbol is pressed. The
element can now be reset.
When the automatic time limitation is activated depends
on the selected heat level (from 1to 10hours).