Microwave Installation Instructions

ManualsBrandsThermador ManualsMicrowave OvenMT27, MBY

Page 1

Installation Instructions

for

Thermador

Microwave MBY

(Sold Separately)

Built-In Trim Kits • Models MT27 & MT30

IMPORTANT:

Local codes vary. Installation, electrical connections, circuit breakers

and grounding must comply with all applicable codes. Save these

instructions for the Local Electrical Inspector's use.

INSTALLER: Please leave these Installation Instructions with this unit for the

owner.

OWNER: Please retain these instructions for future reference.

WARNING: Disconnect power at the breaker before installing.

Please Read this entire manual before proceeding:

Ta b le of Contents

Step 1: Unpacking ............................................. 2

Step 2: Cabinet Preparation ........................... 3

Step 3: Electrical Installation ........................... 3

Step 4: Installing the Trim Kit.......................... 4

Step 5: Installing the Microwave Oven ......... 5

5 6

SENSOR

REHEAT

SENSOR

COOK

POWER

LEVEL

POP

CORN

TIMER

CLOCK

/LESS

QUICK

MIN

FUNCTION

KEY

SERVING

/WEIGHT

KEEP

WARM

TURBO

DEFROST

STOP/RESET START

Summary of content (8 pages)

PAGE 1
Installation Instructions for Thermador® Microwave MBY (Sold Separately) Built-In Trim Kits • Models MT27 & MT30 SENSOR COOK SENSOR REHEAT POWER LEVEL POP CORN 1 2 3 4 5 7 8 9 TIMER 0 CLOCK MORE /LESS QUICK MIN FUNCTION KEY SERVING /WEIGHT KEEP WARM TURBO DEFROST STOP/RESET 6 START Please Read this entire manual before proceeding: IMPORTANT: Local codes vary. Installation, electrical connections, circuit breakers and grounding must comply with all applicable codes.
PAGE 2
Step 1: Unpacking A. Microwave Oven Model MBY (Sold Separately) Open the box and carefully remove fillers and all packing material. Included with your new Thermador microwave are the following: • Care and Use manual (1) • Quick Guide (1) • Warranty Card (1) • Turn Table (1) • Turn Table Support (1) B. Trim Kit Models MT27 & MT30 Open the box and carefully remove fillers and all packing materials.
PAGE 3
Step 2: Cabinet Preparation The cabinet cut out dimensions are shown in Figure 1. • It is good practice, when microwave oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the trim and the wall/door Dimensions • Outlet should be in the shaded area as indicated in Figure 1. MT30B; MT30W; MT30S MT27B; MT27W; MT27S Height (A) 17"± 1/16 All Trim Kits Depth (C) 24"± 1/8 All Trim Kits Figure 1.
PAGE 4
Step 4: Installing the Trim Kit A. Position the 2 vertical trim brackets using the template as shown on Figure 3. Trim Brackets ➝ Screws Notch to mark the center line of the cutout. Centerline cutout ➝. #8 x 1/4 Figure 3. ➝ Template Template is used to locate the positions of the left and right trim brackets with respect to the cut out. The trims are secured with (3) screws each and the template is discarded after. Mark the center line of the cut out using the template. Screws #8 x 1/4 Figure 4.
PAGE 5
Step 5: Installing The Microwave Oven (Figure 5) Note: The four (4) ducts have a plastic covering that must be removed prior to installing these ducts onto the microwave section.These ducts have sharp edges. Be careful when handling. 1. Remove and retain outer case screw at rear of the oven (left side) 2. Position upper exhaust duct on top (Hinge Side) of oven. Fasten with outer case screw 3.
PAGE 6
Step 5: Installing The Microwave Oven (continued) 9. Remove the left side vertical trim bracket (3 screws) (for MT27 only) 10. Slide the assembled microwave oven in the prepared cabinet cutout. Plug the electrical cord in the wall receptacle (ask help from another person). Align the microwave oven legs to the pan channel holes (Figure 6). 11. Install back the left side vertical trim bracket. (3 screws) Figure 6. 12. Snap on the frame trim with the “Thermador Logo under the microwave door button.
PAGE 7
Notes Page 7
PAGE 8
Thermador reserves the right to change specifications or design without notice. Some models are certified for use in Canada. Thermador is not responsible for products which are transported from the United States for use in Canada. Check with your local Canadian distributor or dealer. Thermador, 5551 McFadden Avenue, Huntington Beach, CA 92649. For the most up to date critical installation dimensions by fax, use your fax handset and call 702/833-3600. Use code #8030.