Installation Instructions

ManualsBrandsThermador ManualsStove & Range AccessoriesThermador 48" Stainless Steel Low Backguard

English 1

Backguard & Toe Kick

Before you begin read these instructions carefully. Observe all local codes and ordinances.

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these instructions for future reference.

Backguard Installation

WARNING:

To reduce the risk of fire or injury to

persons, check to make sure all

packaging has been removed from

accessory devices before use.

WARNING:

Fingers or hands could get pinched

when installing the backguard. Severe

injury could result. Use extreme caution

and wear thick protective gloves to avoid

potential laceration to finger or hand

while sliding the backguard down onto

the range.

CAUTION:

The High Shelf can get very hot! DO

NOT place the following items on top of

the High Shelf:

• plastics or containers that can melt

• flammable items

• a total load over 30 pounds (13.6kg)

Note: If a backsplash is to be used in addition to a

backguard, install the backsplash first and the

backguard second, before sliding range into place.

AVAILABLE FOR THESE MODELS:

PRD364JDGU

Pro Grand

36" Dual Fuel Range 4 Burner Griddle

PRD364JDGC

Pro Grand

36" Dual Fuel Range 4 Burner Griddle - Canadian

PRD366JGU

Pro Grand

36" Dual Fuel Range 6 Burner

PRD366JGC

Pro Grand

36" Dual Fuel Range 6 Burner - Canadian

PRD486JDGU

Pro Grand

48" Dual Fuel Range 6 Burner Griddle

PRD486JDGC

Pro Grand

48" Dual Fuel Range 6 Burner Griddle - Canadian

PRD48JDSGU

Pro Grand

48" Dual Fuel Range w/ Steam Oven

PRD48JDSGC

Pro Grand

48" Dual Fuel Range w/ Steam Oven - Canadian

PRG366JG

Pro Grand

36" Gas Range 6 Burner

PRL366JG

Pro Grand

36" Gas Range 6 Burner - LP

PRG364JDG

Pro Grand

36" Gas Range 4 Burner Griddle

PRL364JDG

Pro Grand

36" Gas Range 4 Burner Griddle - LP

PRG486JDG

Pro Grand

48" Gas Range 6 Burner Griddle

PRL486JDG

Pro Grand

48" Gas Range 6 Burner Griddle - LP

Figure 1: High Shelf & Low Back Front View

High Shelf

Low Back

Summary of content (12 pages)

PAGE 1
Backguard & Toe Kick Installation Instructions Before you begin read these instructions carefully. Observe all local codes and ordinances. INSTALLER: Please leave these Installation Instructions with the owner. OWNER: Please retain these instructions for future reference.
PAGE 2
High Shelf Parts Included (1) High Shelf top panel (1) High Shelf front panel (13) T-20 Torx Stainless screws (16 or 14) T-20 Torx drill point screws The backguard must be attached before sliding the range into the final installed position. When there is less than a 12" (305mm) horizontal clearance between combustible surfaces ∆ and the back edge of the range above the cooking surface, a THERMADOR® Low Back or High Shelf must be purchased separately and installed.
PAGE 3
High Shelf Low Back Mounts inside side panel flange Mounts inside side panel flange Backguard Installation Flush Island Trim (Included with range) 1. Remove protective plastic. 2. Depending on model, remove the (3) or (4) T20 Torx stainless screws in the front face of the included Flush Island Trim, the (4) drill point screws securing the trim to the side panels, and the (2) or (4) drill point screws securing the piece to the back panel. Lift up to fully remove. 3.
PAGE 4
Toe Kick Panel (PA [36,48] JTKG) Toe Kick Parts Included (1) Toe Kick panel (4) T-20 Torx drill point screws 2. Remove protective plastic covering from the Toe Kick Panel. 3. Beneath the range, with the holes and flange facing up, wrap the Toe Kick Panel around the cast aluminum base. 4. The mating part has extruded dimples on both sides for which the holes of the Toe Kick Panel should seize. You should feel a definitive snap, letting you know that the part has been installed. 5.
PAGE 5
Instructions d’Installation du Dosseret et de la Plinthe Avant de commencer, lisez attentivement ces instructions. Respectez tous les codes et règlements locaux. INSTALLATEUR: Veuillez laisser ces instructions d’installation au propriétaire. PROPRIÉTAIRE: Veuillez conserver ces instructions pour consultation ultérieure.
PAGE 6
Pièces fournies avec l’étagère haute (1) Panneau supérieur (1) Panneau frontal (13) Vis Torx T-20 en inox (16 or 14) vis à pointe Torx T-20 Le dosseret doit être installé avant de remettre la cuisinière à son emplacement définitif. Lorsqu’il y a moins de 12 po (305 mm) d’espace libre horizontal entre les surfaces combustibles* et le côté arrière de la cuisinière au-dessus de la surface de cuisson, vous devez vous procurer et installer un dosseret bas ou une étagère haute THERMADORmc.
PAGE 7
Étagère haute Dosseret bas Garniture d’îlot (inclus avec la cuisinière) S’installe à l’intérieur des brides du panneau arrière S’installe à l’intérieur des brides du panneau arrière Installation du dosseret 1. Enlevez la pellicule de protection en plastique. 2.
PAGE 8
Plinthe (PA [36,48] JTKG) Pièces de la plinthe incluses (1) Plinthe (4) Vis à pointe Torx T-20 2. Enlevez la pellicule de protection en plastique qui recouvre la plinthe. 3. Sous la cuisinière, avec les trous et les brides tournés vers le haut, installez la plinthe autour de la base moulée en aluminium. 4. La pièce d’accouplement est munie de chaque côté d’encoches extrudées qui devraient s’introduire dans les trous de la plinthe.
PAGE 9
Instrucciones de instalación de la consola trasera y del rodapié Antes de empezar, lea atentamente estas instrucciones. Cumple con todos los códigos y regulaciones locales. INSTALADOR: Deje esas instrucciones de instalación al propietario. PROPIETARIO: Guarde estas instrucciones para futuras referencias.
PAGE 10
Piezas proporcionadas con el estante alto (1) Panel superior (1) Panel delantero (13) Tornillos Torx T-20 de acero inoxidable (16 or 14) Tornillos de punta Torx T20 Se debe instalar la consola trasera baja antes de empujar la estufa en su posición final. Cuando hay menos de 12 pulg. (305 mm) de espacio libre horizontal entre materiales combustibles* y el dorso de la estufa sobre su superficie, se debe comprar e instalar una consola trasera baja o un estante alto THERMADOR®.
PAGE 11
Estante alto Consola trasera baja Adorno tipo isla (incluido con la estufa) Se instala dentro de las pestañas del panel trasero Se instala dentro de las pestañas del panel trasero Instalación de la consola trasera 1. Quite la lámina de protección de plástico. 2.
PAGE 12
Rodapié (PA [36,48] JTKG) Piezas incluidas del rodapiés (1) Rodapié (4) Tornillos de punta Torx T-20 2. Quite la lámina de protección de plástico que cubre el rodapié. 3. Bajo la estufa, con los orificios y las pestañas giradas hacia arriba, instale el rodapié alrededor de la base moldada de aluminio. 4. La pieza de acoplamiento está equipada a cada lado con muescas extruidas que se deben insertar en los orificios del rodapié.