INSTALLATION INSTRUCTIONS For Built-in Refrigerators, Freezers and Wine units INSTRUCTIONS D'INSTALLATION Single Door Models Modeles A une porte Modelos de una puerta Pour r_frig6rateurs, congelateurs et caves 6 vin encastres INSTRUCCIONES DE INSTALACION s Para los refrigeradores, congeladores y unidades de vino empotrados Thermedor _ 9000222885
Contents 5 Before you Begin ........................................................................... Definitions ............................................................................... Important information 5 5 ...................................................................... 6 Installation options .......................................................................... Individual unit ............................................................................. Side-by-Side 6 6 ..
Installation instructions ...................................................................... 1. Checking the installation cavity 2.. Transoort of the appliance 3. Removing the packaging 4. Prepanng the appliance 5. Changrng 6. Prepanng the installation 7. Attaching 8. Prepanng to connect 9. Attaching .......................................................... .............................................................. ..........................................................
Before you Begin Read these instructions completely IMPORTANT Save these instructions for local inspector's use. Observe all governing codes and ordinances. Note to Installer - Be sure to leave these instructions with the Consumer. Note to ConsumerKeep these instructions Owner's Manual for future reference. and carefully. These installation instructions are intended for use by qualified installers.
Installation There are many different options installation Individual options. appliances with partition These are limited only by the design of the kitchen and the function of the finger guard. Individual unit Side-by-Side % Note When dimensioning the partition for model 4, note the thickness of the furniture fronts to prevent damage if the doors are opened at the same time. Use the Extreme Combination Side-by-Side Heating kit if the gap between the appliances less than 6" (160 mm).
Installation location r_The Do not install the appliance: side walls of the cavity must be flush. The minimum thickness must be 5/8" (16 mm). of side walls and the top wall The minimum thickness 1/2" (13 mm). of toe kick panel must be - outdoors, - in an environment with dripping water, - in rooms which are at risk of frost. A thickness of-Y4" (19 mm)is Appliance is very heavy - for empty weight see the following table: Furniture/fixtures Refrigerator Refrigerator 24" 30" recommended.
Grounding Connecting Electrical Shock the power instruction This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the electric current. Hazard - Plug into a grounded 3 prong outlet. Improper connection of the equipment grounding conductor may result in electric shock.
Installation dimensions Single installation X Y 90° 90_ iiil iii (46) 31 (25) 25/16" (59) X 133/4" (350) X Legend: A Areafor installationof the water connection B Areafor installationof the powerconnection D Openingdepthof niche,dependingon kitchendesign (seeDESIGN GUIDE) D = 24" (610 mm) minimum NOTE: Cavitymustbe suare, Sidewall of the cavitymustbe flush, Appliance 18" 24" 30" X 18" (457 mm) 24" (610 mm) 30" (762 mm) Y 9" (229 mm) 12" (305 mm) 15" (381 mm) 9
Side-by-Side Example: installation Freezer 18" / Refrigerator The cavity dimensions indicated above for the respective appliance apply to a Side-by-Side installation of two appliances. The total width of the cavity results from the addition the cavity widths indicated for the two appliances. !8 _. 30" of (1219) 30" (457) (46) iiii L 1 @ @ @ @ 0 ¸_i (457} 1i8 `¸' (457) 0 48" .
Water connection The supply pipe can be located a) at the side on the right, at the side on the left or underneath. b) c) 3%2" . 2 5/16" H _ max, 13/32 ,, (lO) (1o) 113/1" i¸¸ I 1....
Appliance 1. dimensions 18" Appliance (Freezer/Freezer with Ice and Water dispenser) 1_" e) 24" (457) b) (610) Frontview (withoutdoor panel) i15/16" (287,4) T 14_ 6" (360) b) f) 14_5" a) 797/8" 84" (2029} (2i33,6) 14_6" (36O) _ii_!_ _iiii_iiii_ : __ _ 115't6" (287,4) T 131/8" e) .... 8 (71 _7 - 106,7) 24" (510)e) 24"e_ (6io) ...... l c) (451,2) f) c) Legend: a) Adjustmentin levellinglegs+13/8" (35 mm)/ 1/2"(13 mm). b) Dimensionsmay vary. c) Thicknessof door panelmayvary.
2. 18" Appliance (Wine unit) e) b) e) 24" (81_o) 1i8¸'` (457) Frontview (withoutdoor panel) b) f) a) 797/8" 84" (2029) (2i33,6) i!iii_!_!_:i!_ii_i!!i:!;_i:il;; _¸!_i_iii !!iii 131/8" 71/8 a\ (18_) / e) (71,7 - 106,7) 24" (510)e) c) (451,2) 2o22132" ,6) c) i) c) Legend: a) Adjustmentin levellinglegs+13/8" (35 mm)/ 1/2"(13 mm). b) Dimensionsmay vary. c) Thicknessof door panelmayvary. d) This dimensionmayvary dependingon installation,panelthickness and kitchenhardware.
3. 24" Appliance (Refrigerator/Freezer/Freezer and Water dispenser) with Ice Frontview (withoutdoor panel) b) f) a) 84" (2133,61 115/16" (287,41 138 (291 e) d) c) (_91 233/4 ° (603,6) f) 2621/32" (677) c) c) Legend: Note: a) b) c) d) Onedesignof the woodenpaneldisplayed,Forfurther informationabout the differentstylescheckthe DESIGN GUIDE, Adjustmentin levellinglegs+13/8" (35 mm)/ 1/2"(13 mm). Dimensionsmay vary. Thicknessof door panelmayvary.
4. 24" Appliance (Wine unit) e) b) 24" 1/8"¸ Frontview (withoutdoor panel) i15/16" (2874) b) f) a) 797;8" 84" (2029) (213&6} (360) 115/16" (287,4) (29) e) 24 c) 3/4 ° (_9) 23%° (60&6) f) 2621/32" 90 ° 115 ° c) c) Legend: Note: a) b) c) d) Onedesignof the woodenpaneldisplayed,Forfurther informationabout the differentstylescheckthe DESIGN GUIDE, Adjustmentin levellinglegs+13/8" (35 mm)/ 1/2"(13 mm). Dimensionsmay vary. Thicknessof door panelmayvary.
5. 30" Appliance (Refrigerator/Freezer/Freezer and Water dispenser) e) 30 '_ (762) e) 24' (610) " with Ice b) _" 1/8" Frontview (withoutdoor panel) 11N6" (287,4) b) f) a) 797/8,, 84,_ (2029) (2133,6) 14_6" (360} i¸ i_ 115h 6" (287,4) i3i/8 c) c) Legend: Note: a) b) c) d) Onedesignof the woodenpaneldisplayed,Forfurther informationabout the differentstylescheckthe DESIGN GUIDE, Adjustmentin levellinglegs+13/8" (35 mm)/ 1/2"(13 mm). Dimensionsmay vary. Thicknessof door panelmayvary.
and tools Required accessories 1. Supplied - Installation - Operating - Installation 2. Cutter with adjustable accessories Metal tape measure instructions Square instructions Spirit level length 2' (60 cm) and 4' (1,2 m) kit Optional Side-by-Side Sealing For permanent connection of two individual e. g. Freezer next to Refrigerator. Combination Side-by-Side If the gap between the appliances 6" (160 mm).
Installation instructions 2.. Transport The following the installation installation instructions describe steps for various appliance types: - Refrigerator units - Freezer units - Freezer units with ice maker - Freezer units with ice-water dispenser The appliance is very heavy. Be careful, otherwise people who are helping may be injured or the appliance may be damaged.
3. Removing the packaging B (3 - The appliance unpacked. may tip over while it is being -The is very heavy. appliance -When opening the appliance may tip forwards. Preparing the appliance Remove the side brackets and fixing plates which attach the furniture fronts. To do this, loosen the fastening the stop parts. screws and remove -i-] Store the stop parts in suitable receptacles, door, the appliance otherwise they may get lost.
5. Changing over the door hinges Before working on the hinge, release the spring risk of injury[ The door hinges may have to be changed depending on the installation situation. IT]If over it is not necessary to change over the door hinges, continue with the next installation step. Q Unscrewthe door. I_ Remove the hinges. I_ Remove the parts of grill. Release the spring on the hinge. Loosen the screw from I to 0. Q Remove the hinge box covers. IT]It 2O will used new parts.
i I_ Fix the hinges on the appliance. crosswise! Change the hinges I_ Fixthe I_ Span the spring on the hinge. Tighten the screw from 0 to I. Change over the hinge angle. I_ Fit the plastic part of the grill. I_ Mount the grill completely. I_ I_ door. Change over the fixation parts on the door.
Preparing 2 anti-tip-brackets or appliance Q the installation cavity are required for each appliance combination (Side-by-Side). Specify the attachment points of the anti-tip-brackets. Specify the detailed dimensions according to the section on "Installation dimensions" starting on page 9. Assure that there are no electrical wires or plumbing in the area which the screws could penetrate - risk of injury and damage! Q Fix the hinge box cover.
Wood floor application a_ b_ C_ Use the wooden screws provided, see overview diagram "Use the screws in the screws set". Q Drill pilot holes: 1/s" (3 ram) for the (5 x 60 ram) wooden 5/G4" (2 ram) for the (4 x 15 ram) wooden screws screws Being certain the screws penetrate through the flooring and into the wall plate a minimum of 3/4" (19 mm). Q Attach the anti-tip-bracket screws hold tight. Concrete completely.
7. Attaching device an alternative anti-tip 13 Locate wall studs near the rear panel of the cavity and mark drill holes in the beam. 13 Predrill the wooden beam. 13 Attach the wooden cavity. beam to the rear panel of the If possible, always screw the wooden beam to existing studs on the rear panel of the cavity. If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be attached. However, ensure that there is no play between the appliance and the anti-tip device.
9. Attaching the edge protection 10.Side-by-Side IT]If a side-by-side installation installation is intended, now connect the two appliances together. See the Installation Manual for the Side-by-Side Q kits. To protect the corners of the installation cavity, attach the supplied protective brackets with adhesive tape. 11. Pushing the appliance into the installation IT] Caution when pushing the appliance into the installation cavity.
I_ Put the mains plug into the socket. IT]In the case of Side-by-Side appliances a separate 12. Installing and aligning the appliance socket must be used for each appliance. I_ Prevent the power cord from becoming caught. Tie a piece of string to the middle of the power cord and feed forwards under the appliance. When pushing in the appliance, pull the cable forwards. Or Using adhesive tape, stick the power cord to the floor centrally behind the appliance approx.
% Note: The height-adjustable feet at the front and rear can all be adjusted from the front. Front: with open-ended wrench Rear: with 5/16" (8 mm) hex nut driver via flexible shaft. Do not twist or jam the appliance inside the cavity! When unscrewing the height-adjustable feet, proceed gradually: Always alternate between left and right, left and right, etc.. 1/2" (SW13) The adjustment of the rear feet is facilitated appliance is unloaded at the rear.
14. Attaching the individual appliance to the side of the cavity (3 Fix the attachment plate side lugs (top) depending on the installation situation. If there is no gap or only a slight gap, it is not necessary to fix the side lugs. (3 If there is a fairly large gap above the appliance, fit a wooden beam above the appliance, ensuring that the wooden beam fits the gap exactly. (3 Screw the attachment plate lugs (side) to the adjacent furniture/fixtures (individual appliances only). 15.
16. Attaching the toe kick pane[ The maximum height of the toe kick panel is 4" from the top of the floor. Do not cover ventilation slots in the base panel. Risk of damage to the appliance. Q Remove the cap from the appliance Q Bend the water pipe according to the location of the connection on the appliance _2}. Q Push the union nut and seal onto the water pipe. Q Push the end of the water pipe into the appliance connection and screw on the union nut _3}. Tighten hand-tight.
(3 Put on the base panel (do not screw on) and measure the difference in depth Y between the base panel and toe kick panel of the adjacent furniture. (3 Remove the base panel. (3 Loosen the brackets for attaching and push in all the way. 13 Attach the base panel. [-i-] If required, the toe kick panel can be screwed to the the base panel base panel. There are screw holes in the base panel near the Velcro. 17.
18. Preparing the furniture doors When performing any work on the furniture doors, always observe the following: - Always screw into the best load-bearing of the furniture door. material - Never screw into fillers, decorative - Select a screw length which is always shorter than the thickness of the furniture front. - To prevent damage, protect surfaces of the furniture doors during installation. strips or similar.
In the case of 30" and 36" wide appliances 2 adjacent furniture doors can be attached instead of one large door. These furniture doors must be connected to 20. Attaching the adjusting to the furniture door rail a metal strip on the rear. [-i-] The adjusting means of adjusting This metal strip can be purchased from customer service as an optional accessory, see the section on "Optional accessories" on page 17.
21. Attaching and aligning the furniture IT] The double threaded door bolts are responsible for adjusting the height of the furniture front. 4x15 Q Mark this amount X on the rear of the furniture door. Q Determine door. Q Loosen the 2 nuts and remove the adjusting Q Put on the adjusting Mark the drill holes. Q Drill the holes. Q Screw on the adjusting IT] Note - Attach the adjusting rail to the furniture door with at least 6 screws.
13 Remove the furniture door. 22. Attaching IT] the furniture door Now fit the furniture handles which are screwed from behind! 13 Using the positioning aid, set both longitudinal of the furniture door parallel. 13 13 sides 13 Hang the furniture door with adjusting double threaded bolts. Using a square, extend the drill hole marks which you have just made to the vertical marks. 13 Screw the nuts a little onto the double threaded Mark and drill the holes. 13 bolts.
I_ (3 Tighten the nuts on the adjusting rail. This will fix the side alignment of the door. (3 Screw on the lower brackets (Installation Predrill holes in the furniture door! Attach the bracket: Lift the furniture door slightly away from the appliance door. Push the side bracket ((_!}.)on the left and right over the screws. - Insert the side bracket ({2}.) on the left and right into the fixing plate and slide over the screw. Slowly lower the door.
24. Attaching 1× the finger guard 2x ]]]The number of lower brackets depends on the width and the design of the furniture door. Insert the finger guard into the gap between the appliance and adjacent furniture (1.). 23. Shorten the finger guard IZI Clamp the finger guard under the brackets (2.). The finger guard mLISt cover the entire height of the door. If doors exceed the standard height, use the extra long finger guard (see "Optional accessories").
Q Attach the finger guard under the lower hinge with the angle. Slide the cover on the angle. 25. Attaching Q Place the cover strips on the door. Q Attach the light switch cover. the covers [-i-] The cover for 24", 30" and 36" appliances Q Put the vertical cover strip on the finger guard. screwed can be to the door. [-i-] The side piece of the cover strip is shorter on the side on which the finger guard has been attached.
Side-by-Side installation only: !i ¸ Q Insert the cover strip into the space between the appliances. Individual appliances Q Insert the cover strip into the space between the appliance and the wooden panel. only: 26. Aligning the ice-water dispenser (for freezer unit with ice-water dispenser only) The depth of the ice-water dispenser can be aligned inside the cutout of the furniture door.
Q Re-attach covers. 27. Attaching the shelf (for freezer Q the cover frame and unit with ice-water Insert shelf. 28. Attaching (for wine storage dispenser only) the cover strips cupboard only) Note: (19 ram) For 3/4" / 19 mm thick furniture doors: Q Slide cover frame onto the ice-water dispenser and press in until the frame is flush with the door surface. If the frame width is narrow, the cover strip side piece may have to be shortened.
29. Mounting of air separator Screw the air separator to the furniture door in order to separate the supply and waste air. \ Q Push cover strips on the longitudinal side into the gap between the furniture door and glass pane. Q Cut the cover strips on the short sides to the required length. Q Shorten the air separator Q Attach the air separator with the 2 clamps. Align the air separator with the center line of the door as illustrated in the diagram. Q Slowly close the door.
30. Adjusting angle the door opening 31. Changing the door spring To adjust the door spring: Depending on the installation situation, it may be necessary to adjust the door opening angle. A door opening angle of 115 ° has been set at the factory. To adjust the door opening angle to 90°: Q Open door to 90 ° . Rotate the adjusting screwdriver.
9000222885(8611) AIJ rights reserved. Todos los derechos reservados. Tous droits reserves. ®Thermador is a Registered Trademark of BSH Home Appliances Corporation @Thermador es una marca registrada de BSH Home Appliances Corporation @Thermador est une marque de commerce deposee de BSH Home Appliances Corporation. ThermadoW reserves the right to make changes in modeJs, features, and specifications without prior notice.
