Installation Guide
Table Of Contents
- Safety
- Advance planning
- Before you begin
- General information
- Installation considerations
- Electrical requirements
- Ductwork preparation
- Choosing the correct blower
- Attaching the hood transition
- Preparing the ceiling cutout and housing
- Custom insert installation with hood trims
- Blower motor installation
- Electrical wire connection
- EXTNCB25W 25 ft. remote and in-line blower extension cable (optional)
- Make-up air damper relay switch (optional)
- Built-in remote control accessory (optional)
- Installing grease trays and filters
- Installer checklist
- Before calling service
- Product data rating label
- Avant de commencer
- Renseignements généraux
- Facteurs à prendre en compte pour l'installation
- Exigences électriques
- Préparation du conduit d’aération
- Configurations de conduits courants
- Choix d'un ventilateur adéquat
- Assemblage du raccord
- Préparation de l'ouverture du plafond et du boîtier
- Installation encastrée sur mesure avec garnitures
- Installation du ventilateur
- Installation d'un ventilateur intégré seulement
- Acheminement des câbles
- Câble de connexion du ventilateur EXTNCB25W (optionnel)
- Commutateur à relais pour clapet d'appoint d'air (facultatif)
- Installation de la commande à distance (optionnel)
- Installation des plateaux à graisse et des filtres
- Liste de vérification à l’intention de l’installateur
- Avant d’appeler le service à la clientèle
- Plaque signalétique du produit
- Antes de comenzar
- Información general
- Requisitos instalación
- Exigencias eléctricas
- Preparación del conducto de aireación
- Configuraciones de conductos comunes
- Elección de un ventilador adecuado
- Junta de la campana
- Preparación de la abertura del techo y del armazón
- Instalación empotrada a medida con adornos
- Instalación del motor del ventilador
- Conexión de los cables
- Cable de conexión del ventilador EXTNCB25W (opcional)
- Interruptor de relé de regulador de tiro de aire de compensación (opcional)
- Instalación del mando a distancia (opcional)
- Instalación de las bandejas para la grasa y de los filtros
- Lista de chequeo para el instalador
- Antes de solicitar servicio
- Placa de señalización del producto
- Blank Page
- Blank Page
- Blank Page
3
9 IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Grounding instructions
This appliance must be grounded. In the event of an
electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current.
Be sure your appliance is properly installed and grounded
by a qualified technician. Installation, electrical
connections and grounding must comply with all
applicable codes.
If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
WARNING
To reduce the risk of fire or electric shock, DO NOT use
this appliance with any solid-state speed control devices.
Safety codes and standards
This appliance complies with one or more of the following
Standards:
• UL 507, The Standard for the Safety of Electric Fans
• CSA C22.2 No. 113, Fans and Ventilators
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
CAUTION
Unit is heavy and requires at least two people
or proper equipment to move and install.
Hidden surfaces may have sharp edges. Use
caution when handling the appliance. Failure
to do so may result in property damage or
personal injury.
Never modify or alter the construction of the appliance.
For example, do not remove panels, wire covers or
brackets/screws.
CAUTION
For general ventilating use only. DO NOT use to exhaust
hazardous or explosive materials and vapors. To reduce
the risk of fire, use only metal ductwork.
Remove all tape and packaging before using the
appliance. Dispose of packaging in an environmentally-
responsible manner. Never allow children to play with
packaging material.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
• Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable
codes and standards, including fire-rated
construction.
• Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow
the heating equipment manufacturer's guideline and
safety standards such as those published by the
National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code
authorities.
• When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
• Ducted fans must always be vented to the outdoors.
• USE ONLY METAL DUCTWORK.
• DO NOT vent exhaust air in spaces with walls or
ceilings or into attics, crawl spaces or garages.
CAUTION
An outside fan is to be mounted behind louvers or in a
location where the entrance of drawn in water is unlikely.
Proposition 65 Warning
This product may contain a chemical known to the State of
California, which can cause cancer or reproductive harm.
Therefore, the packaging of your product may bear the
following label as required by California:
State of California Proposition 65 Warning:
: WARNING
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov