The Ideal Home Entertainment Center C 2006 Thermaltake Technology Co., Ltd. All Rights Reserved. All other registered trademarks belong to their respective companies.
CContents ontents C hapter 1. Product Introduction 1.1 Specification C hapter 01 2. Case Mechaniacl Operation 2.1 How to open the side panel 03 2.2 5.25"device installation 04 2.3 3.5" device installation 06 2.4 Tool-free PCI slot Usage 08 2.5 Power Supply Unit Installation 09 C hapter 3. Motherboard & Leads Installation 3.1 Motherboard Installation 11 3.2 Case LED Connection 13 3.3 Case Open Alarm Connection 13 3.4 USB 2.0 & IEEE 1394 Firewire Connection 14 3.
Chapter 1. Product Introduction 1.
Chapter 2. Case Mechaniacl Operation 2.2 5.25"device installation 2.1 How to open the side panel 1 1 Firstly, please release the thumb screws of HDD cage shown as picture. Please find the side panel key in the back of the chassis, then unlock it as shown. Push down and hold the metal tab then pull the cage out-ward to remove from chassis. 2 2 Make sure the side panel lock is opened, push the button then swing out the side panel. 03 Remove the screws on the both side of 5.25"cage.
2.3 3.5" device installation 3 1 Unscrew the screws on the both side of 5.25"cage. Remove the 5.25" cover. 2 Remove the 3.5" bay cover if you would like to install Floppy Disk Drive. (If no, please see the step 5) 4 3 Insert the device into the desired location of 5.25" drive bay then slide it along the fixed-positioning rack inside the cage. Insert Floppy Disk Drive into the cage 5 4 Secure FDD with screws from the both side of the cage labeled "FDD".
2.4 Tool-free PCI slot Usage 5 1 Insert hard drive disk into the desired location of cage Squeeze and pull out-ward the tool-free clip securing the PCI bracket. 6 2 Take off the PCI bracket. Secure hard drive disk with enclosed screws from the both side of the cage. 3 7 Locate the graphic card to the motherboard through fixing it on the space of PCI bracket and insert it to the PCI slot. 4 Install back the HDD cage. Push back the clip to secure the graphic card.
Chapter3 Motherboard & Leads Installation 2.5 Power Supply Unit Installation Important Notice Contents below are additional information for proper motherboard installation for Thermaltake Chassis. 1 Please find out the mylars types from the accessory box (clear plastic films) Install power supply unit as shown picture *Note: Due to the unique design of the Chassis, these Mylar tapes are included to prevent ATX motherboards from contacting the chassis.
3.1 Motherboard Installation How to open the front panel Each motherboard has different standoff layout. It is highly suggested that you refer to your motherboard's manual when installing motherboard into the Case. The cases are applicable with Standard ATX and Micro ATX motherboards. Your motherboard may require a special I/O Panel, which should be included with your motherboard.
3.2 Case LED Connection 3.4 USB 2.0 & IEEE 1394 Firewire Connection On the front of the case, you can find some LEDs and switch leads (POWER SW*1, POWER LED*1, H.D.D. LED*1, RESET SW*1) Please consult user manual of your motherboard manufacturer, then connect these leads to the panel header on the motherboard. These leads are usually labeled; if not, please trace them back to the case front to find out their source.
3.5 Audio Connection Please check your motherboard ,does it support AC'97 or HD-Audio , choose one of them to connect. IEEE1394 Firewire connection Please consult your motherboard manual to find out the section of "IEEE1394 Firewire connection".
3.6 eSATA connection Chapter4 Other 4.1 Media LAB (VFD display) Installation (Optional) 1 Please remove the front panel (See "how to open the front panel" ) Connect this to your motherboard at the "HDD LED". arrow means "+" 2 Remove the 4 screws from 5.25" Media LAB Connect this to your power supply unit 3 Connect this to your motherboard at SATA. Screw on the core of the Media LAB onto the designated VFD Window location.
4.2 7"LCD monitor Installation (Optional) 1 4 Please connect the Power SW connector to the PWR_SW connectors on the VFD core as shown. Unscrew the both side screws of 7" drive bay cover. 5 2 Installation complete, please reinstall the front panel and the chassis casing of the Mozart TX chassis Pull out the both side clips then remove the cage one the 7"drive bay monitor.
3 5 Insert the 7"device Install the 7" cage onto the 7" drive bay 6 4 Install the frame. Push all the metal clips to fix the cage.
Secondary System Mini ITX Installation(Optional) 4.3 Secondary System Mini ITX Installation (Optional) This mini ITX upgrade kit (optional) includes following items 1 This side towards the rear of the chassis. 5.25" PSU -270W (Please install to 5.25" drive bay) 2 The circles mean the screw holes of mini ITX IDE data cable x 1 SATA data cable x 1 3 23 Power on/off and Reset switch (please install to 5.
