TANKLESS GAS WATER HEATER Owner’s Guide Model : NER66OD (GQ-2039WS ET US) FOR USE IN RESIDENTIAL OR MANUFACTURED HOME APPLICATIONS. WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. - WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance.
Important Safety Information-1 To prevent damage to property and injury to the user, the icons shown below will be used to warn of varying levels of danger. Every indication is critical to the safe operation of the water heater and must be understood and observed. Potential dangers from accidents during installation and use are divided into the following four categories. Closely observe these warnings; they are critical to your safety. Icons warning of risk level This is the safety alert symbol.
Do not allow anyone to change the water temperature while hot water is being used. Do Not Install Indoors. Prohibited This will cause carbon monoxide poisoning and a potential fire hazard. Prohibited Indoor To prevent scalding, do not change the water temperature to a higher setting. WARNING No flame. Be sure to do. Be sure to do. A. This water heater does not have a pilot. It is equipped with an ignition device that automatically lights the burner. Do not try to light the burner by hand. B.
Important Safety Information-2 (Continued) WARNING Prohibited Do not place combustibles such as laundry, newspapers, oils etc. near the heater or the exhaust vent terminal. Prohibited Do not use hair spray or spray detergent in the vicinity of the heater. Prohibited Do not allow small children to play unsupervised in the bathroom. Do not allow small children to bath unsupervised. Unit Prohibited Carbon Monoxide Poisoning Hazard.
CAUTION Be sure to electrically ground the unit. Do not turn off the water heater while someone is bathing. Prohibited Ground. Keep power cord free of dust. Prohibited Be sure to do. Prohibited Prohibited Be sure to do. Do not use the water heater for other than hot water supply, shower and bath. Do not use a broken or modified power cord. Do not bind, bend or stretch power cords. Do not scratch, modify, or subject them to impact or force. Prohibited Don’t touch.
Important Safety Information-3 CAUTION Do not drink water that has been inside the unit for an extended period of time. Do not drink the first use of hot water from the unit in the morning. Clean the filter on the water inlet as frequently as required by the quality of your local water. Keep the area around the unit clean. If boxes, weeds, cobwebs, cockroaches etc. are in the vicinity of the unit, damage or fire can result. For installations at higher elevations, contact Noritz America for Instructions.
Contents Important Safety Information........................................................................ 2 Contents......................................................................................................... 7 Unit Components........................................................................................... 8 Display Window.............................................................................................. 9 Initial Operation...............................................
Unit Components Unit Outdoor Wall Mounted, Power Vented Model Exhaust Vent Front Cover Display Window Water Drain Valve (with Water Filter) (Inside Water Inlet) (page 22) Pressure Relief Valve Water Supply Valve Gas Supply Valve * The above illustration shows an example of installation. The exact installation configuration may be slightly different. 8 Displayed during power "ON" or combustion. (page 9) Two or three digitnumber is displayed when a failure occurs.
Display Window The display window allows you to view the status of unit or error codes. (Display Window) When the gas burner is on. On When the gas burner is on, set temperature's is displayed for one minute. When unit is initially plugged into power, set temperature's is displayed for approx. three minutes. When hot water flows. (When the gas burner is off, and cold water flows.
Initial Operation Before the first use of your water heater, do the following: Please check the following when you use the water heater for the first time after the installation. Usually, the hot water is supplied by opening the hot water if gas, water, and electric power are supplied (if there is a remote controller, it should be turned ON). Follow steps 1 through 4. 1 CLOSED 2 Open a hot water fixture to confirm that water is available, and then close the fixture again. Open the water supply valve.
How to Use (Not using the remote controller) Using the Water Heater The factory temperature setting is 120°F. Mix with cold water with a mixing valve or at the fixture for desired temperature. (Display Window) Set temperature is displayed. * When unit is initially plugged into power. Check that electrical power is connected. * How to check the set temperature. If the power supply is set to "OFF", (Display Window) and then set to "ON", the temperature of supplied hot water is displayed.
How to Use (Using the optional remote controller) Remote Controller Optional Remote Controller (RC-7651M) If you want to change the temperature of supplied hot water frequently or you want to set the amount of hot water to accumulate the hot water, this remote controller is useful. What is actually displayed depends on how the water heater is set. Burner On Indicator Setting Buttons When burning, the indicator is lit.
How to Use (Using the optional remote controller) Setting and Using the Water Heater Press the Power On/ Off Button. On On The temperature will be displayed on the remote control thermostat. Set temperature. Previous set temperature (Ex.: 115°F) Check the indicator lights. (Always check the temperature setting before use. ) Hot Cold Water temperature ( When using °F mode: temperature settings below are examples.
How to Use (Using the optional remote controller) Adjusting the Maximum Output Temperature Turn off the Power On/Off Button. Press and hold the flow meter alarm set button until a sound is heard (2 sec.). Change the temperature using the setting buttons. Off Tone sounds after 2 sec. Up Down The upper limit of the hot-water supply temperature can be changed to (For Fahrenheit (°F)) 115°F, 120°F, 125°F, 130°F, 135°F or 140°F. (For Celsius (°C)) 46°C, 47°C, 48°C, 50°C, 55°C or 60°C.
DANGER To prevent scalding: High Temperature Hot Water Heater temperatures over 125°F (52°C) can cause severe burns instantly or death from scalding. • Children, disabled and elderly are at the highest risk of being scalded. Feel water temperature before bathing or showering. Temperature limiting valves are available, ask professional person.
How to Use (Using the optional remote controller) Flow Meter Alarm Preparation Plug the bath drain. (Starting with the power off) Press the Power On/Off Button. On The temperature will be displayed on the remote control thermostat. Set temperature. When the display setting is in Fahrenheit. On When the display setting is in Celsius. On Previous set temperature (example:115°F) Previous set temperature (example:46°C) Check the indicator lights. Check the indicator lights.
An alarm will sound for ten seconds when the flow reaches the set level. High Temperature. Check the temperature before stepping into the bath tub. The water will continue to run unless it is manually turned off. If the flow meter alarm is being used to indicate when a tub is full: • If any hot water is being used besides what is going into the tub, the alarm will sound before the tub is full.
How to Use (Using the optional remote controller) Muting the Remote Controller The remote controller will emit a sound when any button is pushed. This sound can be muted if it is desired. * Initial factory setting is with sound Hold the Power On/ Off Button for five seconds. Muted No sound after 5 sec. Sound Tone sounds after 5 sec. • The flow meter alarm cannot be muted. • The high temperature warning tone when setting the unit to 125°F / 55°C (131°F) or higher will not emit a sound when muted.
Preventing Damage from Freezing-1 CAUTION * Damage can occur from frozen water within the device and pipes even in warm environments. Be sure to read below for appropriate measures. * Repairs for damage caused by freezing are not covered by the warranty. Freezing is prevented within the device automatically by the freeze-prevention heater. Freezing cannot be prevented when the power plug is unplugged. Do not remove the power plug from the wall outlet.
Preventing Damage from Freezing-2 If the water heater will not be used for a long period of time, drain the water. Drain the water as follows: CAUTION High Temperature To avoid burns, wait until the unit cools down before draining the water. The appliance will remain hot after it is turned off. Drain water into a bucket to prevent water damage. 1. Close the gas valve. 2. Fully open one of the hot water fixtures.
Regular Maintenance-1 Periodic Inspection CAUTION Be sure to do. To prevent burns or scalding, turn off the power button or power supply and wait until the unit cools before performing maintenance. Check For laundry, newspaper, timber, oil, spray cans and other combustible materials near the heater or the exhaust vent. Check For abnormal sounds during operation. Check For dust and soot in the exhaust vent. Check For dust or debris in the air inlet.
Regular Maintenance-2 Periodic Maintenance Water Drain Valve (with Water Filter) If the water drain valve (with water filter) is covered with debris, the hot water may not run smoothly, or the unit may put out cold water. Check and clean the filter as explained below. * To avoid burns, wait until the unit cools down before draining the water. The appliance will remain hot after it is turned off. 1. Close the water supply valve. 2. Open all hot water fixtures. 3.
Water Quality and Maintenance For people who live in a hard water area, periodical flushing is necessary. If the Heat Exchanger is not flushed, the Scale Build-up may cause damage to the Heat Exchanger. In this case, this water heater will detect the Scale Build-up in the Heat Exchanger and then the error code " "* will be displayed in the Display Window. When the error code " "* is flashing in the Display Window, the Heat Exchanger needs to be flushed to prevent damage from Scale Build-up.
Troubleshooting-1 Check for an Error Code on the Display Window or Optional Remote Controller Flashing If there is a problem with the unit, a numerical error code will flash on the display window or optional remote controller. If this occurs, take appropriate measures as listed below. When an error code appears, the display and the operation light will flash together.
Initial Operation Problems What to do Display Window Unit does not attempt to Check for reversed plumbing? ignite when water is running. Check the water drain valve filter. (page 22) Reset unit and try again. There may be air in the gas line. Unit attempts to ignite but fails. Have a professional check the gas supply pressure. The water may be mixed in the hot water plumbing. The hot water is not the correct temperature. The actual outlet water temperature is lower than the set temperature of the unit.
Troubleshooting-2 Temperature Problems What to do The hot water at the fixture is too hot. Are the gas and water supply valves fully open? [Using the optional remote controller] Is the water temperature setting appropriate? (page 13) [Using the optional remote controller] If the water supply temperature is high, it is possible for the outlet temperature to be higher than the temperature set on the remote controller. The hot water at the fixture is not hot enough.
w Amount of Hot Water Problems What to do The amount of hot water at a certain fixture is not constant. When hot water is demanded at other fixtures, the amount available may be reduced. The maximum flow available from this unit is 5.3 GPM (20L/min.) at a 45°F (25°C) temperature rise. Display Window Pressure fluctuations and other plumbing conditions can cause the temperature and pressure at a fixture to be unstable, but it should stabilize after a short time.
Troubleshooting-3 Sounds Problems What to do Display Window The fan can be heard after These noises indicate the proper operation of devices operation is stopped. which are designed to let the unit reignite more A motor can be heard when turning quickly, and ensure the water temperature is stable. the unit ON or OFF, when opening or closing a fixture, or after the unit has been running for a while. The fan can be heard when The fan may run to prevent freezing. it is very cold outside.
w ow Follow-up Service-1 Requesting Service First follow the instructions in the troubleshooting section (pages 24 - 28). If the error is not corrected, contact Noritz America Technical Support at 866-766-7489 or http://support.noritz.com/. We will need to know: The Model ..................(check the rating plate) *See page 4 for the location of the label Date of purchase.......(see the warranty) Details of problem.....(flashing error codes, etc.
Follow-up Service-2 Gas Conversion If you move to a region that uses a different type of gas or if the local gas supply is converted, replacement of the gas manifold and adjustment of the appliance will be necessary. This work must be performed by either Noritz or a qualified service agency and will be charged for even during the warranty period. The qualified installer will also be responsible for purchasing the gas conversion kit directly from the manufacturer.
Specifications • Specifications may be changed without prior notice. • The capacity may differ slightly, depending on the water pressure, water supply, piping conditions, and water temperature. Specifications Specification Item Model Name Type NER66OD (GQ-2039WS ET US) Outdoor Wall Mounted Power Vented Direct Ignition 15-150 psi 0.5 GPM (2 L/min.) 20.5" (520mm) x 13.8" (350mm) x 6.
Noritz America Corporation LIMITED WARRANTY - TANKLESS WATER HEATERS 1. What is Covered by this Warranty During the applicable Warranty Period (specified below), Noritz America Corporation (“Noritz“) warrants to the original purchaser (“Buyer”) that the new Noritz gas water heater in the originally installed location (“Product”) is free from material defects in material or workmanship (the “Warranty”).
