Installation Guide

ManualsBrandsThermaSol ManualsShop All ThermaSolThermaSol Rhombus 17" x 12-1/2" Frameless Bathroom Mirror – with Anti-Fog Technology

81161 1 OF 6 REV B 01/15 JWJ

Headquarters & Technical Support

1958 Steam Way, Round Rock, TX 78665 – (800) 776-0711

Mon – Fri 7:00 – 7:00 CST

www.thermasol.com

Fog-Free Mirrors

Installation Instructions

Please read and follow the instructions completely before beginning installation.

WARNING: All work must be done to National and Local Electrical codes.

Rhombus Eclipse Avant Cupola

12.5” x 17” 14.25” x 22” 12.5” x 22” 12.5” x 22”

Fog-Free Mirror

(Mirror weight 8 lbs. (3.6 kg))

Parts Enclosed:

 Assembled mirror with heating pad

 Transformer wiring: 120V Input (black-white), 12V Output (red-blue)

 2 – Solder-less connectors

Materials needed:

 18 gauge wire

 Clear silicone

 Drill

 1 - ¼” drill bit

 1 – 5/8”drill bit

 2 - # 10 self-tapping screws

 2 - # 10 anchors

Summary of content (6 pages)

PAGE 1
Headquarters & Technical Support 1958 Steam Way, Round Rock, TX 78665 – (800) 776-0711 Mon – Fri 7:00 – 7:00 CST www.thermasol.com Fog-Free Mirrors Installation Instructions Please read and follow the instructions completely before beginning installation. WARNING: All work must be done to National and Local Electrical codes. Rhombus Eclipse Avant Cupola 12.5” x 17” 14.25” x 22” 12.5” x 22” 12.5” x 22” Fog-Free Mirror (Mirror weight 8 lbs. (3.
PAGE 2
IMPORTANT INSTRUCTIONS WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: 1) READ ALL INSTRUCTION BEFORE INSTALLING AND USING THIS MIRROR. 2) THIS HEATER IS HOT WHEN IN USE. TO AVOID BURNS, DO NOT LET BARE SKIN TOUCH HOT SURFACES. 3) EXTREME CAUTION IS NECESSARY WHEN ANY HEATER IS USED BY OR NEAR CHILDREN OR INVALIDS AND WHENEVER THE HEATER IS LEFT OPERATING AND UNATTENDED.
PAGE 3
INSTALLATION INSTRUCTIONS WARNING: Must be wired, connected and all work must be done to National and Local Electrical codes. 1. Drill two 1/4” Dia. Holes 9-11/16” apart at a desired height on wall. Refer to figure #1. Insert PLASTIC anchors to reinforce holes. Use two 1-1/2” - #10 pan head screws for mounting the mirror. Screw the flat head screws into the anchors leaving ¼” protruding.
PAGE 4
WARNING: Make sure there is no insulation or combustible material within 8 inches of The transformer. NO material should touch the transformer. Figure #2  Use the proper Crimping tool for solderless connectors: WT1455, WT2000, WT105M, ERG-2001, ERG-2003. Figure #3 4. You will need to supply 18-gauge wire to connect and extend blue and red transformer wires. Pull the wires through the hole, leaving roughly 1.5 feet extra out from wall for maneuverability and ease of installation. 5.
PAGE 5
OPERATION 1. BEFORE USE ENSURE THE MIRROR IS INSTALLED PER THE INSTRUCTION MANUAL. 2. IF THESE STEPS ARE FOLLOWED, YOUR FOG-FREE MIRROR WILL BE A PLEASURE TO LOOK AT AND USE FOR MANY YEARS. 3. TRANSFORMER IS MOUNTED IN REMOTE LOCATION AND IS TURNED ON AND OFF WITH A SWITCH LOCATED OUTSIDE THE SHOWER AREA. 4. TRANSFORMER IS INSTALLED TO ENSURE THE SAFETY OF THE USER. DO NOT TAMPER WITH. 5. YOUR MIRROR MAY REQUIRE PERIODIC CLEANING WHEN DIRTY. 6.
PAGE 6
MAINTENANCE 1. YOUR MIRROR MAY REQUIRE PERIODIC CLEANING WHEN DIRTY. 2. MAKE SURE BREAKER IS OFF AND MIRROR IS COOL TO THE TOUCH PRIOR TO ANY CLEANING/SERVICE. 3. IF THESE STEPS ARE FOLLOWED, YOUR FOG-FREE MIRROR WILL BE A PLEASURE TO LOOK AT AND USE FOR MANY YEARS. 4. USE A GLASS CLEANING SOLUTION SUCH AS “WINDEX” AND A SOFT CLEAN COTTON CLOTH TO CLEAN THE MIRROR. NEVER USE ANY SURFACE CLEANERS THAT DO NOT APPLY TO GLASS SURFACES. 5.