Instruction Manual

ManualsBrandsTHERMON ManualsFiltersTHERMON G10 M-10 Series FLO-DRI Filters

Part No. 10298.Rev.4.02 March 2022 Printed in Canada

ISO 9001

CRN# 0E09312.2C

G-10& M-10 Series

FLO-DRI Filters

Installation, Maintenance Instructions, & Parts List

Special Notes

The following special notices highlight important

information in the installation, operation and

maintenance sections.

This symbol indicates a potentially hazardous

situation, which, if not avoided, can result in

personal injury or damage to the equipment.

This symbol indicates a potentially hazardous

situation, which, if not avoided, may be a shock

hazard.

This symbol indicates an imminently hazardous

situation, which, if not avoided, could result in

death or serious injury.

CAUTION

WARNING

WARNING. Improper installation

adjustment, alteration, excessive vibration,

service, or maintenance can cause property

damage, injury or death. Read the

installation, operating and maintenance

instructions thoroughly before installing,

operating or servicing this equipment.

Summary of content (8 pages)

PAGE 1
ISO 9001 FLO-DRI Filters G-10& M-10 Series Installation, Maintenance Instructions, & Parts List WARNING WARNING. Improper installation adjustment, alteration, excessive vibration, service, or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing, operating or servicing this equipment.
PAGE 2
TABLE OF CONTENTS A. Filter Maintenance Instructions 3 B. To Change FLO-DRI Cartridges 3 C. FLO-DRI filter installation instructions 4 D. Cartridge Media 4 D.1 Natural Gas ............................................................................................................................................4 D.2 Compresssed Air Cartridge Media.......................................................................................4 E. Parts List 5 F. Change-out Schedule for FLO-DRI 6 G.
PAGE 3
A. FILTER MAINTENANCE INSTRUCTIONS 1. The following simple maintenance procedures will ensure maximum FLO-DRI filtering efficiency and a longer filter life. 2. FLO-DRI cartridges should be examined frequently until a pattern of usage is established. 3. Failure to replace cartridges in an expedient fashion may result in excessive pressure drop and the possibility of contaminant carry over.
PAGE 4
C. FLO-DRI FILTER INSTALLATION INSTRUCTIONS 1. For maximum efficiency, FLO-DRI unit should be installed as indicated in Figure 1. 2. Install in a vertical position only. 3. Tighten fittings into casting 5.5 to 6.0 turns. Do not over-tighten threaded connections. This may lead to thread damage or possible cracking of the casting. 4. Ensure flow direction is as indicated on the unit. 5. Installation of drain leg is highly recommended. 4.5" 114.
PAGE 5
E. PARTS LIST Table 2 – G-10 & M-10 Parts List C Item No. Req. Part No. A 1 End cap B 1 Body C 3 Castle nut D 3 Stud E 1 F 1 G 1 10256 O-ring, End cap, 10 Series H 1 10257 Perforated disc, 10 Series, Concave 10255 Description D A G Spring, 10 Series, SST Drain cock, Assembly, 1/8 NPT E Table 3 – Replacement FLODRI-MTG10 No. Req. Part No.
PAGE 6
CHANGE-OUT SCHEDULE FOR FLO-DRI F. Table 5, page 6 shows cartridge change-out frequencies in days for each model heater and gas scrubber for H2S and moisture. To determine the cartridge change-out frequency in days for other H2S moisture concentrations, use the formulas provided in the examples.
PAGE 7
NOTES
PAGE 8
PLEASE ADHERE TO INSTRUCTIONS IN THIS MANUAL Failure to do so may be dangerous and may void certain provisions of your warranty. For further assistance, please call 24hr hotline: 1-800-410-3131 (U.S.A. and Canada) Please have model and serial numbers available before calling.