User Guide

ManualsBrandsThermos ManualsFood StorageStainless King 24 oz. Vacuum Insulated Stainless Steel Drink Bottle

VACUUM INSULATED STAINLESS STEEL DIRECT DRINK BOTTLE

GENERAL CARE

• Before first use, wash all parts with warm, soapy water. Rinse all parts thoroughly and

allow time to dry.

• Contents should not be left in the container for longer than 24 hours. As soon as

possible after each and every use, wash all parts with warm, soapy water. Rinse all

parts thoroughly with clean water. Allow all parts to dry completely prior to next use

or storage

• DO NOT use abrasive cleaners or scrubbers since they may dull the finish.

• DO NOT use bleach or cleaners containing chlorine on any parts of the product.

• This product is top-rack dishwasher safe; however, hand washing is recommended as

the dishwasher uses harsher detergents and hot water that may affect the appearance

of your product.

• Residual liquids, foods, or other contents may become trapped between product

components, such as lid parts, container parts, gaskets (flexible band around lid

and/or stopper), or straws (if present in the product). Although this product is top-rack

dishwasher safe, hand washing is recommended to ensure that all parts of the product

are thoroughly cleaned.

ASSEMBLY & USE

Direct Drink Lid with Lock Ring (If present):

CARE AND USE GUIDE

Summary of content (5 pages)

PAGE 1
C CARE AND USE GUIDE VACUUM INSULATED STAINLESS STEEL DIRECT DRINK BOTTLE GENERAL CARE • Before first use, wash all parts with warm, soapy water. Rinse all parts thoroughly and allow time to dry. • Contents should not be left in the container for longer than 24 hours. As soon as possible after each and every use, wash all parts with warm, soapy water. Rinse all parts thoroughly with clean water.
PAGE 2
Image for reference only: actual product may vary 1. Remove lid (A) by twisting counterclockwise. 2. Pull down the locking ring (C1) located on the lid (A). Press the push-button (C) on the lid (A) to open lid cover (B). 3. Remove o-ring gasket (A1) from underside of lid (A). 4. Remove lid cover gasket (B1) from lid cover (B). 5. Wash all parts separately, then re-assemble. a. Ensure both gaskets (A1 and B1) are properly seated to minimize leaking. 6. Fill container with contents.
PAGE 3
6. Hold the tea infuser (E) upright and gently push the tea infuser into the o-ring (A1) on the lid (A). 7. Fill container with hot water up to the desired height. If the tea infuser (E) is not fully submerged in water, close and lock the product and tip product to infuse from any angle. Do not overfill: Leave space for the lid (A) and the rest of the tea infuser (E), to avoid overflow. 8. For best tea brewing results, follow the instructions provided by the manufacturer of your tea. 9.
PAGE 4
7. Fill container with contents. Do not overfill: Leave space for the lid (F), to avoid overflow. 8. Replace the lid (F) by twisting it clockwise. 9. To drink, push the button (G) located on the lid (F) of the bottle, which will release the lid cover (H) and reveal the drink opening. 10. When finished drinking, close and lock the lid cover (H) and lock the product by switching the slide lock (G1) to the “locked” position.
PAGE 5
Some jurisdictions do not allow the exclusion of incidental, consequential or special damages, so the preceding exclusion may not apply to you. This is a factory guarantee. Please do not return this product to the retailer. Send defective unit or component along with written explanation of defect directly to: Thermos L.L.C. - Warranty Service 355 Thermos Road Batesville, MS 38606, USA 1-800-831-9242 www.thermos.com In Canada: 1-800-669-7065 www.thermosbrand.