Use and Care Manual

ManualsBrandsThermos ManualsSports & OutdoorsGuardian 24 oz. Rosewood Red Hard Tritan Plastic Vacuum-Insulated Water Bottle

HYDRATION BOTTLES

GENERAL CARE

 Before first use, wash all parts with warm, soapy water. Rinse all parts thoroughly and allow time

to dry.

 Contents should not be left in the container for longer than 24 hours. As soon as possible after

each and every use, wash all parts with warm, soapy water. Rinse all parts thoroughly with clean

water. Allow all parts to dry completely prior to next use or storage

 DO NOT use abrasive cleaners or scrubbers since they may dull the finish.

 DO NOT use bleach or cleaners containing chlorine on any parts of the product.

 This product is top-rack dishwasher safe; however, hand washing is recommended as the

dishwasher uses harsher detergents and hot water that may affect the appearance of your

product.

 Residual liquids, foods, or other contents may become trapped between product components,

such as lid parts, container parts, gaskets (flexible band around lid and/or stopper), or straws (if

present in the product). Although this product is top-rack dishwasher safe, hand washing is

recommended to ensure that all parts of the product are thoroughly cleaned.

ASSEMBLY & USE

Hard Spout Lid with Push Button and Slide Lock:

1. Remove lid (A) by twisting counterclockwise.

2. Unlock the slide lock (B) by sliding the lever to the “unlocked” position. Press the push-button (C)

on the lid (A) to open lid cover (D).

3. Pull out O-ring gasket (A1) from underside of lid (A) and spout gasket (D1) from underside of lid

cover (D).

4. Wash all parts separately and re-assemble. a. Ensure gaskets are properly seated to minimize

leaking.

5. Fill container with contents. Do not overfill: Leave space for lid (A) to avoid overflow.

6. Replace the lid (A) by twisting it clockwise.

7. To drink, Unlock the slide lock (B) by sliding the lever to the “unlocked” position. Push the button

8. When finished drinking, close and lock the lid cover (D) by pushing the lid cover firmly down and

lock the product by switching the slide lock (B) to the “locked” position.

9. The rotating intake meter (F) (if present) can be used to manually track how many bottles of liquid

that are consumed. To use the intake meter, manually rotate the meter to the number “1” position

as shown and after each bottle of liquid is consumed, rotate the meter counterclockwise to the next

higher number to track your consumption.

CARE AND USE GUIDE

Summary of content (4 pages)

PAGE 1
C CARE AND USE GUIDE HYDRATION BOTTLES GENERAL CARE  Before first use, wash all parts with warm, soapy water. Rinse all parts thoroughly and allow time to dry.  Contents should not be left in the container for longer than 24 hours. As soon as possible after each and every use, wash all parts with warm, soapy water. Rinse all parts thoroughly with clean water. Allow all parts to dry completely prior to next use or storage  DO NOT use abrasive cleaners or scrubbers since they may dull the finish.
PAGE 2
Image for reference only. Actual product may vary. Hard Spout Lid with Twist Drink Spout Cover: 1. Remove lid (A) by twisting counterclockwise. 2. Unlock the drinking spout cover (B) by twisting spout cover counterclockwise until the cover fully stops twisting (about 1/4 turn). Pull up on spout cover to open and expose drinking spout (C). 3. Pull out O-ring gasket (A1) from underside of lid (A) and spout cover gasket (B1) from underside of spout cover (B). 4. Wash all parts separately and re-assemble. a.
PAGE 3
5. Wash all parts separately and re-assemble. a. Ensure gaskets are properly seated to minimize leaking. 6. Fill container with contents. Do not overfill: Leave space for the lid (A) and straw stem (D), to avoid overflow. 7. Replace lid (A) by twisting clockwise. 8. To drink, pull on the straw tab (B1) on the sipper straw (B) to open. 9. When finished drinking, press the sipper straw (B) down to closed position. 10.
PAGE 4
      Check periodically to make sure any gasket (flexible band around lid and/or stopper) is present and properly positioned to prevent contents from passing through stopper when stopper is closed (if applicable to product). Missing, worn or misaligned gaskets may cause product to leak. In general, contents should not be left in container for longer than 24 hours. However, the rate at which contents spoil depends on several factors.