Operation Manual

ManualsBrandsThetford ManualsCooktopsBasic Line 330

PCC

1274

–

Issue

USER AND INSTALLATION INSTRUCTIONS

FOR USE IN :- GB, IE, FR, NL, BE, LU, ES, IT, NO, DE, DK, SE

WARNING

• Read the instructions before use.

• Only use this appliance in a well ventilated area.

• This appliance must be installed in accordance with the regulations in force.

SPINFLO LIMITED,

19 Oakham Drive

, Parkwood Industri

Estate

Rutland Road, Sheffield S3 9QY, ENGLAND.

TEL: + 44 (0) 114 273 8157 FAX: + 44 (0) 114 275 3094

Summary of content (14 pages)

PAGE 1
USER AND INSTALLATION INSTRUCTIONS USER AND INSTALLATION INSTRUCTIONS PCC 1274– Issue 3 FOR USE IN :- GB, IE, FR, NL, BE, LU, ES, IT, NO, DE, DK, SE WARNING • Read the instructions before use. • Only use this appliance in a well ventilated area. • This appliance must be installed in accordance with the regulations in force. SPINFLO LIMITED, 19 Oakham Drive, Parkwood Industrial Estate Rutland Road, Sheffield S3 9QY, ENGLAND.
PAGE 2
ITEM 1 3 5 7 9 11 13 15 17 19 21 23 PART No S~G930.BK S~PCC0833 S~PCC2003 S~PCC0812 S~PCX0390 S~PCX0415 S~PCC0609 S~PCC0799 S~PCC0737 S~PCC1130 S~PCC1403 S~WIR0505 DESCRIPTION GLASS LID RAPID BURNER CAP HINGE BURNER SPREADER BUMP STOP FIXING BUSH CONTROL KNOB RAPID BURNER CUP CONTROL TAP (0.
PAGE 3
ITEM 1 3 5 7 9 11 13 15 17 19 21 PART No S~G0940 S~PCC0813 S~PCX0390 S~PCC2003 S~PCC1500 S~PCC0609 S~PCC0797 S~PCC1453 S~PCC1403 S~WIR0504 S~PCC1132 DESCRIPTION GLASS LID BURNER CAP BUMP STOP HINGE STICK ON FASCIA CONTROL KNOB BURNER CUP SPARK PROBE 300MM SPARK GENERATOR +VE WIRE TO GENERATOR THERMOCOUPLE 450MM ITEM 2 4 6 8 10 12 14 16 18 20 22 3 PART No S~PCC0693 S~PCC0814 S~PCX0415 S~PCC647 S~PCX0416 S~PCC0742 S~PCC1190 S~PCC0737 S~WIR0505 S~WIR0501 S~PCC1455 DESCRIPTION PAN SUPPORT BURNER SPREADER
PAGE 4
CONTROL POSITIONS – ALL MODELS FIG.
PAGE 5
APPLIANCE LOCATION Series 330, 340 & 345 the minimum allowable distance to combustible materials is as shown below FIG.
PAGE 6
Fig.
PAGE 7
Fig.
PAGE 8
SURFACE MOUNT FIXING – SERIES 330, 340 & 345 FIG. 6 1 3 5 7 9 Surface mounting bezel Bump stop Worktop Clamping screw Flush mounting bezel 2 4 6 8 Glass Lid Clamping bush Clamping arm Pressing FIG. 7 FLUSH MOUNT FIXING – SERIES 330, 340 & 345 An additional 6mm deep rebate MUST be cut into the worktop to accept the ‘Flush Mounting Bezel’.
PAGE 9
CONTENTS User’s Section Specification Introduction Using the Appliance ……………………………………………………Page 8 ……………………………………………………Page 9 ……………………………………………………Page 10 Installation and Servicing Installation Dimensions ……………………………………………………Pages 4-7 Specification ……………………………………………………Page 8 Installation Instructions ……………………………………………………Page 12 Maintenance & Servicing ……………………………………………………Page 13 Specification MODEL Dimensions (w x d X h)mm Heat Input Total heat input Burner rating Injector Size Bypass Size Spark Ignition
PAGE 10
INTRODUCTION In your own interest of safety, it is law that all gas appliances be installed by competent persons. CORGI (Confederation for the Registration of Gas Installers) registered installers undertake work to safe and satisfactory standards. Failure to install the appliance correctly could invalidate any warranty or liability claims and lead to prosecution. This appliance shall be installed in accordance with the local and national/European standards in force.
PAGE 11
OPERATION WARNING • When cooking, young children should be kept away. • Glass lids may shatter when heated. Turn off all burners before shutting the lid. • Spillage on the lid surface should be removed before opening the lid Burner Operation The burners on the appliance have fixed aeration and no adjustment is required. The burners should flame as follows:Propane Butane - The flames should burn quietly with a blue/green colour with no sign of yellow tips.
PAGE 12
OPERATION WARNING The Glass lid has the tendency to snap shut towards the end of lowering. This is caused by the travel lock action of the hinges as it is activated. Make sure all fingers are removed from appliance when closing the lid. DO'S AND DON'TS DO read the user instructions carefully before using the appliance for the first time. DO allow the burners to heat before using for the first time, in order to expel any smells before the introduction of food. DO clean the appliance regularly.
PAGE 13
INSTALLATION REGULATIONS AND STANDARDS In your own interest of safety, it is law that all gas appliances be installed by competent persons. CORGI (Confederation for the Registration of Gas Installers) registered installers undertake to work to safe and satisfactory standards. Failure to install the appliance correctly could invalidate any warranty or liability claims and lead to prosecution. This appliance shall be installed in accordance with the local and national/European standards in force.
PAGE 14
INSTALLATION INSTALLATION The appliance can be installed either onto the worktop or inset – ie flush fitting. A cut-out should be prepared in the worktop as shown in Figs. 4 & 5. If the appliance is to be flush mounted the worktop cut-out will require an additional rebate as detailed in Figs. 4 & 5. and shown in Fig. 7. Care should be taken to position the appliance central in the worktop cut-out to ensure an air gap is maintained between the appliance and the sides of the cut-out.