Owner's Manual
Interior Infrared
Camera
Installation Guide
Before
mstall1ng
the
interior
infrared
camera,
ensure
that
the
dash
cam
is
off.
1.
Install
at
any
suitable
location
near
the
dash
cam
.
2.
Ensure
the
following conditions
are
met
before
installation:
Ersure
that
tre
1;-iterior
infrared
c,imera
d()('s
not
obstruct
the
driver's
view
En~ure
that
tl•e
roor')
mirror
or'
he
da,h
cam
doe~
not
block
the
i
nterior
irfrdred
c,1rnu
Ersure
that
tl•e
in~tallatiori
locator
--an
be
easi
ly
accessed.
~Jote
the
irte•
ior
irfrare<
J
earner
as
d1:~1o
n
before
•nstallat
,
on.
[rsure
that
the
THINKWARE
:ocJo
on
the
carrera
mount
1s
fac
ntJ
thi>
w1ndst
:eld
.vhE n
installing
to
preve
nt t
he
video
frorr
being
recorded
ups,de
down.
3.
After
selecting
an
installation location,
clean
the
spot
using
a dry
rag
or
cloth.
If the installation
surface
is
wet,
or
if
foreign
materials
are
on
the
surface,
the
interior
infrared
camera
may
not
be
firmly
attached
to the
windshield
and
may
become
detached
while driving.
4.
Remove
the protective film
from
the mount's installation
surface
(1
).
Make
sure
the
THINKWARE
logo
on
the mount
is
facing
the
windshield.
Attach
the interior
infrared
camera
to the installation location
and
apply firm
pressure
to fix it to the
windshield
(2).
Then,
adjust
the
camera
angle
(3).
0 • •
5.
Connect
the
dash
cam
's
V-IN
port to the interior
infrared
camera's
V-OUT
port
via
the
cable
provided with the
camera
(1 ).
Then,
route
the
cable
neatly
so
that
it
does
not obstruct
the
driver's view
(2).
6.
After installing the interior
infrared
camera,
record
a video to
check
if
the interior
infrared
camera
is
properly
installed.
After the interior
infrared
camera
is
connected
to the
dash
cam,
it will turn
on
when
the
dash
cam
is
powered
on
.
The
interior
infrared
camera
is
designed
to
work
only
when
the
connected
dash
cam
1s
on.
If
the
interior
infrared
camera
is
not
working
properly,
turn
off
the
dash
cam
and
check
its
cable
connection
with
the
interior
infrared
camera.
TH
IN
KWARE
is
not
responsible
for
damages
to
the
interior
infrared
camera,
or
to
the
dash
cam
it
is
connected
to,
caused
by
incorrect
installation.
To
avoid
damage
due
to
incorrect
installation,
have
your
interior
infrared
camera
installed
by
a
professional
at
a
licensed
installation
l
ocation.
This
device
complies
with
part
15
of the
FCC
Rules.
Operation
is
subject
to
the
following
two
conditions:
, )
1111~
dev•ce
n c
Ir
__
.,e
har
JI
ference,
o
~d
(2)
This
device
rrJst cll(ept
any
nterference
rece:ved,
ncli.
d1nq
interfere
ncP
that
")JY
cau~e
undesired
operat1or
FCC
Compliance
Statement
Note.
This
equipment
has
been
tested
and
found
to
comply
with the limits for a
Class
B digital
device,
pursuant
to part
15
of the
FCC
Rules
.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
in
a
residential
installation
This
equipment
generates
,
uses
and
can
radiate
radio
frequency
energy
and,
if not
installed
and
used
in
accordance
with the instructions,
may
cause
harmful
interference
to
radio
communications,
However
,
there
is
no
guarantee
that interfer-
ence
will not
occur
in a
particular
installation.
If
this equipment
does
cause
harmful
interference
to
radio
or
television
reception
,
wh
i
ch
can
be
determined
by
turning
the equipment off
and
on,
the
user
is
encouraged
to
try to
correct
the i
nterference
by
one
or
more
of the following
measures:
Reorient
or
relocate
the
r
eceiv
ng
artenna
.
1
ncrease
the
se
p
arat1or
between
the
equipment
and
r
eceiver.
-
Conrect
the
eq
ui
pr1ent
irto
an
outlet
on
a
circL.
t
differen•
from
that
to
which
t
he
receiver
1s
connected.
-~or
sui
t
the
dealer
or
an
experienced
radio/TV
tecl'n
cian
for
help.
Caution
:
Any
changes
or modifications
to
the equipment not
expressly
approved
by
the party
responsible
for
compliance
could
void
your
authority to
operate
the
equipment.
Note:
This
unit
was
tested
with
shielded
cables
on
the
peripheral
devices.
Shielded
cables
must
be
used
with
the
unit to
insure
compliance
.
(
E:RoHS
Th
is
Cl
ass
B
dig
i
ta
l a
ppar
at
us
co
mpl
ies
with
Ca
nadian
IC
ES
-003
Item
Model
name
Camera
Reso
lu
tion
Frame
Rate
Viewing
Angle
Input
power
source
LED
Standard
BCH-{il0IR
1Megapixel.
1/
2.9
"
CMOS
HD(
1280
X
720)
30fps
Approximately
135
°
(diagonally
)
3.3V
DC
IR
LED
2ea
IR
LED
viewing
Angle
(
Typ.
)
IR
Wavelength(Typ.)
45
•
850nm
Current
Consumption
1.
17W
Operation
/
Storage
Temperature
-1
0"C
to
f:IJ
'
C/
-20
"C to
70
°C
Manufactured
byTHINKWARE
Made
in
Korea