Cut Sheet

G-9
Hardware and Rough-In Products
Anchors — Non-Metallic
Red-Cap
®
Screw Anchors
FOR TAPPING SCREWS DRILL* STD.
CAT. NO. SIZE SIZE LENGTH (IN.) HOLE (IN.) CTN.
50-210 #8 x
7
⁄8" 6, 7 or 8 1–1
1
⁄4
3
⁄16 1,000
50-230 #12 x 1" 9, 10 or 12 1–1
1
⁄4
1
⁄4 1,000
50-250 #16 x 1
3
⁄8" 14 or 16,
1
⁄4" Lag Screw 1
1
⁄4–1
1
⁄2
5
⁄16 500
Bulk
50-219 #8 x
7
⁄8" 6, 7 or 8 1–1
1
⁄4
3
⁄16 10,000
50-239 #12 x 1" 9, 10 or 12 1–1
1
⁄4
1
⁄4 10,000
50-259 #16 x 1
3
⁄8" 14 or 16,
1
⁄4" Lag Screw 1
1
⁄4–1
1
⁄2
5
⁄16 10,000
* When impact hammer drill is used, downsize drill hole
1
⁄ 32 ".
NOTE: For maximum holding power, select screw length
1
⁄ 4 " longer than anchor.
• Superior holding power in solid masonry
or concrete block
STD.
CAT. NO. DESCRIPTION CTN.
51-850 (100)
3
⁄16" x 1" Anchors w/ Nails 12
(1)
3
⁄16" Carbide-Tip Drill Bit
51-852 (100)
1
⁄4" x 1" Anchors w/ Nails 12
(1)
1
⁄4" Carbide-Tip Drill Bit
Anchors, nails and drill bit in reusable plastic kit box.
Hi-Drive
™
Nail Anchors
Hi-Drive
™
Nail Anchor Kit
DRILL* STD.
CAT. NO. SIZE (IN.) HOLE (IN.) CTN.
50-811
3
⁄16 x 1
3
⁄16 1,000
50-831
1
⁄4 x 1
1
⁄4 1,000
* When impact hammer drill is used, downsize drill hole
1
⁄ 32 ".
• For use in concrete, masonry, blocks, stone or plaster
• Dependable, low-cost, lightweight anchoring
Red-Cap
®
Anchor Kits
STD.
CAT. NO. DESCRIPTION CTN.
51-208 (100) #8 Anchors 12
(100) 6 x 1" Panhead Screws
(1)
3
⁄16" Carbide-Tip Drill Bit
51-212* (100) #12 Anchors 12
(100) 10 x 1" Combination Slot/Phillips Head Screws
(1)
1
⁄4" Carbide-Tip Drill Bit
51-212HX (100) #12 Anchors 12
(100) 10 x 1" Hex-Slotted Screws
(10)
1
⁄4" Carbide-Tip Drill Bit
51-216 (50) #16 Anchors 12
(50) 14 x 1
1
⁄64" Panhead Screws
(1)
5
⁄16" Carbide-Tip Drill Bit
* Now with combination Slot/Phillips screws.
• Red Cap
®
anchors, screws and drill
bit in reusable plastic kit box
Economy Screw
Anchor Kits
STD.
CAT. NO. DESCRIPTION CTN.
51-404* (100) #12 x 1" Screw Anchor 12
(100) 10 x 1" Slot/Phillips Head Screws
(1)
1
⁄4" Carbide-Tip Drill Bit
51-404HX (100) #12 x 1" Screw Anchor 12
(100) 10 x 1" Hex-Slotted Screws
(1)
1
⁄4" Carbide-Tip Drill Bit
* Now with Slot/Phillips screws.
Economy Plastic Screw Anchor
FOR TAPPING SCREWS DRILL* STD.
CAT. NO. SIZE SIZE LENGTH (IN.) HOLE (IN.) CTN.
50-404 #12 x 1" 10 to 12 1
1
⁄4 1,000
* When impact hammer drill is used, downsize drill hole
1
⁄ 32 ".
• Superior holding power in solid masonry
or concrete block