Cut Sheet

TA00970 E
2 -11 1/2
CAT. NO.**
FIG.
TRAD E
SI Z E
A ±.015 (.040)
INCH (mm)
B* ±.035 (0.90)
INCH (mm)
C ±.015 (0.40)
ACROSS
CORNERS
INCH (mm)
MIN.
THROAT
DIA. D
INCH (mm)
E
TH REA D
NPT ( I SO )
F* INCH (mm)
APPROX.
LT38P (-ISO20)(-PG11)(-PG13.5) 1
3/8
.570
(14.48)
1.595 (40.51)
1.354
(34.39)
.417
(10.59)
1/2
- 14
(20)

LT438P (-ISO20)(-PG11)(-PG13.5) 2 2.012 (51.10) 1.534 (38.96)
LT938P (-ISO20)(-PG11)(-PG13.5) 3 1.380 (35.05) 1.880 (47.75)
LT50P (-ISO20)(-PG13.5)(-PG16) 1
1/2
.570
(14.48)
1.636 (41.55)
1.448
(36.78)
.550
(13.97)
1/2
- 14
(20)

LT450P (-ISO20)(-PG13.5)(-PG16) 2 2.092 (53.14) 1.590 (40.39)
LT950P (-ISO20)(-PG13.5)(-PG16) 3 1.489 (37.82) 1.986 (50.44)
LT75P (-ISO25)(-PG21) 1
3/4
.582
(14.78)
1.757 (44.63)
1.740
(44.20)
.740
(18.80)
3/4
- 14
(25)

LT475P (-ISO25)(-PG21) 2 2.452 (62.28) 1.821 (46.25)
LT975P (-ISO25)(-PG21) 3 1.790 (45.47) 2.212 (56.18)
LT100P (-PG29) 1
1
.726
(18.44)
1.923 (48.84)
2.068
(52.53)
.940
(23.88)
1 - 11
1/2

LT4100P (-PG29) 2 2.684 (68.17) 2.034 (51.66)
LT9100P (-PG29) 3 2.104 (53.44) 2.508 (63.70)
LT125P (-PG36) 1
1-
1/4
.750
(19.05)
2.164 (54.97)
2.494
(63.35)
1.257
(31.93)
1
1
/
4
- 11
1/2

LT4125P (-PG36) 2 3.264 (82.91) 2.385 (60.58)
LT9125P (-PG36) 3 2.564 (65.13) 2.856 (72.54)
LT150P (-PG42) 1
1-
1/2
.767
(19.48)
2.353 (59.77)
2.784
(70.71)
1.453
(36.91)
1
1/2
- 11
1/2

LT4150P 2 3.605 (91.57) 2.604 (66.14)
LT9150P 3 2.854 (72.49) 3.144 (79.86)
LT200P (-PG48) 1
2
.794
(20.17)
2.605 (66.17)
3.362
(85.39)
1.883
(47.83)

LT4200P 2 4.210 (106.93) 3.050 (77.47)
LT9200P 3 3.432 (87.17) 3.675 (93.34)
*AFTER ASSEMBLY
FNM C- B
ONLY
C
F*
B*
D
E
TH READ
E
TH READ
C
B*
A
D
FIGURE 1
FNMC-B
ONLY
B*
F*
C
D
E
TH READ
FIGURE 2 FIGURE 3
A
A
** FITTINGS WITH ISO THREADS WILL HAVE THE ISO THREADED SUFFIX AS PART OF
THE CATALOG NUMBER. (EXAMPLE: LT38P-ISO20)
** FITTINGS WITH PG THREADS WILL HAVE THE PG THREADED SUFFIX AS PART OF THE
CATALOG NUMBER. (EXAMPLE: LT38P-PG11)
_
_
_
_
_
_
_
SUGGESTED
SPECIFICATION:
Where liquidtight
exible non-metallic
conduit (U.L.Type B) or
liquidtight exible
non-metallic tubing is
terminated to a box or
enclosure, the
non-metallic
connectors used shall
be able to
be installed without
disassembly and
provide a positive
installation criteria.
In the installed
condition, the
connector must
provide a seal meeting
watertight requirements
of NEMA Type 4 and
Type 6 enclosures.
The performance of
connectors shall be
unaffected by exposure
to detergents,
sanitizers, cutting
uids, wire pulling
compounds and oil
base industrial paints.
The connector must
also be capable of
withstanding Marine
environment and cold
impact simulating a
hammer blow. Installed
connectors shall be of
the elongated gland
type as manufactured
by Thomas & Betts
LT38P series.
WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine the suitability of this product for
the user's intended application. Thomas & Betts warrants that this product will be free from defects in materials or workmanship for a period of two (2) years
following the date of purchase. Upon prompt notication of any warranted defect, Thomas & Betts will, at its option, repair or replace the defective product.
Misuse, misapplication or modication of Thomas & Betts Products immediately voids all warranties.
Limitations and Exclusions: THE ABOVE WARRANTY IS THE SOLE WARRANTY CONCERNING THIS PRODUCT, AND IS IN LIEU OF ALL OTHER
WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, WHICH ARE SPECIFICALLY DISCLAIMED. LIABILITY FOR BREACH OF THE ABOVE WARRANTY IS LIMITED TO COST OF
REPAIR OR REPLACEMENT OF THE PRODUCT, AND UNDER NO CIRCUMSTANCES WILL THOMAS & BETTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
© 2014 Thomas & Betts. All Rights Reserved.