Note: roduction. of P l is Out Use Only.
Table Of Contents Subject: Page Number General Rules for Use and Handling of Muzzleloading Firearms ..............2 Nomenclature..............................................................................................8 Assembly & Disassembly of Your Fire Hawk..............................................9 Basic Equipment Needs For The Muzzleloading Shooter ..........................11 Understanding Black Powder and Pyrodex™ ..............................................12 Ignition....................
This booklet contains information that is essential to the safe use and maintenance of Thompson/Center’s modern-style in-line muzzleloaders. You must read this material in its entirety and fully understand its significance before you can safely use your muzzleloader. If a Thompson/Center muzzleloading firearm is loaned or sold (by an individual or a dealer), this booklet must accompany the firearm. Replacement booklets are available at no charge from our factory.
General Rules for Use and Handling of Thompson/Center Black Powder Muzzleloading Firearms 1 If you are unfamiliar with muzzleloading firearms seek professional instruction. Qualified organizations such as local gun clubs, The National Rifle Association, The National Muzzleloading Rifle Association and state Hunter Safety Programs offer approved courses which teach safe gun handling and proper hunting procedure.
cially manufactured Black Powder or Pyrodex propellant of the specific granulation or type called for in this booklet. By Black Powder we mean a powder which is manufactured specifically for use in muzzleloading firearms as opposed to smokeless powder which is manufactured for use in metallic cartridges or shotshells. NO smokeless powder, even those which appear black in color, should ever be used in a muzzleloading firearm. Be sure you know what type and granulation of powder you are loading.
until you are a safe distance away from the vehicle, road and companions. Never prime the firearm until you are actually ready to fire. 9 The T/C Fire Hawk™ is a modern "striker action" cap lock rifle, and does not have the half-cock notch that traditional cap locks have. There are two striker handle positions for the Fire Hawk; they are; “Cocked” and “Fired”. In the “Cocked” position, the striker is held rearward by the trigger sear which is in turn blocked by the manual thumb safety.
may cause serious injury and/or death to the shooter or bystanders and damage to property. 11 Never lean a charged and primed rifle against a tree, wall or any surface. Once the rifle has been charged it is your responsibility to guard it against accidental bumps. 12 Never store a charged muzzleloading firearm in a home, camp, vehicle or building. WARNING: After use, a muzzleloading firearm should be discharged (fired) into a suitable backstop before returning to the home or camp.
17 Do not smoke while using your muzzleloader. The spark from a lighted cigarette, cigar or pipe can ignite Black Powder, Pyrodex, Percussion Caps or Primers. WARNING: Smoking around a charged and/or primed muzzleloader, percussion caps, priming powder or supply of powder may cause premature firing of the gun or an explosion of the powder can, horn or flask causing serious injury and/or death to the shooter or bystanders and damage to property.
top quality brand only and follow the manufacturer’s instructions to the letter. WARNING: Never climb to or descend from a tree stand with a primed muzzleloading firearm. Never raise or lower a primed muzzleloading firearm to or from a tree stand. Failure to follow this rule may cause serious injury and/or death to the shooter or bystanders and damage to property. 23 Respect the muzzleloading firearm. Used properly your muzzleloader will give you years of pleasure.
the dealer selling the device or the person or persons installing it. 26 Use Thompson/Center scope mounts only. The Thompson/Center Catalog lists a series of scopes and mounts which are designed specifically for use with our firearms. These mounts make use of existing screw holes. Those who desire a scope sight should make use of Thompson/Center mounts. WARNING: Do not drill additional holes in the barrel as this could weaken the barrel structure leading to a rupture.
Ramrod Front Sight Stock Striker Butt Pad Receiver End Cap Green Dot marks "Safety" Position Safety Trigger Guard Trigger Nipple Red Dot marks "Fire" Position Barrel Rear Sight Receiver Striker Striker Handle Handle Striker Retainer Spring T/C Fire Hawk Nomenclature Thimble Know your Fire Hawk muzzleloading firearm before attempting to use it. This booklet will help you to become familiar with the various terms associated specifically with this type of firearm.
Assembly & Disassembly Of The Fire Hawk™ This Fire Hawk has four (4) basic parts groups: 1. The Barrel and Receiver Assembly - This assembly is held in the stock by two stock screws; one is located about 1" in front of the trigger guard and the other is the rear trigger guard screw. 2. The Stock Assembly - With sling swivel studs, trigger guard butt pad. 3. The Striker Assembly - The striker assembly is housed in the receiver, under spring tension.
11 Green Dot marks "Safety" Position Unscrew receiver end cap, remove striker spring, remove striker handle retainer, slide striker handle out and remove striker from receiver. Remove these two screws Red Dot marks "Fire" Position Remove ramrod The front trigger guard screw does not have to be removed in order to take the receiver and barrel out of the stock. Lift the receiver and barrel out of the stock Ensure that the firearm you are working with is unprimed and uncharged.
Basic Equipment For Shooting Your Thompson/Center Fire Hawk In order to shoot your Fire Hawk™ muzzleloading rifle, a minimum of accessories or equipment will be necessary, these items include: Do Not attempt to shoot your muzzleloading firearm until you have read this manual in its entirety and understood it fully. FAILURE TO READ AND FOLLOW THESE INSTRUCTIONS COULD RESULT IN AN ACCIDENTAL DISCHARGE, CAUSING INJURY AND/OR DEATH TO THE SHOOTER OR BYSTANDERS AND DAMAGE TO PROPERTY.
Understanding Black Powder And Pyrodex™ Make no mistake about it, Black Powder or Pyrodex are the only propellant powders that are safe to use in a muzzleloading firearm. Oh, you will hear, or possibly read, advice to the contrary but don’t follow it for you will never hear such advice from a competent source. The reason for using a low yield powder such as Black Powder or Pyrodex is quite basic and it is related to firearm design.
firearms. They should never be used in a muzzleloading firearm of any type. Some of these powders are “Black” in color making proper identification extremely important. It is the characteristic of Smokeless Powders to burn in a controlled manner within a given pressure range. Control of this pressure range requires the proper application of the powder to the specific purpose and in the quantities for which it was designed to be used.
Black Powder Chart Showing The Appropriate Use Of The Various Granulations FG (commonly called Single “F”) The muzzleloading enthusiast finds little use for this very coarse black powder. It’s use is restricted to the large bore (10, 8, 4 gauge) shotguns of yesterday. FFG (commonly called Double “F”) This is a very popular powder for the larger (.45 to .58 cal) rifles. It is also used for 12, 16, and 20 gauge muzzleloading shotguns.
When purchasing Black Powder be certain that it is in the original manufacturer’s container and that its granulation or type is clearly marked on the label. Follow the storage and handling precautions which are on the label. If you have any questions concerning the safe handling or storage of Black Powder, write to the manufacturer of the powder. Additional information on powder storage is available from the National Fire Protection Association, P.O. Box 9146, Quincy, Mass. 02269. Or call 1-800-344-3555.
Chart Showing Various Grades of PYRODEX™ and Their Intended Use ... PYRODEX® CTG FOR BLACK POWDER CARTRIDGES. This powder was designed to be used in early model breech loading cartridge firearms (rifles, pistols & shotguns) which were intended for use with Black Powder only. It has no application in Thompson/Center muzzleloading firearms. It is listed here simply for identification purposes. PYRODEX® RS (or PYRODEX SELECT “RS”) RIFLE & SHOTGUN POWDER.
Ignition in a Muzzleloader Considering that Black Powder ignites easily and burns almost instantaneously, it would not seem that ignition could create problems for the muzzleloading enthusiast. Yet, it was in the age of Black Powder that such terms as misfire, hangfire and flash in the pan found their origins. The problem, of course, is that the muzzleloader requires a great deal more care in its cleaning and handling than does a modern cartridge firearm (see section on “Cleaning Your Muzzleloading Firearm.
Black Powder Pressures And Velocities It is not the purpose of this manual to delve deeply into the complex subject of chamber pressure or how it relates to all firearms. There are, however, some basic differences between a muzzleloader and a modern cartridge firearm. The reader must understand and respect these differences if he or she is to use their T/C muzzleloader in a safe manner. Shooting muzzleloading firearms requires rethinking all that you have learned about firearms.
confines the powder charge to a given volume and controls headspace. Modern cartridge firearms are designed to withstand high working pressures since these same pressures make possible the high velocities, flat trajectories and increased range of modern ammunition. Yet, the modern firearm is no stronger than the cartridge case that is used in its chamber.
recorded the highest velocity in relation to the lowest pressure. Heavier loading showed marked increases in pressure and substantially more recoil for only minor gains in velocity. Fouling in the bore of a muzzleloader will increase pressure. When shooting a muzzleloader, consecutive shots without cleaning will display rapid shot-to-shot increases in pressure, a variation in velocity and a resultant decrease in accuracy.
The preceding text is offered in an attempt to guide the novice and to help him obtain optimum results from his muzzleloading firearm. The reader must bear in mind that a muzzleloader is not capable of developing the high velocity or handling the high pressures of a modern firearm. Restricted to a primitive design, the muzzleloading hunter takes game by depending upon a large caliber, heavy bullet traveling at a mild velocity.
Thompson/Center Muzzleloader Bullet Molds When using T/C molds, follow the instructions supplied with the mold block. Lead is a potent, systemic poison that serves no known useful function once absorbed by your body. Lead can be absorbed into your body by inhalation (breathing) and ingestion (eating). Taken in large enough doses, lead can kill you in a matter of days. Even in small quantities, lead dust, fumes or mist can be inhaled or ingested and cause serious injury in the respiratory system.
loys commonly found in Linotype and wheel weights contain antimony. While such alloys are very desirable for fixed cartridge projectiles, they are impractical for muzzleloading use. Alloys containing antimony are harder and lighter than pure lead. Consequently projectiles cast from such materials will be overly hard (depending on the amount of antimony present) and somewhat lighter than the bullet weight listed for the mold.
Accuracy with a muzzleloader is based on a paradox: an undersize ball is spun by rifling that it never touches! It is the job of the patch to hold the ball tightly against the powder charge until firing and to securely grip both the ball and the rifling so as to transfer the spin of the rifling to the projectile itself. If the patch fits too loosely, the ball will not spin and its flight will be unstable.
When targeting a muzzleloading firearm, it is wise to recover a few of the fired patches and to check their condition. Fired patches can usually be found lying on the ground about 10 yards in front of the muzzle. The following illustrations will help you to determine whether your patch and/or lubricant is doing its job. Lubricant is required to ease loading and prevent the patch material from burning.
Understanding The Fire Hawk™ Trigger, Striker and Safety Mechanism The Fire Hawk™ muzzleloading firearm is a modern cap lock rifle that combines both the functional aspects of an old-time cap lock with the looks of a modern bolt-action rifle. The Fire Hawk™ has several design features which are different than traditional muzzleloading firearms, and must be understood before you attempt to use and fire your Fire Hawk™. See the illustrations on page 28.
Photo #1 Striker is in the “Fired” position. The safety lever is fully forward and the striker is also fully forward and in contact with the nipple. Photo #1 Photo #2 Striker handle in the “Cocked” position with the thumb safety engaged (fully rearward). The thumb safety will now be lined up with the green dot on the stock. Photo #2 Photo #3 The Striker handle in the "Cocked" Position with the thumb safety in the “Fire” position. The thumb safety will now be in line with the red dot on the stock.
Trigger Adjustment For The Fire Hawk™ Any adjustments are to be made to Screws "A" and "B". A 5/64" hex wrench and a 1/4" open end wrench are required to perform adjustments. The trigger of the Fire Hawk™ is factory set for optimal weight of pull, sear engagement and over-travel. If further adjustment is required, the Fire Hawk™ is equipped with two trigger adjustment screws that can be adjusted by the shooter.
Trigger Adjustment for Sear Engagement (Screw "A" in diagram on page 29) Make sure that the firearm you are working with is uncharged and unprimed prior to making any trigger adjustments. FAILURE TO HEED THIS WARNING COULD RESULT IN ACCIDENTAL DISCHARGE WHICH MAY CAUSE INJURY AND/OR DEATH TO THE SHOOTER OR BYSTANDERS AND DAMAGE TO PROPERTY. Adjustment of the Fire Hawk trigger requires that the receiver/barrel be removed from the stock.
ry remove the receiver/barrel assembly from the stock. Step 6. After sear engagement adjustment is finalized, retighten the 1/4" lock nut, making sure that sear engagement adjustment screw (Screw “A”) remains in the same position. Step 7. Reassemble the rifle. To increase sear engagement from this minimum setting, the 5/64" hex screw (Screw "A") should be turned counterclockwise further than the one third minimum turn stated above.
Charging And Priming The Thompson/Center Fire Hawk™ If you have not read this manual in its entirety, do so before attempting to load your firearm. IMPROPER LOADING AND USE OF YOUR FIREARM CAN CAUSE INJURY AND/OR DEATH TO THE SHOOTER OR BYSTANDERS AND DAMAGE TO PROPERTY. The photo on page 33 shows a shooter in the process of loading a Fire Hawk™. Study this photo carefully and read all the captions before you proceed to charge your Fire Hawk™.
Loading & Use of a Fire Hawk™ Stay mentally alert. This task requires your complete attention. IMPROPERLY CHARGING YOUR T/C MUZZLE-LOADING RIFLE CAN BE DANGEROUS. STUDY THIS PHOTO CAREFULLY BEFORE PROCEEDING. Eyes, ears & arms protected. Do Not Smoke while loading any muzzleloader. Barrel held securely with muzzle upwards - directed away from your body. Keep components & reserve powder well away from the firearm.
IF YOU ARE LOADING A ROUND BALL WITH A CLOTH PATCH, PROCEED AS FOLLOWS. Lay your lubricated cloth patch over the muzzle and place the round ball in the center of the patch. Uniformity is important. Be certain that the patch is centered and that the weave of the cloth is placed exactly the same each time. Also, the sprue mark (flat section on a cast ball) should be in the up position and carefully centered.
way down the barrel until it contacts the powder charge. Seat the ball firmly against the powder charge but do not pound on it. Pounding on the ramrod will deform the ball. A deformed ball will not shoot accurately. Load and seat each ball with exactly the same pressure, shot after shot. With successive shots, fouling in the bore may build up in sufficient quantity to make loading more difficult, or even impossible.
If you are loading an all-lead conical like T/C’s MAXI-BALL® or MAXI-HUNTER® or a sabot like T/C’s Mag Express Sabot, proceed as follows; Do not use a cloth patch with these projectiles. Wipe the oil from the bore and follow the precharging instructions given for your particular style of rifle. Use Black Powder or Pyrodex only. Start with the lightest charges listed in our loading chart for your caliber. Use T/C graduated powder measure and measure each charge carefully.
ball, the lead bullet or sabot must be seated firmly against the powder charge. Seat the projectile with exactly the same pressure shot after shot. Study Photo “F”. Remove the ramrod before you prime the firearm. PHOTO F Use the ramrod to push the bullet down the barrel and to seat it against the powder charge. PROJECTILES MUST ALWAYS BE SEATED FIRMLY AGAINST THE POWDER CHARGE.
Do not prime the firearm until you are actually ready to fire and you have double checked to ensure that the striker handle is in the “cocked” position, the thumb safety is engaged (fully rearward) and ramrod has been removed from the bore. Thompson/Center does not recommend priming the firearm until the instant before actual firing. Carrying a charged, primed Fire Hawk can be dangerous.
When firing the Fire Hawk™, hold it tightly against the shoulder, allowing your body weight to absorb and buffer the force of the recoil. AN IMPROPERLY HELD FIREARM CAN “KICK” UPWARDS CAUSING FACIAL INJURY AND/OR BRUISING. If you decide not to fire, engage the thumb safety by pulling it fully rearward. Then remove the cap from the nipple.
Summary of Charging & Priming Your Thompson/Center Fire Hawk™ 1. Check to ensure that the firearm is uncharged. 2. Wipe the bore free of all oil. 3. Pointing the muzzle in a safe direction, snap several caps on the nipple, clearing away any oil residue which may be in the nipple channel. 4. Ensure that the striker handle is locked into the “Cocked” position and the thumb safety is engaged (fully rearward) and that it is aligned with the green dot on the stock. 5.
Pulling a Charge From Your Thompson/Center Fire Hawk™ Never attempt to pull a charge from your Fire Hawk™ until you are absolutely certain that the firearm is deprimed (percussion cap, removed from the nipple). Do not attempt to pull a charge from any gun until the powder charge has been rendered inert (barrel removed and its breech section submerged in water for at least one-half hour) as explained in the following text dealing with pulling a charge.
dle and slowly letting the striker go forward until it contacts the bare nipple. 2nd Step - Remove the ramrod from the thimble(s). 3rd Step - Remove the front stock assembly screw by turning it out counterclockwise (as viewed from the bottom of the gun). Then remove the screw from the back of the trigger guard (the front trigger guard screw holds the trigger guard to the stock, it does not hold the barrel/receiver assembly to the stock). 4th Step - The barrel and receiver may now be lifted out of the stock.
the muzzle end. Use care to ensure that the barrel is not marred in the process of clamping it. Be equally certain that it is clamped securely. Thread a T/C Ball & Bullet Puller of the proper caliber onto your ramrod and slip the ramrod into the bore until the screw on the puller contacts the projectile. Rotate the ramrod slowly clock wise as you tap lightly on the end of the ramrod with a hammer.
Cleaning Your Thompson/Center Fire Hawk™ Never attempt to clean a charged or primed muzzleloading firearm. AN ACCIDENTAL DISCHARGE CAN CAUSE INJURY AND/OR DEATH TO THE SHOOTER OR BYSTANDERS AND DAMAGE TO PROPERTY. Completely Disassemble your Fire Hawk by following the five-step procedure as detailed on page 9 and page 42. You are now ready to thoroughly clean your Fire Hawk™. The recommended cleaning method is as follows: 1.
3. Thoroughly wipe all the powder residue from the striker. You may want to submerge the striker in hot soapy water when scrubbing it. Dry the parts thoroughly. After cleaning your Fire Hawk rifle, it is recommended that you lightly lubricate the striker and trigger area of the rifle upon reassembly. Do Not use heavy grease or oil, as during cold weather, excessive lube may congeal and slow the striker fall (or keep it from striking the cap on the nipple altogether) when the trigger is pulled.
Make certain that the striker is in the “Cocked” position, the safety is engaged (fully rearward) and aligned with the green dot on the stock and the firearm is unprimed before attempting to clear any lubricant or debris from the receiver of your Fire Hawk. FAILURE TO FOLLOW THIS WARNING MAY RESULT IN INJURY AND/OR DEATH TO THE SHOOTER OR BYSTANDERS AND DAMAGE TO PROPERTY.
A PROJECTILE WHICH IS SEATED ONLY PART WAY DOWN THE BARREL SETS UP A HIGHLY DANGEROUS CONDITION WHICH MAY CAUSE A BURST BARREL AND INJURY AND/OR DEATH TO THE SHOOTER OR BYSTANDER AND DAMAGE TO PROPERTY. The projectile must be seated firmly against the powder charge. If the ball or bullet is not seated against the powder charge the firearm must be disassembled and the charge removed (see section on “Pulling a Charge”).
However, no matter what you use for a lube, consistency is the key to accuracy; so much that target shooters will use the tightest combination of patch and ball they can load, and they will wipe the bore between each shot. A good all natural bore cleaner like T/C’s No.13 Bore Cleaner will work extremely well in these situations, and because it contains no petroleum base, it is highly compatible for use with an all natural lube such as Natural Lube 1000 Plus Bore Butter.
sive fouling will be evident to the shooter as he experiences more difficulty in loading from shot to shot. The advantages to using all natural non-petroleum based lubes and cleaning products are many; the elimination of having to wipe your bore between shots or of having to immediately clean your gun after use; and the increase in accuracy due to more consistent velocities and more uniform pressures. However, the responsibility to clean your muzzleloader thoroughly before putting it away still exists.
Using Cleaning Implements With Your Thompson/Center Fire Hawk™ Thompson/Center muzzleloading rifles and pistols are supplied with a cleaning jag which is the proper size for the particular caliber. For cleaning use commercial cleaning patches (round or square) or pieces of discarded clothing. When using the cleaning jag,keep in mind that patch size and thickness are important. Start with a patch that is approximately 2 1/2" square (or in diameter).
Iron Sight Adjustment For The Fire Hawk™ The Fire Hawk™ is equipped with the a standard rifle rear sight as shown below which is adjustable for elevation by sliding the elevation blade up to raise the point of impact and down to lower the shot’s impact. It is necessary to loosen the elevation lock screw (by turning it counterclockwise, as viewed from the rear) before sliding the sight blade to the desired setting.
See the current T/C Catalog for scope mounting systems which can be used on your Fire Hawk. The receiver is factory drilled and tapped for these accessories. Service Department Service Department, Telephone #603-332-2333. Should your firearm require adjustment, repair or refinishing, we strongly recommend that the firearm be returned to the factory. There is no other way to ensure that the work will be done by a competent staff of trained technicians.
Thompson/Center does not approve or recommend any type of custom conversion or alteration other than those performed by the T/C Custom Shop. Muzzleloading firearms subjected to alteration are not covered by our factory warranty. Responsibility for alterations rests totally with the gunsmith or individual performing the work.
Bullet Data For The Various Thompson/Center Muzzleloading Rifles Round Balls For T/C Firearms .315" DIAMETER (47 grs.) Use with patch material No.7036, No.7042, No.7131, or No.7135 in .32 caliber models. .350" DIAMETER (65 grs.) Use with patch material No.7036, No.7042, No.7131, or No.7135 in .36 caliber models. .440" DIAMETER (127 grs.) Use with patch material No.7030, No.7043, No.7132, or No.7136 in .45 caliber models. .490" DIAMETER (175 grs.) Use with patch material No. 7030, No. 7043, No.7132, or No.
.50 Caliber (370 grs.) A medium and big game bullet for .50 caliber rifles. Factory lubricated with T/C Natural Lube 1000 Plus Bore Butter. .50 Caliber (460 grs.) A big game bullet for .50 caliber rifles. Now factory lubricated with T/C Natural Lube 1000 Plus Bore Butter. .54 Caliber (365 grs.) A medium (deer-sized) and big game .54 caliber bullet. Factory lubricated with T/C Natural Lube 1000 Plus Bore Butter. .54 Caliber (430 grs.) For medium (deer-sized) and large game, this .54 cal.
game. Factory lubricated with T/C Natural Lube 1000 Plus Bore Butter. .54 Caliber (435 grs.) Designed for maximum expansion on deer sized game. Factory lubricated with T/C Natural Lube 1000 Plus Bore Butter. .54 Caliber (540 grs.) Designed for medium (deer-sized) to large game. Now factory lubricated with T/C Natural Lube 1000 Plus Bore Butter. .58 Caliber (560 grs.) Maximum expansion in a heavy big game bullet. Now factory lubricated with T/C Natural Lube 1000 Plus Bore Butter.
Suggested Black Powder Loads For The Thompson/Center Fire Hawk™ The following charts show recommended charges for Thompson/Center In-Line muzzleloading rifles. Charges are listed by caliber and type of projectile. Note that in each instance a series of charges are listed. More than one charge is shown in each category to clearly illustrate the safe loading range for that particular caliber, model and projectile.
Suggested Black Powder Loads For The Thompson/Center Fire Hawk™ .50 Caliber Rifle For Use With .50 Caliber T/C Fire Hawk Patches Lubricated with Bore Butter Use Musket Cap, #11 Cap or 209 Primer .490" Diameter Lead Ball Weight (Grains) 175 Grain Using Round Ball Loads Black Powder Charge (Grains) Muzzle Velocity (Feet Per Second) Muzzle Energy (Foot Pounds) 50 grs. FFG 1357 F.P.S. 716 Ft. Lbs. 60 grs. FFG 1434 F.P.S. 799 Ft. Lbs. 70 grs. FFG 1643 F.P.S. 1050 Ft. Lbs. 80 grs. FFG 1838 F.P.S.
.50 Caliber Rifle For Use With .50 Caliber T/C Fire Hawk Bullets Lubricated with Bore Butter Use Musket Cap, #11 Cap or 209 Primer For Use With .50 Cal. Lead Bullets Using T/C .50 Caliber Maxi-Ball & Maxi-Hunter Loads Black Powder Charge (Grains) Muzzle Velocity (Feet Per Second) Muzzle Energy (Foot Pounds) 80 grs. FFG 1395 F.P.S. 1383 Ft. Lbs. 90 grs. FFG 1455 F.P.S. 1504 Ft. Lbs. Maxi Hunter 100 grs. FFG 1509 F.P.S. 1618 Ft. Lbs. and 110 grs. FFG 1570 F.P.S. 1751 Ft. Lbs. 120 grs.
.50 Caliber Rifle For Use With .50 Caliber T/C Fire Hawk Bullets Lubricated with Bore Butter Use Musket Cap, #11 Cap or 209 Primer Using T/C .50 Caliber Maxi-Ball & Maxi-Hunter Loads 50 Grain Pyrodex® Pellet Loading Data For Use With .50 Cal. Lead Bullets Powder Charge (50 Gr. Pellet) Muzzle Velocity (Feet Per Second) Muzzle Energy (Foot Pounds) 275 Gr. Maxi Hunter® 2 Pellets 1694 F.P.S. 2039 Ft. Lbs. & 320 Gr. Maxi-Ball® 3 Pellets 1995 F.P.S. 2828 Ft. Lbs. 350 Gr.
Assembly And Loading Of T/C Break-O-Way™ Sabots When loading T/C’s Break-O-Way Sabots, make sure that your gun is unprimed, and that your Break-O-Way Sabot has been properly assembled. Failure to assemble and load your sabot correctly could result in the bullet, sabot halves, or woven wool doughnut separating and disengaging from themselves. This could result in an air space between the components.
zleloading rifle. Study this photo carefully and read all the captions before you proceed to charge your rifle. The complete sabot unit should be seated firmly on the powder charge as indicated in the illustration below. Do not exceed the recommended loading data in this manual when using T/C Break-O-Way Sabots in Thompson/Center rifles. When using rifles not manufactured by Thompson/Center, do not exceed the recommended loads provided by the manufacturer of your rifle.
Suggested Black Powder Loads For Break-O-Way™ Sabots in the Fire Hawk™ Rifle .50 Caliber Rifle For Use Only With .50 Caliber T/C In-Line Muzzleloading Rifle Using .429" - .430" Bullets Use Musket Cap, No.11 Cap or 209 Primer For Use With .429" - .430" Bullets 200 Grain Using T/C .44 Caliber Break-O-Way™ Sabot Loads Black Powder Charge (Grains) Muzzle Velocity (Feet Per Second) Muzzle Energy (Foot Pounds) 80 grs. FFG 1634 F.P.S. 1186 Ft. Lbs. 90 grs. FFG 1673 F.P.S. 1243 Ft. Lbs. 100 grs.
Suggested Black Powder Loads For Break-O-Way™ Sabots in the Fire Hawk™ Rifle .54 Caliber Rifle For Use Only With .54 Caliber T/C In-Line Muzzleloading Rifle Using .429" - .430" Bullets Use Musket Cap, No.11 Cap or 209 Primer For Use With .429" - .430" Bullets 200 Grain Using T/C .44 Caliber Break-O-Way™ Sabot Loads Black Powder Charge (Grains) Muzzle Velocity (Feet Per Second) Muzzle Energy (Foot Pounds) 80 grs. FFG 1652 F.P.S. 1212 Ft. Lbs. 90 grs. FFG 1709 F.P.S. 1297 Ft. Lbs. 100 grs.
T/C Shipping Address: Thompson/Center Arms Company, Inc. Farmington Road Rochester, New Hampshire 03867 T/C Mailing Address: Thompson/Center Arms Company, Inc. P.O. Box 5002 Rochester, New Hampshire 03866 WARNING: Discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition may result in exposure to lead and other substances known to cause birth defects, reproductive harm and other serious physical injury. Have adequate ventilation at all times.
For Your Records Important Note: For fire, theft and insurance purposes, retain this record with your important papers in a safe place.
Thompson/Center Arms Co., Inc. P.O.
