HRH Range Hood Installation Guide and User Manual Applicable model: HRH3001U HRH3002U HRH3003U HRH3004U HRH3005U HRH3601U HRH3602U HRH3603U HRH3604U HRH3605U HRH4801U HRH4802U HRH4805U
Safety Notice Approved for residential type untis for residential use only read these insructions and be safe. Please read these instructions completely before starting. The installation of the appliance must respect all codes. Important: Save these instructions so that you can provide the electrical inspector in your area. Safety Warning: Turn off the circuit in the electrical panel and lock front panel to connect the cord of this unit.
space between the walls, ceilings, attics, crawl spaces or garages. Waring: TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT, Install this hood in accordance with all the requirements mentioned. WARNING: TO REDUCE THE RISK OF FIRE, GREASE THE RANGE. 1. Never leave the stove unattended when it is at a high temperature. Boil overs cause smoke and fat that overflows can ignite. Heat the oil slowly at a low or medium temperature. 2. Always operate the hood when you use the stove to high heat or when you Flame.
Electrical requirements and installation requirements Power Requirements IMPORTANT Observe all governing codes and ordinances. The customer is responsible for: Contacting an electrician-installer. Check that the electrical installation is adequate and in conformance with the National Electrical Code, ANSI / NFPA 70 (latest edition *) or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 (the latest edition **) of the CSA, and all codes and ordinances in your area.
Examples and positioning possibilities ducts Follow the letter of the guidelines presented in this manual. The manufacturer declines any liability with respect to any loss, damage or fire caused by non-observance of the instructions contained in this manual. Ventilation methods The hood is equipped with a vertical transition to remove fumes outside. Recommended diameter conduit model and wall chimney hood and hood island: vertical round pipe 7'' tolerance + or – 1.
Do not cut a joist or stud unless it is absolutely necessary to do so. If you need to cut a joist or stud, you must build a support Framework, hardware supplied can secure the hood to most walls and ceilings. However, you should ask a qualified technician to check the strength of materials depending on the type of wall or ceiling. Before cutting, make sure there is enough clearance in the ceiling or wall for the outlet pass. You can determine for yourself how high you install the hood above the stove.
Clearance Training Caution: When install the hood, the height should not be too high or too low. Before the installation, please inspect the maximum height of your ceiling and bonnet.Too high, will affect the efficiency of the hood; too low, stove temperature will damage some parts of the hood.
Installation If possible, unplug the stove and move it in order to have better access to the rear wall. Otherwise, place a thick blanket on the counter and the cooking surface to protect it from damage and dirt. Select a flat surface for assembling the device. Then put the debris of the cover and hardware on to the protective cap. Determine and mark the center line on the wall where you installed the canopy hood. Determine a comfortable height for the user and mark it on the wall behind the stove top.
Necessary Tools
HRH3003U
Installation dimension figure of HRH3004U as below:
HRH3004U Installation dimension figure of HRH3001U and HRH3002U as below: Fix 6pcs screws( see figure 4) to the installation dead plate Fix the installation dead plate to the wall by screws( see figure 5) Use double-faced aluminum foil sealed-joint( see figure 6) Power line color (black to black, white to white, green to green) (see figure 7) Oil box of the hood (see figure 8) Installation of clapboard filter screen (see figure 9)
Figure4 Figure5
HRH3001U HRH3002U
Description orders for model HRH3001U HRH3003U HRH3004U Automatic activation control function of the sensor: There are 5pcs sensor buttons,1pc remote control signal lamp(remote controller included), 2pcs stainless steel grease boxes, 2pcs stainless steel baffle filters and 2pcs led bulbs( 12V/1.5W). A0 button: Remote control signal lamp A1 button: Power( on/off) A2 button: LED bulb A3 button: Display screen A4 button: Time Delay.
button to increase delay-time, set the figure timers as the time you want, max delay-time is 15 minutes. If time-setting changes from A6 button to A5 button, during the process, speed changes,but does not affect count down. Off immediately Press A1 button two times, fan turn off immediately. Bulb control Press A2 button once, turn on the lights, and again to turn off. Press A2 button or A4 button, then will not able to turn on LED light.
MAINTENANCE WARNING Before servicing or cleaning unit, switch power off at service panel and lock in access to prevent it being switched on accidentally. If the power panel can not be locked, put a prominent warning device, such as a brightly coloured label. Grease filters The grease filters should be cleaned once a month or as needed. To remove grease filter, pull the metal latch down. This will disengage the filter hood. Tilt the filter down, then remove.
WARRANTY THE HOOD VENETO TWO YEAR LIMITED WARRANTY This product has been manufactured by Thorkitchen Corporation.1335 Fortune Bay Ct,Hoffman Estates IL 60192. Thorkitchen Corporation disclaims all express warranties except for the following: This warranty applies to products purchased and located in the United States. Products purchased or located outside this area are excluded.
appliances used for commercial applications.Should the appliance be sold by the original purchaser during the warranty period, the warranty shall extend to the new owner until the expiration date of the original purchaser’s warranty period. Warranty and Product Registration Thorkitchen Corporation is not responsible for incidental or consequential damages.Under no circumstances will Thorkitchen’s liability exceed the cost that you paid for the product.