Technical Specifications

SealBest 800 - Fast-Drying Supreme Driveway Sealer & Filler
SealBest 800
Fast-Drying Supreme Driveway Sealer & Filler
Revised: 01/11
Manufacturer:
ThorWorks Industries, Inc.
2520 S. Campbell St.
Sandusky, OH 44870
Phone: [phone]
Fax: [phone]
Description
SealBest 800 Driveway Sealer & Filler is a high
quality polymer modified, fast drying asphalt
emulsion based pavement sealer. SealBest 800 is
fortified with sand for added filling, durability, and
traction. SealBest 800’s No-Stir Gel Formula allows
for ease of application.
Uses
Beautifies and protects asphalt pavement surfaces
including driveways, walkways, and more.
Coverage
One 4.75-gallon pail of SealBest 800 will cover
approximately 250-350 square feet for one coat. A
second coat may be applied for added durability.
Coverage will ultimately be dependant upon
pavement porosity. Extremely porous pavement
may significantly reduce product coverage.
Directions
SURFACE PREPARATION: Sweep all dirt and loose
debris from driveway surface. Scrub all oil and
gasoline stains with household detergent and
water. Rinse off entire driveway surface with water.
Do not leave any standing water or puddles.
CLEAN AND FILL CRACKS: Remove dirt and
vegetation from cracks with screwdriver, wire
brush, or other suitable instrument. Flush out crack
with hose and water and allow to dry. Fill cracks up
to 1/2” wide with SealBest Pourable Crack Filler. Fill
larger cracks up to 1” wide with SealBest Trowel
Grade Crack Filler. Allow crack filler to dry 24 hours
prior to applying SealBest 800 Driveway Sealer &
Filler.
SEAL OIL SPOTS: Apply SealBest Oil Spot Primer
to properly cleaned oil and gasoline stains. Allow
oil spot primer to dry completely prior to applying
SealBest 800 Driveway Sealer & Filler.
APPLICATION: Before opening, turn pail upside
down and rock back and forth to loosen material
in pail. If desired, SealBest 800 may be stirred to
enhance pouring. Do not dilute. Pour a narrow
puddle of material across the driveway. Use
suitable driveway sealer applicator to spread
material. For best results, walk across driveway
from side to side with squeegee or brush applicator.
Continuously feed puddle with fresh material. For
optimum performance (and warranty purposes)
apply two coats at an application rate of no more
than 350 square feet per 4.75-gallon pail per coat.
Drying Time
Allow first coat to dry completely before applying
second coat. Allow sealer to cure 24-48 hours before
opening up to vehicle traffic.
Clean Up
Wash tools with water before material dries.
Important
Read entire label before using. Application
temperature must be a minimum of 60 °F and
rising. Do not apply when temperature is expected
to drop below 60 °F within a 24 hour period. Be
sure to wear eye protection, gloves, long pants, and
long sleeves when mixing and applying SealBest
materials. In areas where dew or fog accumulates
in the early evening, it is best to coat in the
morning. Stop coating by early afternoon (3:00 pm)
to prevent wash off, which will occur if dew, fog,
or rain arrive before coating dries. Do not apply
if rain is imminent or forecast within 24 hours of
application. DO NOT USE ON CONCRETE SURFACES.
Precautions
• DoNotHeatOrThin
• DoNotFreeze
• DoNotStoreAtTemperaturesBelow50ºF
Safety And Environmental Precautions
• ReferToMaterialSafetyDataSheetBeforeUsing
• ForExteriorApplicationOnly
• ApplyInAWellVentilatedArea
• CloseContainerWhenNotInUse
• EnvironmentalInformationIsOnTheMaterial
 SafetyDataSheet
• DoNotReuseEmptyContainer
• VolatileOrganicContent(VOC)Is50
 Gm/LiterMax
• KeepOutOfReachOfChildren
www.sealbest.com
h5065