User's Manual
Table Of Contents
- Safety summary
- Preface
- Training information
- About this manual
- Introduction
- Installation
- Interface description
- Configuration
- Service & maintenance
- Technical specifications
- NMEA sentences
- B.1 NMEA sentences used
- B.2 Sentence use reference
- B.2.1 ABK - AIS addressed and binary broadcast acknowledgement (output)
- B.2.2 ABM - AIS addressed binary and safety related message (input)
- B.2.3 ACA - AIS channel assignment message (input / output)
- B.2.4 ACK - Acknowledge alarm (input)
- B.2.5 AIR - AIS interrogation request (input)
- B.2.6 ALR - Set alarm state (output)
- B.2.7 BBM - AIS broadcast binary message (input)
- B.2.8 DTM - Datum reference (input)
- B.2.9 EPV - Command or report equipment property value (input / response output)
- B.2.10 GBS - GNSS satellite fault detection (input)
- B.2.11 GGA - Global positioning system (GPS) fix data (input)
- B.2.12 GNS - Fix data (input)
- B.2.13 HBT - Heartbeat supervision sentence (input)
- B.2.14 HDT - Heading true (input)
- B.2.15 LR1 - AIS long-range reply sentence 1 (output)
- B.2.16 LR2 - AIS long-range reply sentence 2 (output)
- B.2.17 LR3 - AIS long-range reply sentence 3 (output)
- B.2.18 LRF - AIS long-range function (input / output)
- B.2.19 LRI - AIS long-range interrogation (input / output)
- B.2.20 NAK - Negative acknowledgement (output)
- B.2.21 PTHRAOC - AIS operational control (input / output)
- B.2.22 PTHRROS - Radio operational status (output)
- B.2.23 RMC - Recommended minimum specific GNSS data (input)
- B.2.24 ROT - Rate of turn (input)
- B.2.25 SPW - Security password sentence (input)
- B.2.26 SSD - AIS ship static data (input / output)
- B.2.27 THS -True heading and status (input)
- B.2.28 TRL - AIS transmitter non functioning log (output)
- B.2.29 TXT - Text transmission (output)
- B.2.30 VBW - Dual ground/water speed (input)
- B.2.31 VDM - AIS VHF data-link message (output)
- B.2.32 VDO - AIS VHF data-link own-vessel report (output)
- B.2.33 VER - Version (output)
- B.2.34 VSD - AIS voyage static data (input / output)
- B.2.35 VTG - Course over ground and ground speed (input)
- B.2.36 ZDA - Time and Date (output)
- Supported keys
- Glossary
- Index
Physical installation of the SAILOR 6280 AIS System
3-8 Chapter 3: Installation 98-137573-A
Connector overview – SAILOR 6282 AIS Transponder
The following figure shows the connectors of the SAILOR 6282 AIS Transponder.
VHF/GPS
Connect the VHF antenna or the combined VHF/GPS antenna to this connector.
GPS
Connect the cable from the SAILOR 6285 GPS Antenna - Active to this connector.
Grounding
To connect the SAILOR 6282 AIS Transponder to ship ground, do as
follows:
1. Connect a ground cable of shortest possible length and minimum
4 mm
2
cross section to the Ground stud and fasten it with the wing
nut.
2. Connect the other end of the cable to ship ground.
DC Power input 12–24 VDC
For more information on DC power input, pin allocation and instructions how to connect
DC power see Connecting DC power on page 4-2.
Connector overview – spring loaded terminals
The following figure shows the spring loaded terminals of the SAILOR 6283 AIS Connection
Box and Wall Tray.
Figure 3-6: Connectors of the SAILOR 6282 AIS Transponder
VHF/GPS
GPS
12-24V DC
FUSE
SUB-D50
1
Ground stud