User's Manual
Table Of Contents
- Safety summary
- Preface
- Training information
- About this manual
- Introduction
- Installation
- Interface description
- Configuration
- Service & maintenance
- Technical specifications
- NMEA sentences
- B.1 NMEA sentences used
- B.2 Sentence use reference
- B.2.1 ABK - AIS addressed and binary broadcast acknowledgement (output)
- B.2.2 ABM - AIS addressed binary and safety related message (input)
- B.2.3 ACA - AIS channel assignment message (input / output)
- B.2.4 ACK - Acknowledge alarm (input)
- B.2.5 AIR - AIS interrogation request (input)
- B.2.6 ALR - Set alarm state (output)
- B.2.7 BBM - AIS broadcast binary message (input)
- B.2.8 DTM - Datum reference (input)
- B.2.9 EPV - Command or report equipment property value (input / response output)
- B.2.10 GBS - GNSS satellite fault detection (input)
- B.2.11 GGA - Global positioning system (GPS) fix data (input)
- B.2.12 GNS - Fix data (input)
- B.2.13 HBT - Heartbeat supervision sentence (input)
- B.2.14 HDT - Heading true (input)
- B.2.15 LR1 - AIS long-range reply sentence 1 (output)
- B.2.16 LR2 - AIS long-range reply sentence 2 (output)
- B.2.17 LR3 - AIS long-range reply sentence 3 (output)
- B.2.18 LRF - AIS long-range function (input / output)
- B.2.19 LRI - AIS long-range interrogation (input / output)
- B.2.20 NAK - Negative acknowledgement (output)
- B.2.21 PTHRAOC - AIS operational control (input / output)
- B.2.22 PTHRROS - Radio operational status (output)
- B.2.23 RMC - Recommended minimum specific GNSS data (input)
- B.2.24 ROT - Rate of turn (input)
- B.2.25 SPW - Security password sentence (input)
- B.2.26 SSD - AIS ship static data (input / output)
- B.2.27 THS -True heading and status (input)
- B.2.28 TRL - AIS transmitter non functioning log (output)
- B.2.29 TXT - Text transmission (output)
- B.2.30 VBW - Dual ground/water speed (input)
- B.2.31 VDM - AIS VHF data-link message (output)
- B.2.32 VDO - AIS VHF data-link own-vessel report (output)
- B.2.33 VER - Version (output)
- B.2.34 VSD - AIS voyage static data (input / output)
- B.2.35 VTG - Course over ground and ground speed (input)
- B.2.36 ZDA - Time and Date (output)
- Supported keys
- Glossary
- Index
Presentation Interfaces
4-8 Chapter 4: Interface description 98-137573-A
4.3.4 Pilot plug connection
The pilot plug provides a connection to the SAILOR 6282 AIS Transponder for pilots using
the standard pilot plug connector. This connector is supplied with the SAILOR 6282 AIS
Transponder. Mount it in an appropriate position for easy access by the pilot. The
connector kit for the pilot plug consists of the following items:
Connect the pilot plug as shown below:
Type Manufacturer Part number
Pilot Plug Connector AMP/Tyco 206486-2, Square Flange
Contact Pins AMP/Tyco 66570-3, solder type
Sealing Cap AMP/Tyco 208800-1
Table 4-5: Connector kit for the pilot plug
Figure 4-5: Pilot plug connection
1
5
23
4
6
7
9
8
Rx A
PI 2
Rx B
Rx C
Tx A
Tx B
Tx C