User's Manual
Table Of Contents
- Safety summary
- Preface
- Training information
- About this manual
- Introduction
- Installation
- Interface description
- Configuration
- Service & maintenance
- Technical specifications
- NMEA sentences
- B.1 NMEA sentences used
- B.2 Sentence use reference
- B.2.1 ABK - AIS addressed and binary broadcast acknowledgement (output)
- B.2.2 ABM - AIS addressed binary and safety related message (input)
- B.2.3 ACA - AIS channel assignment message (input / output)
- B.2.4 ACK - Acknowledge alarm (input)
- B.2.5 AIR - AIS interrogation request (input)
- B.2.6 ALR - Set alarm state (output)
- B.2.7 BBM - AIS broadcast binary message (input)
- B.2.8 DTM - Datum reference (input)
- B.2.9 EPV - Command or report equipment property value (input / response output)
- B.2.10 GBS - GNSS satellite fault detection (input)
- B.2.11 GGA - Global positioning system (GPS) fix data (input)
- B.2.12 GNS - Fix data (input)
- B.2.13 HBT - Heartbeat supervision sentence (input)
- B.2.14 HDT - Heading true (input)
- B.2.15 LR1 - AIS long-range reply sentence 1 (output)
- B.2.16 LR2 - AIS long-range reply sentence 2 (output)
- B.2.17 LR3 - AIS long-range reply sentence 3 (output)
- B.2.18 LRF - AIS long-range function (input / output)
- B.2.19 LRI - AIS long-range interrogation (input / output)
- B.2.20 NAK - Negative acknowledgement (output)
- B.2.21 PTHRAOC - AIS operational control (input / output)
- B.2.22 PTHRROS - Radio operational status (output)
- B.2.23 RMC - Recommended minimum specific GNSS data (input)
- B.2.24 ROT - Rate of turn (input)
- B.2.25 SPW - Security password sentence (input)
- B.2.26 SSD - AIS ship static data (input / output)
- B.2.27 THS -True heading and status (input)
- B.2.28 TRL - AIS transmitter non functioning log (output)
- B.2.29 TXT - Text transmission (output)
- B.2.30 VBW - Dual ground/water speed (input)
- B.2.31 VDM - AIS VHF data-link message (output)
- B.2.32 VDO - AIS VHF data-link own-vessel report (output)
- B.2.33 VER - Version (output)
- B.2.34 VSD - AIS voyage static data (input / output)
- B.2.35 VTG - Course over ground and ground speed (input)
- B.2.36 ZDA - Time and Date (output)
- Supported keys
- Glossary
- Index
Service Interface
98-137573-A Chapter 5: Configuration 5-5
5555
Configuration
Using a PC with Thrane Management Application (TMA)
To access the built-in web interface, also called the Service Interface, via the TMA do as
follows:
1. Switch on the SAILOR 6004 Control Panel and make sure that DC power is provided for
the SAILOR 6282 AIS Transponder.
2. Connect a PC to the same network as the SAILOR 6282 AIS Transponder (preferably a
direct connection to the Ethernet connector of the SAILOR 6282 AIS Transponder).
3. Start the TMA (v. 1.04 or higher) and click on the SAILOR 6282 AIS Transponder (TT-
6282 AIS).
4. Click the icon Management and then Web interface. The web interface opens in a
browser window.
Using a PC and an Internet browser
To access the Service Interface, with a PC and an Internet browser do as follows:
1. Switch on the SAILOR 6004 Control Panel and make sure that DC power is provided for
the SAILOR 6282 AIS Transponder.
2. Tap the menu item in the top right corner, swipe upwards and tap Settings.
3. In the section Connection, two IP addresses are listed:
• Remote IP address – IP address of the SAILOR 6282 AIS Transponder
• Own IP Address – IP address of the SAILOR 6004 Control Panel
These IP addresses are assigned automatically. Note down the IP address of the SAILOR
6282 AIS Transponder.
4. Connect a PC to the same network as the SAILOR 6282 AIS Transponder - or - SAILOR
6004 Control Panel.
Figure 5-4: Accessing the web interface using the TMA