User's Manual
Table Of Contents
- Safety summary
- Preface
- Training information
- About this manual
- Introduction
- Installation
- Interface description
- Configuration
- Service & maintenance
- Technical specifications
- NMEA sentences
- B.1 NMEA sentences used
- B.2 Sentence use reference
- B.2.1 ABK - AIS addressed and binary broadcast acknowledgement (output)
- B.2.2 ABM - AIS addressed binary and safety related message (input)
- B.2.3 ACA - AIS channel assignment message (input / output)
- B.2.4 ACK - Acknowledge alarm (input)
- B.2.5 AIR - AIS interrogation request (input)
- B.2.6 ALR - Set alarm state (output)
- B.2.7 BBM - AIS broadcast binary message (input)
- B.2.8 DTM - Datum reference (input)
- B.2.9 EPV - Command or report equipment property value (input / response output)
- B.2.10 GBS - GNSS satellite fault detection (input)
- B.2.11 GGA - Global positioning system (GPS) fix data (input)
- B.2.12 GNS - Fix data (input)
- B.2.13 HBT - Heartbeat supervision sentence (input)
- B.2.14 HDT - Heading true (input)
- B.2.15 LR1 - AIS long-range reply sentence 1 (output)
- B.2.16 LR2 - AIS long-range reply sentence 2 (output)
- B.2.17 LR3 - AIS long-range reply sentence 3 (output)
- B.2.18 LRF - AIS long-range function (input / output)
- B.2.19 LRI - AIS long-range interrogation (input / output)
- B.2.20 NAK - Negative acknowledgement (output)
- B.2.21 PTHRAOC - AIS operational control (input / output)
- B.2.22 PTHRROS - Radio operational status (output)
- B.2.23 RMC - Recommended minimum specific GNSS data (input)
- B.2.24 ROT - Rate of turn (input)
- B.2.25 SPW - Security password sentence (input)
- B.2.26 SSD - AIS ship static data (input / output)
- B.2.27 THS -True heading and status (input)
- B.2.28 TRL - AIS transmitter non functioning log (output)
- B.2.29 TXT - Text transmission (output)
- B.2.30 VBW - Dual ground/water speed (input)
- B.2.31 VDM - AIS VHF data-link message (output)
- B.2.32 VDO - AIS VHF data-link own-vessel report (output)
- B.2.33 VER - Version (output)
- B.2.34 VSD - AIS voyage static data (input / output)
- B.2.35 VTG - Course over ground and ground speed (input)
- B.2.36 ZDA - Time and Date (output)
- Supported keys
- Glossary
- Index
Service Interface
5-14 Chapter 5: Configuration 98-137573-A
Note
The sensor inputs can in principle also be configured to decode the same sentence
categories as the PI ports, but as the sensor ports are pure input ports query
sentences will not be acknowledged correctly.
Figure 5-12: Service Interface: Interface settings – Sensor Settings
Item Description
Name You can name SENSOR1 through SENSOR3 according to your system
requirements.
Baud Use the drop-down list to change the baud rate, if needed (default: 4800 baud).
Talker ID Filter Enter NMEA talker ID. Replace * from left to right.
Example: AI ZZ BI0000 CC9999 GH ZI VA ST **
Talker ID filters are used to ensure that the SAILOR 6282 AIS TransponderAIS
does not get the same sentence type from more than one physical sensor.
If one of the inputs (PI, Sensor or LWE) provides sentences that shall be ignored
by the AIS, make a positive Talker ID filter list for this port listing all the talker ID's
that shall be used by the AIS on this interface. By leaving out the Talker IDs that
are not to be used by the AIS, these are filtered out.
Decoder Select which NMEA sentences you want to decode.
For further information see Table B-2 on page B-2.
Table 5-3: Interface settings, Sensor Settings