User's Manual
Table Of Contents
- Safety summary
- Preface
- Training information
- About this manual
- Introduction
- Installation
- Interface description
- Configuration
- Service & maintenance
- Technical specifications
- NMEA sentences
- B.1 NMEA sentences used
- B.2 Sentence use reference
- B.2.1 ABK - AIS addressed and binary broadcast acknowledgement (output)
- B.2.2 ABM - AIS addressed binary and safety related message (input)
- B.2.3 ACA - AIS channel assignment message (input / output)
- B.2.4 ACK - Acknowledge alarm (input)
- B.2.5 AIR - AIS interrogation request (input)
- B.2.6 ALR - Set alarm state (output)
- B.2.7 BBM - AIS broadcast binary message (input)
- B.2.8 DTM - Datum reference (input)
- B.2.9 EPV - Command or report equipment property value (input / response output)
- B.2.10 GBS - GNSS satellite fault detection (input)
- B.2.11 GGA - Global positioning system (GPS) fix data (input)
- B.2.12 GNS - Fix data (input)
- B.2.13 HBT - Heartbeat supervision sentence (input)
- B.2.14 HDT - Heading true (input)
- B.2.15 LR1 - AIS long-range reply sentence 1 (output)
- B.2.16 LR2 - AIS long-range reply sentence 2 (output)
- B.2.17 LR3 - AIS long-range reply sentence 3 (output)
- B.2.18 LRF - AIS long-range function (input / output)
- B.2.19 LRI - AIS long-range interrogation (input / output)
- B.2.20 NAK - Negative acknowledgement (output)
- B.2.21 PTHRAOC - AIS operational control (input / output)
- B.2.22 PTHRROS - Radio operational status (output)
- B.2.23 RMC - Recommended minimum specific GNSS data (input)
- B.2.24 ROT - Rate of turn (input)
- B.2.25 SPW - Security password sentence (input)
- B.2.26 SSD - AIS ship static data (input / output)
- B.2.27 THS -True heading and status (input)
- B.2.28 TRL - AIS transmitter non functioning log (output)
- B.2.29 TXT - Text transmission (output)
- B.2.30 VBW - Dual ground/water speed (input)
- B.2.31 VDM - AIS VHF data-link message (output)
- B.2.32 VDO - AIS VHF data-link own-vessel report (output)
- B.2.33 VER - Version (output)
- B.2.34 VSD - AIS voyage static data (input / output)
- B.2.35 VTG - Course over ground and ground speed (input)
- B.2.36 ZDA - Time and Date (output)
- Supported keys
- Glossary
- Index
Alarms and notifications
6-4 Chapter 6: Service & maintenance 98-137573-A
6.4 Alarms and notifications
6.4.1 Overview
If an alarm is reported from the SAILOR 6282 AIS Transponder a flashing red triangle appears in the
bottom bar of the SAILOR 6004 Control Panel display:
• Flashing, bright red triangle: Unacknowledged alarm(s).
• Faded red triangle: Acknowledged alarm(s).
To acknowledge an alarm do as follows:
1. Tap the flashing, bright red triangle to display the list with active alarms.
2. Tap the alarm to acknowledge the alarm.
When all active alarms are acknowledged the bright red triangle turns into a faded red triangle.
Internal hardware errors in the SAILOR 6282 AIS Transponder are reported as Rx channel
malfunction alarm messages. See Table 6-1 on page 5 for further details.
If the SAILOR 6004 Control Panel cannot retrieve the time for an alarm from the SAILOR 6282 AIS
Transponder, this is marked by adding (CPT) to the alarm title. See the example in the following
figure.
Figure 6-5: Active alarms (example)
Figure 6-6: Active alarms, no time stamp from SAILOR 6282 AIS
Transponder (example)
1
2