User's Manual
Table Of Contents
- Safety summary
- Preface
- Training information
- About this manual
- Introduction
- Installation
- Interface description
- Configuration
- Service & maintenance
- Technical specifications
- NMEA sentences
- B.1 NMEA sentences used
- B.2 Sentence use reference
- B.2.1 ABK - AIS addressed and binary broadcast acknowledgement (output)
- B.2.2 ABM - AIS addressed binary and safety related message (input)
- B.2.3 ACA - AIS channel assignment message (input / output)
- B.2.4 ACK - Acknowledge alarm (input)
- B.2.5 AIR - AIS interrogation request (input)
- B.2.6 ALR - Set alarm state (output)
- B.2.7 BBM - AIS broadcast binary message (input)
- B.2.8 DTM - Datum reference (input)
- B.2.9 EPV - Command or report equipment property value (input / response output)
- B.2.10 GBS - GNSS satellite fault detection (input)
- B.2.11 GGA - Global positioning system (GPS) fix data (input)
- B.2.12 GNS - Fix data (input)
- B.2.13 HBT - Heartbeat supervision sentence (input)
- B.2.14 HDT - Heading true (input)
- B.2.15 LR1 - AIS long-range reply sentence 1 (output)
- B.2.16 LR2 - AIS long-range reply sentence 2 (output)
- B.2.17 LR3 - AIS long-range reply sentence 3 (output)
- B.2.18 LRF - AIS long-range function (input / output)
- B.2.19 LRI - AIS long-range interrogation (input / output)
- B.2.20 NAK - Negative acknowledgement (output)
- B.2.21 PTHRAOC - AIS operational control (input / output)
- B.2.22 PTHRROS - Radio operational status (output)
- B.2.23 RMC - Recommended minimum specific GNSS data (input)
- B.2.24 ROT - Rate of turn (input)
- B.2.25 SPW - Security password sentence (input)
- B.2.26 SSD - AIS ship static data (input / output)
- B.2.27 THS -True heading and status (input)
- B.2.28 TRL - AIS transmitter non functioning log (output)
- B.2.29 TXT - Text transmission (output)
- B.2.30 VBW - Dual ground/water speed (input)
- B.2.31 VDM - AIS VHF data-link message (output)
- B.2.32 VDO - AIS VHF data-link own-vessel report (output)
- B.2.33 VER - Version (output)
- B.2.34 VSD - AIS voyage static data (input / output)
- B.2.35 VTG - Course over ground and ground speed (input)
- B.2.36 ZDA - Time and Date (output)
- Supported keys
- Glossary
- Index
Alarms and notifications
6-6 Chapter 6: Service & maintenance 98-137573-A
Rx channel
AIS 2
malfunction
(ID 004)
The SAILOR
6282 AIS
Transponder
stops
transmitting on
the affected
channel.
If continuous monitoring
of the receiver channel 2
shows inconsistency, this
alarm is activated.
Check the VHF
antenna, plugs, and
cable to the AIS
Transponder.
Rx channel
70
malfunction
(ID 005)
The SAILOR
6282 AIS
Transponder
continues
operation, but
external channel
management is
not possible.
If continuous monitoring
of the receiver channels
shows inconsistency, this
alarm is activated.
Check the VHF
antenna, plugs, and
cable to the AIS
Transponder.
General
failure
(ID 006)
The SAILOR
6282 AIS
Transponder
stops
functioning. In
case of severe
software or
hardware failure,
this alarm is
activated.
Check the power
supply to the AIS
Transponder.
UTC sync
invalid
(ID 007)
The SAILOR
6282 AIS
Transponder
continues
operation using
indirect or
semaphore
synchronization.
If the internal GNSS
receiver cannot receive a
synchronization signal
from the satellites, this
alarm is activated.
Check the GNSS
antenna, plugs, and
cable to the AIS
Transponder.
Alarm Consequence Reason Remedy
Table 6-1: AIS Alarms (Continued)