User's Manual
Table Of Contents
- Safety summary
- Preface
- Training information
- About this manual
- Introduction
- Installation
- Interface description
- Configuration
- Service & maintenance
- Technical specifications
- NMEA sentences
- B.1 NMEA sentences used
- B.2 Sentence use reference
- B.2.1 ABK - AIS addressed and binary broadcast acknowledgement (output)
- B.2.2 ABM - AIS addressed binary and safety related message (input)
- B.2.3 ACA - AIS channel assignment message (input / output)
- B.2.4 ACK - Acknowledge alarm (input)
- B.2.5 AIR - AIS interrogation request (input)
- B.2.6 ALR - Set alarm state (output)
- B.2.7 BBM - AIS broadcast binary message (input)
- B.2.8 DTM - Datum reference (input)
- B.2.9 EPV - Command or report equipment property value (input / response output)
- B.2.10 GBS - GNSS satellite fault detection (input)
- B.2.11 GGA - Global positioning system (GPS) fix data (input)
- B.2.12 GNS - Fix data (input)
- B.2.13 HBT - Heartbeat supervision sentence (input)
- B.2.14 HDT - Heading true (input)
- B.2.15 LR1 - AIS long-range reply sentence 1 (output)
- B.2.16 LR2 - AIS long-range reply sentence 2 (output)
- B.2.17 LR3 - AIS long-range reply sentence 3 (output)
- B.2.18 LRF - AIS long-range function (input / output)
- B.2.19 LRI - AIS long-range interrogation (input / output)
- B.2.20 NAK - Negative acknowledgement (output)
- B.2.21 PTHRAOC - AIS operational control (input / output)
- B.2.22 PTHRROS - Radio operational status (output)
- B.2.23 RMC - Recommended minimum specific GNSS data (input)
- B.2.24 ROT - Rate of turn (input)
- B.2.25 SPW - Security password sentence (input)
- B.2.26 SSD - AIS ship static data (input / output)
- B.2.27 THS -True heading and status (input)
- B.2.28 TRL - AIS transmitter non functioning log (output)
- B.2.29 TXT - Text transmission (output)
- B.2.30 VBW - Dual ground/water speed (input)
- B.2.31 VDM - AIS VHF data-link message (output)
- B.2.32 VDO - AIS VHF data-link own-vessel report (output)
- B.2.33 VER - Version (output)
- B.2.34 VSD - AIS voyage static data (input / output)
- B.2.35 VTG - Course over ground and ground speed (input)
- B.2.36 ZDA - Time and Date (output)
- Supported keys
- Glossary
- Index
Alarms and notifications
6-8 Chapter 6: Service & maintenance 98-137573-A
Active AIS-
SART
(ID 014)
The SAILOR
6282 AIS
Transponder
continues
operation.
This alarm is activated
when the SAILOR 6282
AIS Transponder receives
a position report from an
AIS search and rescue
transponder (SART). The
AIS SART indicates the
position of persons in
distress. It is displayed on
the first line in the AIS list
view on the SAILOR 6004
Control Panel.
External
EPFS lost
(ID 025)
The SAILOR
6282 AIS
Transponder
continues
operation, based
on the internal
GNSS.
The alarm is activated if
the external electronic
position fixing system
(EPFS) is lost.
Check the NMEA
connection
between the
external GNSS and
the AIS
Transponder.
No position
sensor in
use (ID 026)
The SAILOR
6282 AIS
Transponder
continues
operation.
The alarm is activated in
case none of the GNSS
connected to the AIS
Transponder provide valid
position data to the AIS
Transponder.
Check the GNSS
antenna, plugs, and
cable to the AIS.
Check the NMEA
connections
between the
external GNSS and
the AIS
Transponder. Check
the status of the
external GNSS at its
own control panel.
Check that the
GNSS antennas are
not covered and
are free to receive
satellite signals.
Alarm Consequence Reason Remedy
Table 6-1: AIS Alarms (Continued)