User's Manual
Table Of Contents
- Safety Summary
- Antenna Safety Instructions
- About the Manual
- Introduction
- Getting started
- Using the display and keypad
- Using the interfaces
- In this chapter
- General
- Bluetooth pairing
- Using a phone or fax machine
- Selecting the call type
- Connecting an analog phone or a fax machine
- Connecting an ISDN phone or a G4 fax machine
- Connecting a Bluetooth handset
- Entering the SIM PIN using a phone
- Making or receiving a phone call with the EXPLORER™ 700
- Making a call to the EXPLORER™ 700
- Dialing functions
- Sending or receiving a fax message
- Using a computer
- Additional interfaces
- What’s next?
- Using the web interface
- In this chapter
- Introduction
- The Home window
- Using the phone book
- Using the Call log
- Handling messages
- Setting up the EXPLORER™ 700
- Setting up the interfaces
- Enabling/disabling interfaces
- Description of data settings
- Configuring the USB interface
- Configuring the LAN interface
- Configuring the WLAN interface
- Configuring the Bluetooth interface
- Pairing Bluetooth devices from the web interface
- Configuring the Phone/Fax settings
- Configuring the ISDN interface
- Setting a common APN
- Properties, software upload and alarm list
- Administration
- Help desk and diagnostic report
- What’s next?
- Maintenance and troubleshooting
- Technical specifications
- In this appendix
- General specifications
- Battery
- Power input
- SIM interface
- Phone interface, 2-port
- ISDN interface, 2-port
- LAN interface, 2-port
- USB interface
- WLAN Access Point
- Bluetooth interface
- Antenna interface on Transceiver
- Detachable antenna
- EXPLORER™ Bluetooth Handset charger interface
- Solar panel interface
- I/O interface
- Serial number labels
- Conformity
- AT commands
- Glossary
- Index
Chapter 5: Using the web interface
98-122988-DraftB6 Setting up the interfaces 116
Pairing from your Bluetooth device
For information on how to pair devices from your Bluetooth device, see Pairing devices in which
you can enter a passkey on page 50.
Pairing devices with a fixed passkey
Some Bluetooth devices, such as headsets, do not provide the possibility to enter a passkey for
connecting to another device. These devices have a fixed passkey which must be entered on the
other device. This section describes how to pair such devices with the EXPLORER™ 700.
Do as follows to pair the devices:
1. Connect a computer to the EXPLORER™ 700, e.g. using the LAN interface.
2. Start up the EXPLORER™ 700.
Refer to Getting started on page 12.
3. Turn on Bluetooth on your Bluetooth device and place it close to the EXPLORER™ 700.
4. Access the web interface from your connected computer.
For further information, see The web interface on page 80.
5. Select SETTINGS > Interfaces > Bluetooth and make sure that Bluetooth is Enabled.
6. From the left menu of the Bluetooth window, select Add device.
Note that you can pair maximum 7 devices. If you have already paired 7 devices, you have to
unpair a device before you can pair a new one. For information on how to unpair devices, see
Unpairing devices on page 117.
7. Click Search.
The EXPLORER™ 700 now searches for Bluetooth devices.
8. Click Update.
9. When the device you want to pair appears in the list, click Pair next to the device.
10. Enter the passkey of your Bluetooth device.
The default passkey for a Bluetooth headset is often 0000. Otherwise, refer to the manual for
your Bluetooth device.
11. When you are prompted from the Bluetooth device, usually by a tone, press the button on the
device to accept pairing.
The new device should now be paired with the EXPLORER™ 700 and added to the list of Paired
devices. This list is accessed from the left menu of the Bluetooth window in the web interface.
Note
The method for pairing devices may vary depending on your Bluetooth device. Consult
your Bluetooth device documentation for information.
Note
The search procedure can take up to 2-3 minutes. The list is not updated
dynamically. Click Update to see new found devices.