User's Manual
Table Of Contents
- Safety Summary
- Antenna Safety Instructions
- About the Manual
- Introduction
- Getting started
- Using the display and keypad
- Using the interfaces
- In this chapter
- General
- Bluetooth pairing
- Using a phone or fax machine
- Selecting the call type
- Connecting an analog phone or a fax machine
- Connecting an ISDN phone or a G4 fax machine
- Connecting a Bluetooth handset
- Entering the SIM PIN using a phone
- Making or receiving a phone call with the EXPLORER™ 700
- Making a call to the EXPLORER™ 700
- Dialing functions
- Sending or receiving a fax message
- Using a computer
- Additional interfaces
- What’s next?
- Using the web interface
- In this chapter
- Introduction
- The Home window
- Using the phone book
- Using the Call log
- Handling messages
- Setting up the EXPLORER™ 700
- Setting up the interfaces
- Enabling/disabling interfaces
- Description of data settings
- Configuring the USB interface
- Configuring the LAN interface
- Configuring the WLAN interface
- Configuring the Bluetooth interface
- Pairing Bluetooth devices from the web interface
- Configuring the Phone/Fax settings
- Configuring the ISDN interface
- Setting a common APN
- Properties, software upload and alarm list
- Administration
- Help desk and diagnostic report
- What’s next?
- Maintenance and troubleshooting
- Technical specifications
- In this appendix
- General specifications
- Battery
- Power input
- SIM interface
- Phone interface, 2-port
- ISDN interface, 2-port
- LAN interface, 2-port
- USB interface
- WLAN Access Point
- Bluetooth interface
- Antenna interface on Transceiver
- Detachable antenna
- EXPLORER™ Bluetooth Handset charger interface
- Solar panel interface
- I/O interface
- Serial number labels
- Conformity
- AT commands
- Glossary
- Index
Chapter 3: Using the display and keypad
98-122988-DraftB6 43
Viewing terminal properties
You can view properties of the EXPLORER™ 700 such as IP address, hardware numbers, software
version and IMEI number. When contacting Support, please include these numbers.
To view the properties, select PROPERTIES > TERMINAL and select one of the following
options:
• IP ADDRESS to see the IP address of the EXPLORER™ 700. This IP address is used to
access the web interface of the EXPLORER™ 700. The web interface is a built-in web server
used to configure and set up the EXPLORER™ 700. For further information on the web
interface, see Using the web interface on page 80.
• HARDWARE to see the serial number, PCB numbers and MAC addresses of your
EXPLORER™ 700.
• MAC is the MAC address used for the LAN and Bluetooth interface.
• MAC WLAN is the MAC address used for the WLAN interface.
• SOFTWARE to see the software version of the EXPLORER™ 700.
• IMEI to see the IMEI number (International Mobile Equipment Identity) of the
EXPLORER™ 700. This is the unique mobile equipment number that identifies your
EXPLORER™ 700.
Viewing mobile subscriber numbers
If available on the SIM card, the MOBILE NUMBERS menu lists the mobile subscriber numbers
to use when calling the EXPLORER™ 700.
To view the mobile subscriber numbers, select
PROPERTIES > MOBILE NUMBERS.
If the mobile numbers are not available, the display reads
NO INFORMATION AVAILABLE.
Viewing the voice mail number
The EXPLORER™ 700 informs you of any incoming voice mail through the display and through the
web interface.
The voice mail number is the number you call to hear your incoming voice mail.
If available on the SIM card, the PROPERTIES menu shows the voice mail number.
To view the voice mail number, select
PROPERTIES > VOICE MAIL NUMBER.
If the voice mail number is not available, the display reads
NO INFORMATION AVAILABLE.
Note
There are two voice numbers, one for 3.1 kHz Audio and one for Standard Voice. For
further information, see Selecting the call type on page 51.