User's Manual
Table Of Contents
- Safety Summary
- Antenna Safety Instructions
- About the Manual
- Introduction
- Getting started
- Using the display and keypad
- Using the interfaces
- In this chapter
- General
- Bluetooth pairing
- Using a phone or fax machine
- Selecting the call type
- Connecting an analog phone or a fax machine
- Connecting an ISDN phone or a G4 fax machine
- Connecting a Bluetooth handset
- Entering the SIM PIN using a phone
- Making or receiving a phone call with the EXPLORER™ 700
- Making a call to the EXPLORER™ 700
- Dialing functions
- Sending or receiving a fax message
- Using a computer
- Additional interfaces
- What’s next?
- Using the web interface
- In this chapter
- Introduction
- The Home window
- Using the phone book
- Using the Call log
- Handling messages
- Setting up the EXPLORER™ 700
- Setting up the interfaces
- Enabling/disabling interfaces
- Description of data settings
- Configuring the USB interface
- Configuring the LAN interface
- Configuring the WLAN interface
- Configuring the Bluetooth interface
- Pairing Bluetooth devices from the web interface
- Configuring the Phone/Fax settings
- Configuring the ISDN interface
- Setting a common APN
- Properties, software upload and alarm list
- Administration
- Help desk and diagnostic report
- What’s next?
- Maintenance and troubleshooting
- Technical specifications
- In this appendix
- General specifications
- Battery
- Power input
- SIM interface
- Phone interface, 2-port
- ISDN interface, 2-port
- LAN interface, 2-port
- USB interface
- WLAN Access Point
- Bluetooth interface
- Antenna interface on Transceiver
- Detachable antenna
- EXPLORER™ Bluetooth Handset charger interface
- Solar panel interface
- I/O interface
- Serial number labels
- Conformity
- AT commands
- Glossary
- Index
Chapter 4: Using the interfaces
98-122988-DraftB6 Bluetooth pairing 50
Bluetooth pairing
What is pairing?
Bluetooth Pairing happens when two Bluetooth enabled devices agree to communicate with one
another. When this happens, the two devices exchange passkeys and join a pair. The pairing
process only takes place the first time the two devices are connected. Once the two devices have
established a pair, they automatically accept communication when one device recognizes the
other device.
Pairing devices in which you can enter a passkey
This section describes how to pair devices in which you can enter a passkey.
For information on pairing devices with a fixed passkey from your EXPLORER™ 700, see Pairing
Bluetooth devices from the web interface on page 115.
The following procedure presupposes that the EXPLORER™ 700 is configured to be visible to other
Bluetooth devices, and that the Bluetooth interface is turned on. For information on configuration,
see Configuring the Bluetooth interface on page 113.
Do as follows to pair the devices:
1. Start up the EXPLORER™ 700.
For further information, see Getting started on page 12.
2. Turn on Bluetooth on your Bluetooth device and place it close to the EXPLORER™ 700.
3. On your Bluetooth device, search for new devices and select the EXPLORER™ 700 when it is
found.
The default Bluetooth name of the EXPLORER™ 700 is EXPLORER 700.
If there is more than one EXPLORER™ 700 in the list, you can use the MAC address to locate
the correct one. To see the MAC address of your EXPLORER™ 700, enter the display menu
system and select PROPERTIES > TERMINAL > HARDWARE > MAC.
4. On your Bluetooth device, enter the passkey of your EXPLORER™ 700.
The default passkey is the serial number of your EXPLORER™ 700. To see the serial number,
look at the label on the back of your EXPLORER™ 700, or enter the menu system and select
PROPERTIES > TERMINAL > HARDWARE > UNIT SER. NO.
The new device is now paired and ready to communicate with the EXPLORER™ 700.
Note
The method for pairing devices may vary depending on your Bluetooth device. Consult
your Bluetooth device documentation for information.
Note
Maximum 7 devices can be paired with the EXPLORER™ 700. If you have already paired 7
devices you have to unpair a device before you can pair a new one. For information on
how to unpair devices, see Unpairing devices on page 117.