User's Manual

49
Installation
0544
Interfaces
Options Connections
VHF Signal Cable Connection Connection Signal description Ships cable
Options connector designation p/n 539603 box box 8 twisted pairs or
15-pin D-sub male
5m In from VHF External conn. overall screen
pin 1
VDR+ Brn
X1-1 X2-1 pair no. 1
pin 2 VDR- Brn/Wht X1-2 X2-2
pair no. 1
pin 3 AUX2 Orange X1-3 X2-3
pair no. 2
pin 4 AUX2 NO Orange/Wht X1-4 X2-4
pair no. 2
pin 5 AUX 1 Blue X1-5 X2-5
pair no. 3
pin 6 AUX 1 NO Blue/Wht X1-6 X2-6
pair no. 3
pin 7 int_Speaker + Grn X1-7 X2-7
pair no. 4
pin 8 int_Speaker - Grn/Wht X1-8 X2-8
pair no. 4
pin 9 DSC CALL Red X1-9 X2-9
pair no. 5
pin 10 DSC CALL NO Red/Wht X1-10 X2-10
pair no. 5
pin 11 GND
Blk+Blk/Wht
X1-11 X2-11 Equipment ground
pair no. 8
pin 12 NMEA + Yel X1-12 X2-12
pair no. 6
pin 13 NMEA - Yel/Wht X1-13 X2-13
pair no. 6
pin 14 DSC ALARM Purple X1-14 X2-14 pair no. 7
pin 15 DSC ALARM NO Purple/Wht X1-15 X2-15 pair no. 7
Housing Screen Chassis Chassis Screen Screens
Note 1:
Relay contact ratings (resistive load) Max. switched power: 30W or 60VA
Max. switched current: 1.0A
Max. switched voltage: 150VDC or 125VAC
in accordance with IEC61162-1
Correspondingly grouped individual cabling
NMEA data input from external
position sensor (see note 2)
Relay contact closing on incoming
Distress alert (see note 1)
Relay contact closing on incoming
DSC call (see note 1)
Note 2:
Following NMEA sentences are supported: GLL, RMC, ZDA, GGA, VTG, GNS
Mixed Rx/Tx audio output for
recording. Galvanically isolated,
balanced signal, 0dBm into 600Ω
VHF internal speaker output,
nom. 5W into 8Ω.
Relay contact closing on event pre
-
defined through service
programming (see note 1)
Relay contact closing on event pre
-
defined through service
programming (see note 1)
SPARC II Connections
VHF Signal Cable Extension box Extension box Cable integrated Extension box Signal description Ships cable
SPARC II connecto
r
designation p/n 56.114 In from VHF Out to CU1 with CU Out to CU2 8 twisted pairs
15-pin D-sub female
or conn. Box overall screen
pin 1 12.5VDC+ Red/W ht X2-1 X1-1 Red/Wht X3-1 Power to CUs pair no. 8
pin 2 DATA_+ Yel X2-2 X1-2 Yel X3-2 pair no. 1
pin 3 DATA_- Yel/Blk X2-3 X1-3 Yel/Blk X3-3 pair no. 1
pin 4 TX_AF+ Blu/Wht X2-4 X1-4 Blu/W ht X3-4 pair no. 2
pin 5 TX_AF- Blu X2-5 X1-5 Blu X3-5 pair no. 2
pin 6 GND Orange + Red X2-6 X1-6 Orange + Red X3-6 Equipment ground pair no. 6 & 8
pin 7 12.5VDC+ Orange/Wht X2-7 X1-7 Orange/Wht X3-7 Power to CUs pair no. 6
pin 8 RX_AF+ Grn/Wht X2-8 X1-8 Grn/Wht X3-8 pair no. 3
pin 9 RX_AF- Grn X2-9 X1-9 Grn X3-9 pair no. 3
pin 10 12.5VDC+ Blk/Wht X2-10 X1-10 Blk/Wht X3-10 Power to CUs pair no. 7
pin 11 EXT.Speaker + Brn X2-11 X1-11 Brn X3-11 pair no. 4
pin 12 EXT.Speaker - Brn/Wht X2-12 X1-12 Brn/Wht X3-12 pair no. 4
pin 13 GND Blk X2-13 X1-13 Blk X3-13 Equipment ground pair no. 7
pin 14 Lineout + Purple X2-14 X1-14 Purple (
NC
) X3-14 pair no. 5
pin 15 Lineout - Purple/Wht X2-15 X1-15 Purple/Wht (
NC
) X3-15 pair no. 5
Housing Screen Chassis Chassis Screen Chassis Screen
EXT LS
(VHF LS out: X5-1) CU1 LS out: X4-1 CU2 LS out: X6-1
EXT LS
(VHF LS out: X5-2) CU2 LS out: X4-2 CU2 LS out: X6-2
Connecting only one CU (CU1) and leaving jumpers J1/J2 in circuit provides VHF Ext. Speaker connection available at both X5-1/2 and X6-1/2.
VHF Ext. Speaker output will be available at terminals X5-1/2.
Rx-audio line output,
balanced signal, 0dBm
into 600Ω
External speaker
output, nom. 5W into
8Ω (
see NOTE
)
NOTE:
In case of connecting a second CU (CU2) to the Extension Box, jumpers J1/J2 should be removed in order to disconnect VHF
Ext. Speaker (VHF LS) output from terminals X6-1/2 and make available the CU2 Ext. Speaker (CU2 LS) connections instead.
SPARC II-bus Data
SPARC II-bus Tx audio
SPARC II-bus Rx audio
VHF radio external
speaker output, nom.
5W into 8Ω