5 Drawer Dresser Date of Purchase ___ / ___ / ___ Lot Number: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Easy WARNING ‐ Unit can tip over causing severe injury or death. ‐ Anchor unit to stud in wall (if instructed to). ‐ Do Not allow children to climb on unit. ‐ Put heavy items on lower shelves or drawers.
Helpful Hints PEOPLE NEEDED FOR ASSEMBLY: 1‐2 ESTIMATED ASSEMBLY TIME: 1 HOUR ‐ Open your item in the area you plan to keep it to avoid excessive heavy lifting. ‐ Identify, sort and count the parts before attempting assembly. ‐ Compression dowels are lightly tapped in with a hammer. ‐ Slides are labeled with a R (right) and L (left) for proper placement. ‐ Make sure to always face the point on the top of the Cam Lock towards the outer edge.
k Quic bly em Ass Ti p Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight. Failure to do so may result in stripping the screw.
Board Identification Not actual size C A E B Support Top F D Left Panel Upper Rail Bottom Right Panel I H J G Lower Rail x5 Drawer Front x2 Vertical Molding Y K x5 Drawer Bottom x5 Drawer Back Z x5 Left Drawer Side 4 x5 Right Drawer Side
Board Identification Not actual size This piece is paperboard construction. It is not made from wood, but is required for the assembly of your unit.
Part List 2 Actual Size 3 4 1 (x12) #A22570 cam lock (x12) #A22510 cam bolt (x6) #A22920 connector 8 7 (x50) #A11080 7/16" flat head 5 (x6) #A22910 connector bolt (x6) #A21660 wood dowel (x20) #A12120 7/16" pan head 11 9 (x20) #A11600 1‐1/4" flat head 6 10 (x8) #A12955 1‐1/8" flat head (x10) #A17100 7/16" bolt Not Actual Size (x32) #A21110 nail (x5) #A50515 Handle 13a Left Cabinet Member 15 13b Right Cabinet Member 13c Left Drawer Member 14c 14a 16 14d 13d 14b Right Drawer M
STEP 1 2 Quick 9 5 1 (x2) #A22570 (x4) #A22510 (x1) #A21660 (x4) #A12955 Assembly Tip 2 Proper orientation of CAM LOCK Attach all hardware as shown. Using four screws (9), attach the vertical molding (H) to the left panel (A) as shown. Please note, there are four pilot holes in the vertical molding (H) for attachment. 1 2 2 A 9 2 9 9 1 Do not get screws #8 & #9 mixed up. You will use the shorter of the two in this step.
STEP 2 13a 7 Left Cabinet Member (x15) #A11080 (x5) #A56770 Attached five left cabinet members (13a) to the left panel (A) with screws (7) as shown. 13a 13a 13a A 13a 13a 7 Marked with a "L".
STEP 3 2 Quick (x2) Assembly #A22570 Tip Proper orientation of CAM LOCK 9 5 1 (x4) #A22510 (x1) #A21660 (x4) #A12955 Attach all hardware as shown. Using four screws (9), attach the vertical molding (H) to the right panel (B) as shown. Please note, there are four pilot holes in the vertical molding (H) for attachment. 2 2 9 2 1 2 9 B 9 Do not get screws #8 & #9 mixed up. You will use the shorter of the two in this step.
STEP 4 13b 7 Right Cabinet Member (x15) #A11080 (x5) #A56770 Attach five right cabinet members (13b) to the right panel (B) with screws (7) as shown. 13b 13b 13b Marked with a "R".
STEP 5 2 14a 4 14b (x4) #A22510 (x3) #A22910 (x1) #A84050 14b Do not tighten this screw.
STEP 6 3 (x3) #A22920 3 F 3 3 You will need to tap the connector (3) with a hammer to fully insert. Be sure the connector is positioned as shown before pushing into hole.
STEP 7 Press the upper rail (F) onto the top (C) as shown so the connectors (3) engage the connector bolts (4). Turn the screw in the center of the connector (3) clockwise to lock in place. F C 3 Turn clockwise to lock in place.
STEP 8 3 4 1 (x4) #A22570 (x3) #A22920 5 (x3) #A22910 (x2) #A21660 Quick Assembly Tip You will need to tap the connector (3) with a hammer to fully insert. Be sure the connector is positioned as shown before pushing into hole.
STEP 9 Press the lower rail (G) onto the bottom (D) as shown so the connector bolts (4) engage the connectors (3). Turn the screw in the center of the connector (3) clockwise to lock in place. G D 3 Turn clockwise to lock in place.
STEP 10 1 (x4) #A22570 Quick 5 Assembly Tip (x2) #A21660 Proper orientation of CAM LOCK 5 1 1 E 5 16
STEP 11 UNLOCK LOCK Attach the bottom (D) and support (E) to the left panel (A) as shown. Turn the cam locks clockwise to lock in place.
STEP 12 UNLOCK LOCK B E A D 18
STEP 13 UNLOCK LOCK C B A 19
STEP 14 11 (x32) #A21110 IMPORTANT! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT AND MUST BE INSTALLED PROPERLY. With the help of another person, turn the unit over as shown. Position the back panel (S) as shown. Flush the bottom edge of the back panel with the edge of the bottom (D). Assure that the unit is square. Distance from corner to corner must be equal as shown. Nail straight into back edges as shown. 11 back panel notch S D Make sure edges are flush with each other.
STEP 15 16 (x10) #A54223 Lay the drawer sides down on a flat hard surface. Carefully line up the drawer bracket with the holes in the drawer side as shown. Using a hammer, tap each drawer bracket stem part way into the hole. Repeat this process until the drawer bracket is fully seated on the drawer side.
STEP 16 6 (x20) #A12120 You will be assembling five drawers. They all assemble in the same manner. Attach the left drawer side (Y) and right drawer side (Z) to the Drawer Front (I) with screws (6) as shown. Be sure the groove in the drawer sides are centered with the groove in the drawer front.
STEP 17 Slide the drawer bottom (K) into the groove of the drawer sides (Y&Z) and drawer front (I).
STEP 18 7 13c Left Drawer Member 8 13d (x20) #A11080 Right Drawer Member (x5) #A56770 Drawer Slide Kit (x20) #A11600 Marked with a "R". 8 7 13d 7 8 J Z 7 13c I Y x5 7 Marked with a "L".
STEP 19 10 15 (x10) #A17100 (x5) #A50515 10 Z 15 Y I x5 25
STEP 20 For Masonry, Concrete, or other wall materials: Consult your local hardware store for appropriate anchors to securely attach the safety bracket. 14c 14d (x1) #A84050 IMPORTANT: THIS UNIT MUST BE SECURE TO THE WALL TO HELP PREVENT TIPOVER. FOLLOW THESE INSTRUCTIONS TO INSTALL THE ANTI‐TIPPING SAFETY BRACKET PROVIDED WITH THIS PRODUCT. WARNING Serious or fatal crushing injuries can occur from furniture tipover.
STEP 21 Note: The drawer bracket holes are slotted. Drawer fronts can be adjusted by loosening screws, making needed adjustments and retightening screws.
Maximum Loads This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury. 50 lbs 22.6 kg 35 lbs 15.8 kg (each drawer) Warning: Risk of injury to persons ‐ do not place a television on this furniture. This furniture is not approved for use with a television. Certificate of Conformity 1. This certificate applies to the product identified by this instruction manual. 2.
Register your product to receive the following: * New trend details ‐ sneak peek on what's new * Surveys ‐ have a voice within our community * Exclusive deals and discount codes * Quick and easy replacement part service Visit your local retailer's website, rate your purchased product and leave us some feedback! We would like to extend a big "Thank You" to all of our customers for taking the time to assemble this product, and to give us your valuable feedback.
Español Cubierta Delantera Este libro de instrucciones contiene información IMPORTANTE de seguridad. Por favor lea y manténgalo para referencia en el futuro. No Regrese este producto! PRECAUCION Este mueble puede volcarse y causar graves heridas y/o muerte. Anclar el mueble a un poste de madera en la pared (si esto se requiere). No Permita que los niños monten el mueble. Mantenga los artículos más pesados en los cajones de abajo.
Español Página 7 Conecte todas las partes como se muestra. Con los cuatro tornillos (9), fije la moldura vertical (H) al panel izquierdo (A) como se muestra. Note por favor que hay cuatro agujeros piloto de fijación en el molde vertical (H). Vista del extremo No mezclar los tornillos #8 y #9. Se usará el modelo más corto de los dos para este paso. Página 8 Una las cinco partes de la cabina izquierda (13a) al panel izquierdo (A) con los tornillos (7) como aparece en la imagen.
Español Página 14 Tendrá que tocar el conector (3) con un martillo para insertarlo completamente. Asegúrese de que el conector esté colocado como se muestra antes de empujar en el orificio. Página 15 Presione el riel inferior (G) en la parte inferior (D) tal como se muestra para que los pernos de conexión (4) encajen en los conectores (3). Gire el tornillo en el centro del conector (3) en sentido horario para asegurarlo. Gire hacia la derecha para asegurarlo en su lugar.
Español Página 26 Para materiales de mampostería, hormigón u otros materiales de pared: Consulte con su ferretería local para obtener anclajes adecuados para fijar firmemente el soporte de seguridad. IMPORTANTE: ESTA UNIDAD DEBE ESTAR ASEGURADA SOBRE LA PARED PARA AYUDAR A PREVENIR VUELCOS. SIGA ESTAS INSTRUCCIONES PARA INSTALAR EL SOPORTE DE SEGURIDAD ANTI‐VUELCO SUMINISTRADO CON ESTE PRODUCTO. ADVERTENCIA Pueden ocurrir lesiones de aplastamiento grave o mortal al volcarse los muebles.
Español Página 28 CARGA MAXIMA Esta unidad ha sido diseñada para soportar la carga máxima anotada. El exceder estos límites puede causar inestabilidad, colapsarse y/o causar serias lesiones. ADVERTENCIA: Riesgo de lesiones a las personas ‐ no coloque un televisor sobre muebles. Este mueble no está aprobado para su uso con un televisor.
Français Couverture Avant CE LIVRET D'INSTRUCTION CONTIENT DES INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ. VEUILLEZ LIRE ET GARDER POUR UNE RÉFÉRENCE FUTURE Ne retournez pas ce produit! ATTENTION Le meuble peut basculer et causer des blessures graves ou la mort. Ancrer le meuble à une planche murale dans le mur (si indiqué). Ne laissez pas les enfants grimper sur le meuble. Placez les articles lourds sur les étagères ou dans les tiroirs inférieurs.
Français Page 7 Relier toutes les parties du meuble tel qu'illustré. À l'aide de quatre vis (9), fixer le moulage vertical (H) au panneau gauche (A) comme illustré. Remarque : le moulage vertical (H) comporte quatre trous pilotes de guidage pour fixation. Vue arrière Ne pas mélanger les vis n° 8 et n° 9. Vous utiliserez la plus courte des deux dans cette étape. Page 8 Joindre les cinq parties de gauche restantes de l'armoire (13a) au panneau gauche (A) à l'aide des vis (7) comme indiqué.
Français Page 14 Il est recommandé de taper sur le connecteur (3) avec un marteau pour l'insérer complètement. S'assurer que le connecteur soit positionné comme indiqué avant de l'introduire dans le trou. Page 15 Appuyer sur le rail inférieur (G) de la partie inférieure (D) tel qu'indiqué pour accrocher les boulons du connecteur (4) aux connecteurs (3). Tourner la vis centrale du connecteur (3) dans le sens horaire pour le verrouiller. Tourner dans le sens horaire pour verrouiller.
Français Page 26 Pour la maçonnerie, le béton ou d'autres matériaux de mur : Visiter votre quincaillerie locale pour obtenir des ancres appropriées qui permettront de fixer solidement le support de sécurité. IMPORTANT : CE MEUBLE DOIT ÊTRE SÉCURISÉ SUR LE MUR POUR ÉVITER QU'IL NE BASCULE. SUIVRE CES INSTRUCTIONS POUR INSTALLER LE SUPPORT DE SÉCURITÉ ANTI‐BASCULEMENT FOURNI AVEC CE PRODUIT. AVERTISSEMENT Des blessures graves ou mortelles peuvent se produire en cas de basculement des meubles.
Français Page 28 CHARGES MAXIMALES Ce meuble a été conçu pour supporter les charges maximales indiquées. En excédant ces limites de charge, le meuble pourrait devenir instable, s'effondrer, et/ou causer des blessures graves. AVERTISSEMENT : Risque de blessure corporelle ‐ ne pas placer une télévision sur ce meuble. Ce meuble n'est pas approuvé pour une utilisation avec une télévision.
