WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Night Stand NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 4 No. 2 Phillips Screwdriver Tip Shown Actual Size 5-23 Hammer Français 24-26 Español 27-29 Safety 30 Warranty 31 Page 2 Not actual size Skip the power trip. This time.
Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push six HIDDEN CAMS (1F) into the ENDS (A and B) and BACK (D). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow 1F D (6 used) 2F B Arrow A Insert the metal end of the CAM DOWEL into the HIDDEN CAM.
Step 2 å Push twenty-eight HIDDEN CAMS (1F) into the BOTTOM (G), SKIRTS (H and J), and the remaining holes of the ENDS (A and B) and BACK (D). Just think. The sooner you do this, the sooner you do something else. Arrow 1F (28 used) J J H H G Arrow 1F Arrow 1F D Arrow 1F B Arrow A Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
Step 3 å å NOTE: Position the LEGS (E and F) exactly as shown. å NOTE: One set of LEGS (E and F) receives four CAM SCREWS each. The other set of LEGS will have six CAM SCREWS each. Turn twenty-eight CAM SCREWS (8F) into the exact holes shown in the LEGS (E and F) and SKIRTS (H and J).
Step 4 å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. å å NOTE: Do not overtighten the SCREWS. å å NOTE: The MOLDINGS should be centered on the ENDS. Slide the END MOLDINGS (M) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS. NOTE: If the MOLDING comes up off of the SCREWS, remove it and slide it on again.
Step 5 å Insert one WOOD DOWEL (15F) into the RIGHT FRONT/LEFT REAR LEG (E) with four CAM SCREWS. å å NOTE: Be sure to use the exact hole shown. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the RIGHT END. å Fasten one of the SHORT SKIRTS (J) to the RIGHT FRONT/ LEFT REAR LEG (E). Tighten one HIDDEN CAM. 1 Fasten the RIGHT END (A) to the RIGHT FRONT/LEFT REAR LEG (E). Tighten two HIDDEN CAMS. The CAM SCREWS are closer to this edge.
Step 6 å Insert one WOOD DOWEL (15F) into the LEFT FRONT/RIGHT REAR LEG (F) with six CAM SCREWS. å å NOTE: Be sure to use the exact hole shown. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the RIGHT END. Fasten the LEFT FRONT/RIGHT REAR LEG (F) to the RIGHT END (A) and SHORT SKIRT (J). Tighten three HIDDEN CAMS. F 15F A J These surfaces should be even.
Step 7 å Insert one WOOD DOWEL (15F) into the LEFT FRONT/RIGHT REAR LEG (F) with four CAM SCREWS. å å NOTE: Be sure to use the exact hole shown. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the LEFT END. å Fasten the remaining SHORT SKIRT (J) to the LEFT FRONT/ RIGHT REAR LEG (F). Tighten one HIDDEN CAM. Fasten the LEFT END (B) to the LEFT FRONT/RIGHT REAR LEG (F). Tighten two HIDDEN CAMS. B Edge with CAM DOWELS The CAM SCREWS are closer to this edge.
Step 8 å Insert one WOOD DOWEL (15F) into the RIGHT FRONT/LEFT REAR LEG (E) with six CAM SCREWS. å å NOTE: Be sure to use the exact hole shown. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the LEFT END. Fasten the RIGHT FRONT/LEFT REAR LEG (E) to the LEFT END (B) and SHORT SKIRT (J). Tighten three HIDDEN CAMS. E 15F B J These surfaces should be even.
Step 9 å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
Step 10 å Fasten the LONG SKIRTS (H) to the long edges of the BOTTOM (G). Tighten four HIDDEN CAMS. å NOTE: The LONG SKIRTS are slightly shorter than the long edges of the BOTTOM so the edges of the parts will not be even. Now might be a good time to refresh your drink. Long edge H These edges are not even. G H Page 14 ith S e w CAM c a N f Sur IDDE H The CAM SCREWS are closer to this edge.
Step 11 å Insert one WOOD DOWEL (15F) into the LEFT FRONT/RIGHT REAR LEG (F) that is fastened to the RIGHT END (A). å Fasten the BACK (D) to the LEFT FRONT/RIGHT REAR LEG (F). Tighten two HIDDEN CAMS. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the BACK.
Step 12 å Fasten the BOTTOM (G) and LONG SKIRTS (H) to the LEGS (E and F) and SIDE SKIRT (J). Tighten four HIDDEN CAMS.
Step 13 å Insert one WOOD DOWEL (15F) into the RIGHT FRONT/ LEFT REAR LEG (E) that is fastened to the LEFT END (B). å Fasten the LEGS (E and F) and SHORT SKIRT (J) to the BACK (D), BOTTOM (G), and LONG SKIRTS (H). Tighten six HIDDEN CAMS. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the BACK.
Step 14 å Fasten the ENDS (A and B) and BACK (D) to the TOP (C). Tighten six HIDDEN CAMS. D A B C es hol h t i ce w a f r Su Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 15 å å Carefully stand your unit upright. Peel APPLIQUES from the APPLIQUE CARD (35P) and stick them onto each unused hole in the FRONT LEGS (E and F). F E 35P (6 used) To cover the unused holes in the LEGS.
Step 16 1 12S 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. BROWN 1" FLAT HEAD SCREW (2 used in this step) D12 L K D13 L å Fasten the DRAWER FRONT (L) to the DRAWER FRONT MOLDING (K). Use two BROWN 1" FLAT HEAD SCREWS (12S). å NOTE: Do not overtighten the SCREWS into the DRAWER FRONT MOLDING. 3 With the palm of your hand, tap the DRAWER BOTTOM down into the groove.
Step 17 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D12 and D13). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å å NOTE: The glides are not intended to rotate. Fasten the DRAWER RIGHT (35AC) to the RIGHT DRAWER SIDE (D12) and the DRAWER LEFT (35AD) to the LEFT DRAWER SIDE (D13). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. Almost time to celebrate! With a nap. Fasten two KNOB SETS (157K) to the DRAWER FRONT (L).
Step 18 å To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. WARNING Children have died from furniture tipover. To reduce the risk of furniture tipover: • ALWAYS install tipover restraint provided. • NEVER put a TV on this product. • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves. • NEVER open more than one drawer at a time.
Step 19 å To make adjustments to the drawer, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed. Tighten the SCREW when finished with adjustments.
LISTE DE PIÈCES REFERENCE Page 24 DESCRIPTION QUANTITÉ LISTE DE PIÈCES REFERENCE DESCRIPTION QUANTITÉ A EXTRÉMITÉ DROITE ..................................................1 35AA GLISSIÈRE D'ÉLÉMENT UNIVERSELLE.....2 B EXTRÉMITÉ GAUCHE ...............................................1 35AC TIROIR DROIT .................................................................1 C DESSUS ...............................................................................1 35AD TIROIR GAUCHE....................
ÉTAPE 1 ÉTAPE 5 (SUITE) Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. REMARQUE : S’assurer de bien insérer la CHEVILLE EN BOIS du PIED dans l’EXTRÉMITÉ DROITE. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer l’une des PLINTHES COURTES (J) au PIED AVANT DROIT/ ARRIÈRE GAUCHE (E). Serrer un EXCENTRIQUE ESCAMOTABLE. Enfoncer six EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B) et l’ARRIÈRE (D).
ÉTAPE 10 ÉTAPE 16 Fixer les LONGUES PLINTHES (H) sur les bords longs du DESSOUS (G). Serrer quatre EXCENTRIQUES ESCAMOTABLES. 1 Fixer le DEVANT DE TIROIR (L) à la MOULURE DE DEVANT DE TIROIR (K). Utiliser deux VIS TÊTE PLATE 25 mm MARRON (12S). REMARQUE : Ne pas trop serrer les VIS dans la MOULURE DE DEVANT DE TIROIR. 2 Insérer les CÔTÉS DE TIROIR (D12 et D13) en biseau dans la fente dans chaque extrémité du DEVANT DE TIROIR (L).
LISTA DE PARTES ITEM DESCRIPCIÓN CANTIDAD LISTA DE PARTES ITEM DESCRIPCIÓN CANTIDAD A EXTREMO DERECHO ...............................................1 35AA RIEL UNIVERSAL DE GABINETE ....................2 B EXTREMO IZQUIERDO ............................................1 35AC CAJÓN DERECHO ......................................................1 C PANEL SUPERIOR .......................................................1 35AD CAJÓN IZQUIERDO ...................................................
PASO 1 PASO 5 (CONTINUACIÓN) No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije uno de los FALDONES CORTOS (J) a la PATA DERECHA DELANTERA / PATA IZQUIERDA POSTERIOR (E). Apriete un EXCÉNTRICO ESCONDIDO. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje seis EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A y B) y el DORSO (D).
PASO 10 PASO 16 (CONTINUACIÓN) Fije los FALDONES LARGOS (H) sobre los bordes largos del FONDO (G). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. NOTA: Los FALDONES LARGOS son ligeramente más cortos que los bordes largos del FONDO por lo que los bordes de las partes no quedarán alineados. NOTA: No apriete en exceso los TORNILLOS en la MOLDURA DE CARA DE CAJÓN. 2 Inserte los LADOS DE CAJÓN (D12 y D13) en ángulo dentro del encaje en cada extremo de la CARA DE CAJÓN (L).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers or shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
5-YEAR LIMITED WARRANTY 1. We provides limited warranty coverage to the original purchaser of this product for a period of fi ve years from the date of purchase against defects in materials or workmanship of furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state. 2.
