ASSEMBLY INSTRUCTION SERVER Hex Bolt 5/16" x 2 1/2" 12 pcs Flat Washer M8 x 16mm 12 pcs Spring Washer 5/16" 12 pcs Wrench 1 pc This page lists all the contants included in the box. Please take the time to identify the hardware as well as the individual components to this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
ITurn the Server (A) upside down on a protective surface such as carpet or other soft material. Remove the square block which screw at the four corner of Server Top. Turn the screw anti-clockwise. See diagram below. 2J Turn the Server (A) upside down and place it on a piece of cloth to prevent from scratching. Attached Leg (C) to the back corner block of Server (A) . Tighten the Legs (C) with Flat Washer (E), Spring Washer (F) and Hex Bolt (D) and tighten it using Wrench (G).
^ Align the holes of Shelf (B) corner block to the Server Leg (C). Tighten the Shelf (B) with Flat Washer (E), Spring W asher (F) and Hex Bolt (D) and tighten it using Wrench (G). Repeat Step 2 and 3 to the other Legs (C). CLEANING & CARE Treat surface with care. Surface is resistant to scratches but is not scratches resistant. Clean surface with a dry or dampsoft cloth. Do not use abrasive cleaners. Hardware may loosen overtime. Priodicaliy check that all connections are tight.
ASSEMBLY INSTRUCTION SERVER □ Server Top Shelf f ^ l Leg Center Vertical Panel Right Left 't r □ I pc I pc Wine Rack (Vertical) Wine Rack (Horizontal) □ Hex Bolt 5/16"x 2 1/2" JCBC Bolt M6x40MM n f j^ ■ " Flat Washer M8x16MM 20 pcs Bottom Leg Support p U i Spring Washer 5/16" 20 pcs Wooden Dowel 010 X 30mm Allen Key 1 J.I i>, I pc 2 pcs Back Panel 8 pcs 12 pcs P Wrench 12.8mm 4 PCS 4 pcs I pc This page lists all the contants included in the box.
Turn The Server (A) upside down on a protective surface such as carpet or other soft material. Remove the square block which screw at the four corner of Server Top. Turn the screw anti-clockwise. See diagram below. Insert Left & Right Center Vertical Panel (D) following the picture below and tighten it with Flat Washer (K), Spring Washer (L) and JCBC Bolt (J) using Allen Key (N). Push in the Back Panel (G) . Then insert V'ooden Dowel (O) at the bottom of both Center Vertical Pane' (D).
□ Aligh the dowel holes on the Shelf (B) to the dowel at the Center Vertical Panel (D), then tighten it with Flat Washer (K), Spring Washer (L) and JCBC Bolt (J) using Allen Key (N). 4X 5^ Place the Leg (C) to the com er of Apron and tighten it with Flat Washer (K), Spring W asher (L) and Flex Bolt (I) using Wrench(M). Repeat the same to the other Legs. Insert and turn the Hanger Bolt of Bottom Leg Support (H) to the holes at the center of Shelf (B). Adjust the leveler to level the unit.
ASSEMBLY INSTRUCTION SERVER □ Server Top Shelf f ^ l Leg Center Vertical Panel r^n Right Left ''S i r I pc I pc Wine Rack (Vertical) □ Wine Rack (Horizontal) □ JCBC Bolt M6 x 40MM Hex Bolt 5/16" x 2 1/2" Back Panel Flat Washer M8 x 16MM n 20 pcs Bottom Leg Support □ Spring Washer 5/16" 20 pcs Wooden Dowel 010 X 30mm Allen Key ¿2'^____ i z>___ I pc 2 pcs Hrtuituiwwmn 8 pcs 12 pcs Im|Wrench 12.8mm 4 PCS J 4 pcs I pc This page lists all the contants included in the box.
Turn The Server (A) upside down on a protective surface such as carpet or other soft material. Remove the square block which screw at the four corner of Server Top. Turn the screw anti-clockwise. See diagram below. Insert Left & Right Center Vertical Panel (D) following the picture below and tighten it with Flat Washer (K), Spring Washer (L) and JCBC Bolt (J) using Allen Key (N). Push in the Back Panel (G) . Then insert V'ooden Dowel (O) at the bottom of both Center Vertical Pane' (D).
□ Aligh the dowel holes on the Shelf (B) to the dowel at the Center Vertical Panel (D), then tighten it with Flat Washer (K), Spring Washer (L) and JCBC Bolt (J) using Allen Key (N). 4X 5^ Place the Leg (C) to the com er of Apron and tighten it with Flat Washer (K), Spring W asher (L) and Flex Bolt (I) using Wrench(M). Repeat the same to the other Legs. Insert and turn the Hanger Bolt of Bottom Leg Support (H) to the holes at the center of Shelf (B). Adjust the leveler to level the unit.
