Installation & Assembly

ManualsBrandsThree Posts Manuals6 Seat Kitchen & Dining TablesCallisburg Rubber Solid Wood Dining Table

ASSEMBLY INSTRUCTION

RECTANGULAR DINING TABLE

__________________

ES TABLE TOP m TRESTLE LEG a BASE

1 PC

_____________

2 PCS

_____________

2 PCS

________

EH LOWER TRESTLE BAR EH SUPPORT BAR H ALLEN WRENCH

1 PC 2 PCS 1 PC

IJJCB C M6 x 80MM | | SPRING WASHER M6 0F L A T WASHER M6

(Included 8 pcs from step 1) (Included 8 pcs from step 1)

14 PCS 38 PCS 16 PCS

llSJcSK SCREW M4 x 38MM |fi| WOOD BUTTON S J LEVELER

Q> 0™ °

5 PCS 6 PCS 4 PCS

If] UPPER TRESTLE BAR

1 PC

“EST JCBC M6 x 40MM

(Included 8 pcs from step 1)

24 PCS

IflPVC DOWEL M8 x 30MM

2 PCS

This Page lists all the contents included

in the box . Please take the time to

identify the hardware as

well as the individual components to this

product. As you unpack and prepare for

assembly, place

the contents on a carpeted or padded

area to protect them from damage .

Summary of content (4 pages)

PAGE 1
ASSEM BLY INSTRUCTION RECTANGULAR DINING TABLE ES TABLE TOP m TRESTLE LEG 1 PC_____________ __________________ a 2 PCS_____________ EHLOWER TRESTLE BAR EHSUPPORT BAR If] UPPER TRESTLE BAR BASE 2 PCS________ H ALLEN WRENCH 1 PC “ESTJCBC M6 x 40MM (Included 8 pcs from step 1) 1 PC IJJC B C M6 x 80MM 14 PCS llSJcSKSCREW M4 x 38MM 2 PCS | | SPRING WASHER M6 (Included 8 pcs from step 1) 1 PC 0 F L A T WASHER M6 (Included 8 pcs from step 1) 38 PCS |fi| WOOD BUTTON 16 PCS 2 PCS S J LEVELER 0
PAGE 2
1 Please unloose 8 pcs bolt and spring washer and flat washer from the support bar(F) with Allen wrench(G). Keep the hardware for step 5 use and support bar for step 3 use. i) Insert pvc dowel(L) to both end of lower trestle bar(E). ii) Align and fasten upper trestle bar(D) with sticker arrow as shown below and lower trestle bar(E) to trestle leg(B) using long bolt(I) and spring washer(J) and tighten with Allen wrench(G). Insert wood button(N) to cover the open hole of the leg.
PAGE 3
Align and fasten support bar(F) to trestle leg(B) using short bolt(H) and spring washer(J). Please follow the ARROW sticker direction as shown below. ** Do not fully tighten the nut or bolt until all nuts and bolts are attached. long bolt(I) and spring washer(J).Tighten bolts with Allen wrench(G). Screw in the leveler(O) to bottom base. ** Do not fully tighten the nut or bolt until all nuts and bolts are attached.
PAGE 4
5 i) Place table top upside down on soft surface. Align and fasten support bar to table top using short bolt(H), spring washer(J) and flat washer(K) and fully tighten with Allen wrench(G). Which unloose from step 1 and tighten with Allen wrench(G). ii) Align and fasten upper trestle bar(D) to table top(A) using screw(M) and fully tighten with screw driver (Not Included). ** Do not fully tighten the nut or bolt until all nuts and bolts are attached.