LOW STORAGE CABINET 1/15
/15
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION PARTS DESCRIPTION BL A BR Fro nt / Ava nt Fro nt / Ava nt nt Ava nt / o r F TOP QTY 1 LEFT SIDE QTY 1 C RIGHT SIDE QTY 1 E D Fro nt / Ava nt Fro nt / Ava nt DIVIDER QTY 1 BOTTOM SHELF QTY 1 FR FL LEFT DOOR QTY 1 GR GL RIGHT DOOR QTY 1 CABINET SHELF QTY 2 LEFT BACK QTY 1 RIGHT BACK QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service 5/15
PRE-ASSEMBLY INFORMATION HARDWARE DESCRIPTION 1 2 ALLEN KEY SCREW M6 X 30 mm QTY 12 4 3 5 6 PHILLIPS SCREW ROUND HEAD M4 X 15 mm QTY 18 ALLEN KEY QTY 1 7 PHILLIPS SCREW M3 X 12 mm QTY 12 PHILLIPS SCREW M3 X 15 mm QTY 8 11 HANDLE M4 X 15 mm QTY 2 SETS SHELF SUPPORT QTY 12 9 8 10 WOOD DOWEL Ø8 X 30 mm QTY 10 CAM LOCK PIN CAM LOCK QTY 6 SETS a. M4 X 25 - QTY 2 ( 1 is extra ) b. M4 X 15 - QTY 1 c.
COMPONENTS – KEY DIAGRAM Fron t/A van t BL GR GL BR FR FL Fron t/A van t Fron t/A van t Fron t/A van t 7/15
ASSEMBLY Front / Avant Front / Avant STEP 1 1. Insert 2 Dowels 3 into pre-drilled holes on Divider C . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Attach Divider C to Bottom Shelf D using 3 Allen Key Screws 1 through predrilled holes. 4. Use Allen Key 4 to tighten screws. Do not over-tighten.
ASSEMBLY Front / Avant STEP 2 Front / Avant Front / Avant Front / Avant BR BL 1. Insert 4 Dowels 3 into pre-drilled holes on Bottom Shelf D ( 2 dowels / each side ). 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Attach 3 Cam Lock Pins 2 to each Side BL , BR into guide holes. 4. Align and insert Cam Lock Pins on Sides BL , BR into pre-drilled holes on Bottom Shelf D . 5. Place 6 Cam Locks 2 into pre-drilled holes on Bottom Shelf D . 6.
ASSEMBLY Front / Avant BR Front / Avant Front / Avant Front / Avant BL Front / Avant STEP 3 1. Insert 2 Dowels 3 into top corners of each Side BL , BR . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Align pre-drilled holes bottom corners of Top A with Dowels 3 in Sides BL , BR . 4. Attach Top A to Sides BL , BR and Divider C using 9 Allen Key Screws 1 . 5. Use Allen Key 4 to tighten screws. Do not over-tighten.
ASSEMBLY STEP 5 NOTE: The screwdriver is not included in the hardware pack. Fro nt / Ava nt FR BR Fro nt / Ava nt BL Fro nt / Ava nt Fro nt / Ava nt FL 1. Attach Hings on Doors F to Sides BL , BR using Phillips Screws 7 into pre-drilled guide holes. 2. Attach Magnet Plates 9 to bottom corner of Doors FL , FR using Phillips Screws 8 . into guide holes on Doors FL , FR . 3. Attach Magnets 9 to Bottom Shelf D using Phillips Screws 8 into guide holes on Bottom Shelf D . 4.
ASSEMBLY STEP 6 FR BR BL FL FR BR BL FL 1. Use 4 Shelf Supports 6 for each Shelf Cabinet E in desired location. 2. 2 Shelf Supports 6 may be used on back top of each Shelf Cabinets E as a tipping restraint.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP 7 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. Drill a 3/16 inch hole in the wall.
WARRANTY Thank you for purchasing our product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line or by email We reserve the right to repair or replace the defective product, at its discretion.
