Installation & Assembly

IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. Dry with a lint-free or microber cloth.
For Customer Service, contact
the place of purchase
Smooth / Black /
Transparent (L)
Black (Hot)
Ribbed / White /
Transparent (N)
Bare Copper / Transparent with
Green Interior / Green
White (Neutral)
Green
(Ground)
PREPARING FOR INSTALLATION
Carefully remove all of the contents from the carton. See the important notes
above. Shut off the power at the circuit breaker and completely remove the old
xturefromtheceiling,includingtheoldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.Oneendofnipple
(F)shouldbeattachedtomountingstrap(A)withwasherandhexnuts(C,D)in
place. The other end should have canopy loop (H) attached. Match the threaded
holesofmountingstrap(A)tothespacingoftheholesonthejunctionbox.
Attachmountingstrap(A)tothejunctionboxusingmountingscrews(B)and
ascrewdriver.Tightensecurely.Unscrewcanopyloopcollar(I)fromcanopy
loop(H).Passcanopy(G)overthemountedcanopylooptotesttheheight.
Approximatelyhalfofthecanopyloop’sexteriorthreadsshouldbeexposed,and
thecanopyloopcollarshouldtsnuglyontothecanopyloop.Removecanopy
(G)andadjusttheheightofnipple(F)andcanopyloop(H)untilthedesiredheight
is reached.
ASSEMBLING THE FIXTURE
Pull the wires until taut and carefully screw top loop (L) onto the threads of post at
thetopofxturebody(M).Bymeasuring,determinethecorrectnumberofchain
linksneededforproperhangingheight.Ifnecessary,useapairofplierstoopen
andremoveanyexcesschain.Attachonechainconnector(K)toeachendof
chain (J). Use one chain connector (K) to attach chain (J) to top loop (L) and close
thechainconnector.Feedthexture’swiresupthroughthechain(everythree
linksorso),pullingthewiresuntiltaut.Slidecanopyloopcollar(H)andcanopy
(G) onto the chain and wires. Use the free chain connector (K) to attach chain (J)
to canopy loop (H).
CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cut
awayexcesswire.Threadthexture’swiresthroughcanopyloopandnipple.
Attachthexture’swirestothepowersupplywiresfromthejunctionbox.
Connect black to smooth/black/transparent (L) wire; white to ribbed/white/
transparent(N)wire;groundtoground(greenorcopper).Twisttheendsofthe
wirepairstogether,andthentwistonawireconnector.Makesurealltwistsarein
thesamedirection.Ifthereisnogroundwire(greenorcopper)fromthejunction
box,locategroundscrew(E)onmountingstrap(A)andwrapthextureground
wirearoundthegreengroundscrew(E).Useascrewdrivertosecureground
screw(E)ontothemountingbracket/mountingstrap.Tuckallwiresneatlyintothe
junctionbox.
FINISHING THE INSTALLATION
Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)upbeneath
thecanopy.Tightlythreadcanopyloopcollar(I)ontocanopyloop(H)tosecure
canopy (G) in place.
Installbulb(notincluded)inaccordancewiththexture’sspecications.Donot
exceedthemaximumwattage.
M
K
K
J
L
I
H
B
F
G
D
C
E
A
Assembly Instructions