Installation & Assembly

ManualsBrandsThree Posts Manuals4 Seat Kitchen & Dining TablesHermitage Extendable Solid Wood Dining Table

ASSEMBLY INSTRUCTION

___________

) OVAL DINING TABLE WITH 18" EXTENSION LEAF ______________________

RS TABLE TOP 10 MOUNTING PLATE M PEDESTAL COLUMN ID PEDESTAL LEG

(Unloose from step 1) _

1 PC 1 PC 1 PC 4 PCS

1 0 ALLEN WRENCH t f JCBC M6 x 50mm [fl SPRING WASHER M6 |£ | FLAT WASHER M6

(Included 4 pcs from step 1) (Included 4 pcs from step 1) (Included 4 pcs from step 1)

r -" {¡¡f®0 &

1 PC

____________

6 PCS

____________

6 PCS_____________ 6 PCS

___________

1 1 WRENCH 13mm U HEX NUT 5/16" (O SPRING WASHER M8 |f l FLAT WASHER M8 x 2mm

1 PC 12 PCS 12 PCS 12 PCS

m LEVELER

4 PCS

This Page lists all the contents included

in the box . Please take the time to

identify the hardware as

well as the individual components to this

product. As you unpack and prepare for

assembly, place

the contents on a carpeted or padded

area to protect them from damage .

Summary of content (4 pages)

PAGE 1
ASSEM BLY INSTRUCTION ___________ ) OVAL DINING TABLE WITH 18" EXTENSION LEAF RS TABLE TOP 10 1 PC 1 0 ALLEN WRENCH [ f l SPRING WASHER M6 (Included 4 pcs from step 1) {¡¡f®0 & m U 6 PCS____________ HEX NUT 5/16" ID PEDESTAL LEG 1 PC t f JCBC M6 x 50mm (Included 4 pcs from step 1) 1 PC____________ 1 PC M PEDESTAL COLUMN _ 1 PC r -" 1 1 WRENCH 13mm MOUNTING PLATE (Unloose from step 1) ______________________ 4 PCS |£ | FLAT WASHER M6 (Included 4 pcs from step 1) 6 PCS_____________ (O SPRIN
PAGE 2
1 Please unloose bolt, spring washer and flat washer from mounting plate(B) with Allen wrench(E). Keep the hardware for step 3 use and mounting plate for step 2 use. Align and fasten mounting plate(B) to pedestal column(C) using hex nut(J), big spring washer(K) and big flat washer(L) and tighten with wrench(I). ** Do not fully tighten the nut or bolt until all nuts and bolts are attached.
PAGE 3
Place table top upside down on soft surface. Align and fasten mounting plate(B) to table top(A) using bolt(F), small spring washer(G) and small flat washer(H) and tighten with Allen wrench(E). ** Do not fully tighten the nut or bolt until all nuts and bolts are attached. E l Screw in the levelerfM) to the bottom of pedestal legfDF Align and fasten pedestal leg(D) to pedestal column(C) using hex nut(J), big spring washer(K), and big washer(L) and tighten with wrench(I).
PAGE 4
Flip table over using two people to lift and flip the table. Unlock the latches underneath table top(A). Pull apart the table top(A) at both ends and take out the center leaf. Push both ends together and make sure pin line up. Close the table top(A) tightly and lock all latches on the underneath of the table. A Stand table up on an even surface and check that it is balanced. If there is a slight wobble, please adjust the leveler. Cleaning & Care Treat Surface with care.