Assembly Instructions

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
CONNECTING THE WIRES
3.Attachthexture’swirestothepowersupplywiresfromthe
junctionbox.Connectblacktoblack(orsmooth);whitetowhite(or
ribbed);groundtoground(greenorcopper).Twisttheendsofthe
wirepairstogether,thentwistonawireconnector.Makesureall
twistsareinthesamedirection.Ifthereisnogroundwire(greenor
copper)fromthejunctionbox,locategroundscrew(E)onmounting
strap(A)andwrapthexture’sgroundwirearoundthegreenground
screw(E).Useascrewdrivertosecuregroundscrew(E)ontothe
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
For Customer Service, please
contact the place of purchase.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut off the power at the circuit breaker
and completely remove the old xture from the wall or ceiling, including the old mounting strap.
Please Note: This xture may be mounted on the wall or ceiling.
1.Mountingstrap(A)maybeattachedtobackplate(G).Ifthemountingstrapisattached,removescrews(B)todetach.The
mountingstrapcontainsseveralpairsofthreadedholes.Findthepairofholesthatmatchesthespacingoftheholesonthe
junctionboxandyourxture’sbackplate.Testbackplate(G)onmountingstrap(A)toensurethatthebackplatewillhang
straight.Placethextureaside.Gentlypullthehousewiresfromthejunctionboxthroughthecenterofmountingstrap(A).
2.Placemountingstrap(A)overthejunctionboxsothatmountingscrews(D)maybeinserted.Securemountingstrap(A)tothe
junctionboxwithmountingscrews(D)andascrewdriver.Tightenthemountingscrews(D)securely.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
FINISHING THE INSTALLATION
4.Placethexture’sbackplate(G)overmountingstrap(A)sothattheholesinmountingstrap(A)lineupwiththeholesinbackplate(G).
Usetheprovidedscrewdrivertothreadscrews(B)intobackplate(G)untilbackplate(G)issnugagainstthewallorceiling.
6.Installlightbulbs(notprovided)basedonthexture’sspecications.Donotexceedthemaximumwattage.
7.Slidemetalcages(H)uptothebottomofcaps(I).Securethemetalcagesinplacewithdecorativenuts(F).
Please note that you can move the light sources at joints (C) to adjust the direction of the light.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
F
A
D
B
C
E
H
G
G
N
D
I
Ceiling Installation
A
G
C
D
G
N
D
F
E
H
I
B
Wall Installation
Assembly Instructions