Owner Manual

ManualsBrandsThree Posts ManualsDesksOakside L-Shape Executive Desk with Hutch

For all your

newfangled gadgetry.

L-Desk

Summary of content (39 pages)

PAGE 1
For all your newfangled gadgetry.
PAGE 2
Table of Contents Part Identiﬁcation Hardware Identiﬁcation Assembly Steps Assembly Tools Required 3 4 No. 2 Phillips Screwdriver Tip Shown Actual Size 5-27 Hammer Français 28-31 Español 32-36 Safety 37-38 Warranty Page 2 39 Not actual size Skip the power trip. This time.
PAGE 3
Now you know our ABCs. Part Identiﬁcation å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identiﬁcation to help identify similar parts.
PAGE 4
Hardware Identiﬁcation å Screws are shown actual size. You may receive extra hardware with your unit.
PAGE 5
Step 1 å Assemble your unit on a carpeted ﬂoor or on the empty carton to avoid scratching your unit or the ﬂoor. å Push fourteen LARGE HIDDEN CAMS (1) into the LEFT END (O), DRAWER UPRIGHTS (P and Q), BACKS (R, S, and Y). Arrow (14 used) Arrow Q 1 1 P Y O Arrow R S 1 Arrow Arrow Hole 1 The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
PAGE 6
Step 2 å Turn fourteen ANGLED HEAD CAM SCREWS (3) into the LEFT DESK TOP (N), LEFT END (O), and HUTCH ENDS (X and V).
PAGE 7
Step 3 å å Flip the DRAWER UPRIGHTS over. å å Fasten the EXTENSION RAILS (FF) to the DRAWER UPRIGHTS (P and Q). Use six BLACK 1/2” PAN HEAD SCREWS (19). å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS. Separate the EXTENSION SLIDES (GG) from the EXTENSION RAILS (FF) as shown in the upper diagram. Be prepared, the parts are greasy. NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram.
PAGE 8
Step 4 å Fasten the LEFT BACK (R) to the LEFT END (O). Tighten the HIDDEN CAM.
PAGE 9
Step 5 å Insert four WOOD DOWELS (6) into the holes in the LEFT DESK TOP (N) as shown. å Fasten the LEFT END (O) and LEFT BACK (R) to the LEFT DESK TOP (N). Tighten ﬁve HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS insert into the LEFT BACK and LEFT END. å Insert four WOOD DOWELS (6) into the holes in the long edges of the LEFT BACK (R) and LEFT END (O).
PAGE 10
Step 6 å Insert six WOOD DOWELS (6) into holes in the LEFT DESK TOP (N) as shown. å Fasten the RIGHT BACK (S) and DRAWER UPRIGHTS (P and Q) to the LEFT DESK TOP (N). Tighten six HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS insert into the RIGHT BACK and DRAWER UPRIGHTS. å Insert six WOOD DOWELS (6) into the RIGHT BACK (S) and DRAWER UPRIGHTS (P and Q).
PAGE 11
Step 7 å Fasten the LARGE SHELF (L) to the DRAWER UPRIGHTS (P and Q) and LEFT END (O). Use eight SILVER 2" FLAT HEAD SCREWS (12). å NOTE: Be sure the WOOD DOWELS insert into the LARGE SHELF. Now might be a good time to refresh your drink.
PAGE 12
Step 8 å Fasten the RIGHT DESK TOP (M) to the RIGHT BACK (S) and LEFT BACK (R). Use eight SILVER 2" FLAT HEAD SCREWS (12). å NOTE: Be sure the WOOD DOWELS insert into the RIGHT DESK TOP.
PAGE 13
Step 9 å Fasten the TIE PLATE (8) to the LARGE SHELF (L) and RIGHT DESK TOP (M). Use four SILVER 5/8" PAN HEAD SCREWS (17). 17 SILVER 5/8" PAN HEAD SCREW (4 used in this step) 8 The ridges should be facing up.
PAGE 14
Step 10 å Fasten the SHORT BRACES (E1 and E2) to the LEFT LEG (B) and CENTER LEG (C). Use eight SILVER 5/16" MACHINE SCREWS (20). 20 SILVER 5/16" MACHINE SCREW (8 used in this step) This hole must be closer to the LEFT END (B). E2 This hole must be closer to the LEFT END (B).
PAGE 15
Step 11 å å Lay the LEG assembly on its back edge as shown. Fasten the SHELVES (K) to the LEFT LEG (B) and CENTER LEG (C). Use eight SILVER 1" FLAT HEAD SCREWS (15).
PAGE 16
Step 12 å å NOTE: You may need someone's help in this step. å NOTE: You should start each SCREW a few turns before completely tightening any of them. Fasten the LONG UPPER BRACES (H and I) and LONG LOWER REAR BRACE (J) to the RIGHT LEG (A) and REAR LEG (D). Use twelve SILVER 5/16" MACHINE SCREWS (20). 20 SILVER 5/16" MACHINE SCREW (12 used in this step) D I H J These holes must be here.
PAGE 17
Step 13 å Fasten the CENTER BRACES (G and F) to the LONG UPPER FRONT BRACE (H). Use four SILVER 5/16" MACHINE SCREWS (20). å Fasten the CENTER LEG (C) to the CENTER BRACES (G and F). Use four SILVER 5/16" MACHINE SCREWS (20). 20 SILVER 5/16" MACHINE SCREW (8 used in this step) This hole must be here. G H F These holes must be here.
PAGE 18
Step 14 å å NOTE: This is a two person step. å NOTE: You should start each SCREW a few turns before completely tightening any of them. Pro Tip: Lift with your legs. And, you know, your arms. Fasten the SHELF (L) and the RIGHT DESK TOP (M) to the SHORT BRACES (E1 and E2), CENTER BRACES (F and G) and LONG UPPER BRACES (H and I). Use twelve SILVER 1-3/8" FLAT HEAD SCREWS (14).
PAGE 19
Step 15 å Fasten the HUTCH SUPPORT (T) to the RIGHT END (A) and REAR LEG (D). Use four SILVER 1/2" MACHINE SCREWS (18).
PAGE 20
Step 16 å Insert two WOOD DOWELS (6) into holes in the HUTCH ENDS (V and X). å Fasten the HUTCH ENDS (V and X) to the HUTCH BACK (Y). Tighten two HIDDEN CAMS. å Insert two WOOD DOWELS (6) into the short edges of the HUTCH DIVIDERS (W). å Fasten the HUTCH DIVIDERS (W) to the HUTCH BACK (Y). Use two SILVER 2" FLAT HEAD SCREWS (12).
PAGE 21
Step 17 å å Flip up the HUTCH ENDS and HUTCH DIVIDERS. å Fasten the HUTCH SHELF (U) to the HUTCH ENDS (V and X), HUTCH DIVIDERS (W), and HUTCH BACK (Y). Use twelve SILVER 2" FLAT HEAD SCREWS (12). Insert six WOOD DOWELS (6) into the holes in the HUTCH SHELF (U) as shown.
PAGE 22
Step 18 å å NOTE: This is a two person step. Pro Tip: Lift with your legs. And, you know, your arms. Fasten the HUTCH SHELF (U) to the HUTCH SUPPORT (T). Use six SILVER 1-3/8" FLAT HEAD SCREWS (14).
PAGE 23
Step 19 å Turn four STRAIGHT HEAD CAM SCREWS (4) into the DRAWER FRONT (EE). å Push four SMALL HIDDEN CAMS (2) into the edges of the DRAWER SIDES (AA and Z) and DRAWER BRACE (DD). This hole will not be used in this step.
PAGE 24
Step 20 1 2 1 d he s i ﬁn Un face r su 2 CC AA AA DD DD Z Z EE EE Groove å Fasten the DRAWER SIDES (AA and Z) and DRAWER BRACE (DD) to the DRAWER FRONT (EE). Tighten four SMALL HIDDEN CAMS. å Slide the DRAWER BOTTOM (CC ) into the grooves in the DRAWER SIDES (AA and Z) and DRAWER FRONT (EE). 3 BB AA 13 SILVER 1-1/2" FLAT HEAD SCREW (4 used in this step) DD Z Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove.
PAGE 25
Step 21 å Fasten the EXTENSION SLIDES (GG) to the DRAWER SIDES (AA and Z). Use four BLACK 1/2" SMALL PAN HEAD SCREWS (19). å Fasten the KNOB (5) to the DRAWER FRONT (EE). Use a SILVER 7/8" MACHINE SCREW (16).
PAGE 26
Step 22 å Push the USB PORT (10) into the hole in the LEFT DESK TOP (N) threading the cord through one of the grommet holes as shown. å Push four GROMMETS and CAPS (9) into the large holes in the BACKS (R and S) and LEFT DESK TOP (N) as shown. This device complies with part 15 of the FCC Rules.
PAGE 27
Step 23 å To insert the drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. å å å å Push a CAM COVER (7) onto each visible HIDDEN CAM. Peel a screw cover from the SCREW COVER CARD (11) and center them over the heads of each screw.
PAGE 28
Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
PAGE 29
ÉTAPE 1 ÉTAPE 6 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Insérer six CHEVILLES EN BOIS (6) dans les trous du DESSUS DE BUREAU GAUCHE (N) comme l'indique le schéma. Enfoncer quatorze GRANDES EXCENTRIQUES ESCAMOTABLES (1) dans les chants de l'EXTRÉMITÉ GAUCHE (O), des MONTANTS DE TIROIR (P et Q) et des ARRIÈRES (R, S et Y). Fixer l'ARRIÈRE DROIT (S) et les MONTANTS DE TIROIR (P et Q) au DESSUS DE BUREAU GAUCHE (N).
PAGE 30
ÉTAPE 10 ÉTAPE 16 Fixer les ENTRETOISES COURTES (E1 et E2) au PIED GAUCHE (B) et au PIED CENTRAL (C). Utiliser huit VIS À MÉTAUX 8 mm ARGENT(20). Insérer deux CHEVILLES EN BOIS (6) dans les trous des EXTRÉMITÉS DE SURMEUBLE (V et X). ÉTAPE 11 Poser l’ensemble de PIED sur ses chants arrière comme l’indique le schéma. Fixer les TABLETTES (K) au PIED GAUCHE (B) et au PIED DROIT (C). Utiliser huit VIS TÊTE PLATE 25 mm ARGENT (15).
PAGE 31
ÉTAPE 20 ÉTAPE 22 1. Fixer les CÔTÉS DE TIROIR (AA et Z) et l’ENTRETOISE DE TIROIR (DD) au DEVANT DE TIROIR (EE). Serrer quatre PETITES EXCENTRIQUES ESCAMOTABLES. Enfoncer le PORT USB (10) dans le trou du DESSUS DE BUREAU GAUCHE (N) et enﬁlant le cordon à travers l'un des passe-câbles comme l’indique le schéma. 2. Enﬁler le FOND DE TIROIR (CC) dans les rainures des CÔTÉS DE TIROIR (AA et Z) et du DEVANT DE TIROIR (EE).
PAGE 32
Use estas instrucciones de ensamblaje en español junto con las ﬁguras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las ﬁguras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identiﬁcation” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PAGE 33
PASO 1 PASO 5 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Inserte cuatro PASADORES DE MADERA (6) en los agujeros del PANEL SUPERIOR DE ESCRITORIO IZQUIERDO (N) como se muestra. Empuje catorce EXCÉNTRICOS ESCONDIDOS GRANDES (1) dentro de los bordes del EXTREMO IZQUIERDO (O), los PARALES DE CAJÓN (P y Q) y de los DORSOS (R, S y Y). Fije el EXTREMO IZQUIERDO (O) al DORSO IAQUIERDO (R) y al PANEL SUPERIOR DE ESCRITORIO IZQUIERDO (N).
PAGE 34
PASO 9 PASO 15 Fije la PLACA DE CONEXIÓN (8) al ESTANTE GRANDE (L) y al PANEL SUPERIOR DE ESCRITORIO DERECHO (M). Utilice cuatro TORNILLOS PLATEADO DE CABEZA REDONDA de 16 mm (17). Fije el SOPORTE DE ORGANIZADOR (T) al EXTREMO DERECHO (A) y a la PATA POSTERIOR (D). Utilice cuatro TORNILLOS PLATEADO PARA METAL de 13 mm (18). PASO 10 PASO 16 Fije las RIOSTRAS CORTAS (E1 y E2) a la PATA IZQUIERDA (B) y a la PATA CENTRAL (C). Utilice ocho TORNILLOS PLATEADO PARA METAL de 8 mm (20).
PAGE 35
PASO 19 PASO 22 Atornille cuatro BIELAS DE EXCÉNTRICO CON CABEZA RECTA (4) en la CARA DE CAJÓN (EE). Empuje el PUERTO USB (10) en el agujero del PANEL SUPERIOR DE ESCRITORIO IZQUIERDO (N) y deslice el cable a través de uno de los ojales como se muestra. Empuje cuatro EXCÉNTRICOS ESCONDIDOS PEQUEÑOS (2) en los bordes de los LADOS DE CAJÓN (AA y Z) y la RIOSTRA DE CAJÓN (DD). PASO 20 1. Fije los LADOS DE CAJÓN (AA y Z) y la RIOSTRA DE CAJÓN (DD) a la CARA DE CAJÓN (EE).
PAGE 36
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
PAGE 37
AVERTISSEMENT Prière d’utiliser le mobilier à bon escient et avec prudence. Une mauvaise utilisation peut être à l’origine de risques d’accident ou peut endommager le mobilier et les articles ménagers. Lire attentivement le tableau suivant. À surveiller : Danger éventuel : Solution : • Tablettes et tiroirs surchargés. • En cas de chargement inadéquat l’élément peut être lourd du haut. • Risque de blessure. • Du mobilier mal équilibré risque de se renverser.
PAGE 38
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
PAGE 39
5-YEAR LIMITED WARRANTY 1. We provides limited warranty coverage to the original purchaser of this product for a period of ﬁ ve years from the date of purchase against defects in materials or workmanship of furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from state to state. 2.