Kitchen Cart/ Island
PART LIST F Left Panel Right Panel Top Panel Front Middle Rail Front Top Rail 1 PC 1 PC 1 PC 1 PC 1 PC Back Vertical Rail Bottom Panel Left Door Panel G H J Back Rail Back Panel 2 PCS 2 PCS 1 PC 1 PC 1 PC Right Door Panel Adjustable Shelf Drawer Front Panel Drawer Left Panel Drawer Right Panel 1 PC 1 PC 1 PC 1 PC 1 PC i$ � Drawer Back Panel Drawer Bottom Pane 1 PC 1 PC � Locking Caster Caster Towel Bar 2 PCS 2 PCS 2 PCS 2
HARDWARE LIST #1 Cam Lock Cam Bolt 12 PCS (Extra 2) 12 PCS #5 #4 #3 #2 #6 Allen Bolt Wood Dowel 16 PCS #7 4PCS #8 1-1/4"*(2'.
Step 1. Insert cam bolts (part #2) into left panel (part A), right panel (part B) and top panel (part C) using phillips head screwdriver. NOTE: Do not overtighten cam bolts. Stop tightening once threads on cam bolt are no longer visible. #2 #2 �X12 Step 2. Attach rails (parts D, E & F) to right panel (part B) using cam locks (part #1) and wood dowels (part #3). NOTE: Cam locks must rotate a full 180 ° . See pictured insert.
Step 3. Attach back vertical rail (part H) to back rail (part F) using wood dowels (part #3). Slide back panels (part G) into grooves of assembled unit (parts B, F & H). 0 #3 �X2 Step 4. Attach back rail (part F) to assembled unit (parts B, G & H) using cam lock (part #1) and wood dowels (part #3). NOTE: Cam locks must rotate a full 180 ° . See pictured insert.
Step 5. Attach left panel (part A) to assembled unit (parts D, E, F & G) using cam locks (part #1) and wood dowels (part #3). NOTE: Cam locks must rotate a full 180 ° . See pictured insert. I I I I I I I I I t#3 #3tI I I I I I I I I I t#3 I turn clockwise to fasten I I I I I .Iii I ...... • #1 ,.. .Iii . #1 D E #1 � X4 #3 �X4 Step 6. Carefully turn unit upside down on a soft flat surface, such as carpet, as shown below.
Step 7. CASTER INSTALLATION Attach locking casters (part R) and casters (part S) to bottom panel (part I) using large round head screws (part #11) and phillips head screwdriver. LEG INSTALLATION Do not install casters. Attach legs using instruction manual and hardware included inside leg packaging. #11 f X16 Step 8. Carefully turn unit upright. Attach towel bars (part T) to panels (parts A & B) using short allen bolts (part #5) and allen wrench (part #14 ).
Step 9. Attach top panel (part C) to assembled unit (parts A, B & F) using cam locks (part #1) and wood dowel (part #3). NOTE: Cam locks must rotate a full 180 ° . See pictured insert. adjacen � . ½ turn clockwise to fasten #1 � X4 #3 �X1 Step 10. Attach knobs (part #9) to door panels (parts J & K) using round head bolts (part #10) and phillips head screwdriver. Attach door panels (parts J & K) by placing bottom pin hinge (pre-installed in door) in the pre-drilled hole of bottom panel (part I).
Step 11. Attach knob (part #9) to drawer front panel (part M) using round head bolt (part #10) and phi I lips head screwdriver. Attach drawer panels (parts N & 0) to drawer front panel (part M) using screws (part #6) and phillips head screwdriver. Slide drawer bottom panel (part Q) into grooves of assembled unit (parts M, N & 0). Attach drawer back panel (part P) to assembled unit (parts N, 0 & Q) using screws (part #6) and phillips head screwdriver. NOTE: Be sure drawer glide wheels are facing back panel.
