PART LIST Left Vertical Panel [Right Vertical Panel Fixed Shelf Front Top Rail Left Panel 1PC 1PC 1PC 1PC 1PC Right Panel Back Rail Back Panel Middle Back Panel | Back Horizontal Rail 1PC PCS PCS 1PC PCS Bottom Panel Top Panel Left Door Panel Right Door Panel | Left Middle Door 1PC 1PC 1PC 1pC Sane! Right Middle Door | Adjustable Shelf | Middle Adjustable Support Rail Panel Shelf 1PC 4 PCS 1PC 1PC
HARDWARE LIST Cam Lock Cam Bolt Wood Dowel Screw Hex Socket Head Bolt 20 PCS (Extra 2) 20 PCS 42 PCS 7 PCS (Extra 1) 8 PCS Barrel Nut Shelf Holder Knob Round Head Bolt Magnet 8 PCS 20 PCS 4 PCS 4 PCS PCS (Spare Part) Double Magnet Round Head Allen Wrench Safety Strap Kit Pin Hinge Screw 1PC 6 PCS (Extra 1) 1PC 1 SET (Extra 4) ADDITIONAL TOOLS (Not Provided) Note: It is not recommended to use power tools during assembly. rd Phillips Head Screwdriver Note: Wood dowels are intended for alignment.
Step 1. Insert cam bolts (part #2) into left vertical panel (part A), right vertical panel (part B), left panel {part E), right panel (part F), bottom panel (part K) and top panel (part L) using fillips head screwdriver. NOTE: Do not over tighten cam bolts. Stop tightening once threads on cam bolt are no longer visible. Step 2. Attach left vertical panel (part A) and right vertical panel (part B) to fixed shelf (part C) using cam locks (part #1) and wood dowels (part #3).
Step 3. Carefully tum unit upright. Attach front top rail (part D) to assembled unit (parts A & B) using wood dowels (part #3), screws (part #4) and fillips head screwdriver. Step 4. Carefully turn unit upside down. Attach left panel (part E) to front top rail (part D) using cam lock (part #1) and wood dowel (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 5. Step 6. Attach back rail (part G) to left panel (part E) using cam lock (part #1) and wood dowel (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert. tum clockwise to fasten Place back horizontal rails (part J) into back rail (part G) using wood dowels (part #3). Slide back panels (part H) and middies back panel (part |) into the grooves of back horizontal rails {part J) and back rail (part G).
Step 7. Attach right panel (part F) to front top rail (part D) and back rails (part G) using cam locks (part #1) and wood dowels (part #3). Attach magnets (part #10) to front top rail (part D) and double magnet (part #11) to fixed shelf (part C) using round head screws (part #12) and fillips head screwdriver. NOTE: Cam locks must rotate a full 180°. See pictured insert. po She | lock toward adjacent hole A UJ Al tum clockwise to fasten #11.7x1 #127 x6 Step 8.
Step 8. Attach bottom panel (part K) to assembled unit (parts using cam lock (part #1), wood dowels (part #3), hex socket head bolts (part #5), barrel nuts (part #6) and Allen wrench (part #13). Attach legs using instruction manual and hardware included inside leg packaging. NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 10. Carefully tum unit upright. Attach top panel (part L) to assembled unit (parts using cam locks (part #1), wood dowels (part #3), screw (part #4) and fillips head screwdriver. NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 11. Attach knobs (part #8) to left door panel! (part M), right door panel (part N), left middle door panel (part O) and right middle door panel (part P) using round head bolts (part #9) and fillips head screwdriver. Attach left door panel (part M), right door panel (part N), left middle door panel (part O) and right middies door panel (part P) by placing bottom pin hinge (per-installed in door) in the per-drilled hole of bottom panel (part K).
Step 12. Place shelf holders (part #7) into desired position and then slide adjustable shelves (part Q) and middle adjustable shelf (part R) into place.
Dg*3a" Safety Strap Kit | Wall Anchor Washer Short Screw Long Screw 1ST 1PC 2PC8 1PC 1PC Safety Wall Strap 1PC SAFETY WALL STRAP INSTALLATION Note: It is highly recommended to install this safety strap kit to prevent tipping, damage and/or injury. — 1. Insert short screw (C) through washer (B) and safety wall pe strap {E) and attach to back of top panel (part L} using fillips head screwdriver. / 2. Drill a 11/32" hole where you want to secure the unit.
