Europe, Middle East ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ITALIANO ESPAÑOL PORTUGUÊS РУССКИЙ ΕΛΛΗΝΙΚΑ TÜRKÇE POLSKI اﻟﻌﺮﺑﻴﺔ North America/ Norteamérica ENGLISH FRANÇAIS ESPAÑOL Latin America/ América Latina ENGLISH ESPAÑOL PORTUGUÊS Asia Pacific 㗌㜓媅 䭧ἺḔ㕮 丨檻Ḕ㕮 한국어 ENGLISH
User Manual WARNING: To ensure that your T300 racing wheel functions correctly with games, you may be required to install the game’s automatic updates (available when your system is connected to the Internet).
TECHNICAL FEATURES 1 2 3 4 5 6 7 SELECT/START buttons on PS3™ and SHARE/OPTIONS on PS4™ 8 PS button 9 Large threaded hole (for attachment system and fastening screw) 10 Attachment system 11 Metal fastening screw T300 RS base T300 GT wheel 2 sequential paddle shifters (up & down) Directional buttons Built-in USB sliding switch for PS4™/PS3™ MODE button + red/green indicator light 12 Thrustmaster Quick Release 13 L3/R3 buttons 14 Power supply connector (type A or B) (varies from one country to another) 1
PLUGGING THE RACING WHEEL INTO AN ELECTRICAL OUTLET: PLEASE READ BEFORE PROCEEDING! Your racing wheel’s power supply varies according to the country where you purchased your device. The power supply can be: Internal, with: * a power supply unit located directly inside the racing wheel’s base, with a type A connector. * a 220-240 V power supply cable. = compatible only with 220-240 V electrical power.
WARNING Before using this product, please read this manual carefully and save it for later reference. Warning – Electrical shock Keep the product in a dry location and do not expose it to dust or sunlight. Do not twist or pull on the connectors and cables. Do not spill any liquid on the product or its connectors. Do not short-circuit the product. Never dismantle the product; do not throw it onto a fire and do not expose it to high temperatures.
Warning – Injuries due to force feedback and repeated movements (continued) * If the symptoms or pain indicated persist when you start playing again, stop playing and consult your doctor. * Keep out of children’s reach. * During gameplay, always leave both hands correctly positioned on the wheel without completely letting go. * During gameplay, never place your hands or your fingers under the pedals or anywhere near the pedal set.
Warning – Pedal set pinch hazard when playing * * * * Keep the pedal set out of children’s reach. During gameplay, never place your fingers on or anywhere near the sides of the pedals. During gameplay, never place your fingers on or anywhere near the pedal’s rear base. During gameplay, never place your fingers on or anywhere near the pedal’s front base. NEVER NEVER NEVER Warning – Pedal set pinch hazard when not playing * Store the pedal set in a safe place, and keep it out of children’s reach.
INSTALLING THE WHEEL ON ITS BASE Align the connector positions using the arrows: Base (1) connector: Arrow pointing upwards Racing wheel (2) connector: Arrow pointing upwards Once the connectors are correctly positioned, simply rotate the Thrustmaster Quick Release (12) device’s ring anticlockwise, while holding the racing wheel (2) in position. Then, tighten the ring as much as you can: to do so, hold the ring in position and rotate the racing wheel clockwise.
ATTACHING THE RACING WHEEL Attaching the racing wheel to a table or a desktop 1. Place the racing wheel on a table or any other horizontal, flat and stable surface. 2. Insert the fastening screw (11) in the attachment system (10), then tighten the device by turning the screw anticlockwise, so that it feeds into the large threaded hole (9) located beneath the racing wheel, until the wheel is perfectly stable.
ATTACHMENT / REMOVAL DIRECTION To tighten: Turn the screw anticlockwise To release: Turn the screw clockwise 9/24
Attaching the racing wheel’s base to a cockpit 1. Place the racing wheel’s base on the cockpit shelf. 2. Drive two M6 screws (not included) through the cockpit shelf, then feed them into the two small screw threads located on the underside of the racing wheel. Important: The length of the two M6 screws must not exceed the thickness of the shelf + 12 mm; longer screws could cause damage to internal components located in the racing wheel’s base. 3.
SETTING UP THE PLAYSTATION®4 RACING WHEEL FOR PLAYSTATION®3 OR 1. Connect the pedal set to the connector (17) located at the back of the racing wheel's base. 2. Connect the power supply cable to the connector (14) located at the back of the racing wheel's base. 3. Plug the power supply cable into an electrical outlet with the same voltage specifications. For more information about this, please refer to the PLUGGING THE RACING WHEEL INTO AN ELECTRICAL OUTLET section, on page 3 in this manual. 4.
SETTING UP THE RACING WHEEL FOR PC* * PC compatibility not tested nor endorsed by Sony Interactive Entertainment Europe. For more information, visit http://support.thrustmaster.com. AUTOMATIC RACING WHEEL AND PEDAL SET CALIBRATION The wheel automatically self-calibrates when you plug the racing wheel into an electrical outlet and connect the racing wheel’s USB connector to the system.
MODE BUTTON AND INDICATOR LIGHT (6) MODE button for the pedal set You can electronically swap the accelerator and clutch pedals. To do so, simply press the MODE button (6) for 2 seconds. The racing wheel’s internal memory stores whether the pedals have been swapped around or not. GAS AND CLUTCH PEDALS Colour of the MODE indicator light (6) NORMAL RED SWAPPED AROUND GREEN Other information regarding the MODE button To learn more about the MODE button and indicator light, please visit http://support.
T3PA – GT EDITION PEDAL SET 14/24
TECHNICAL FEATURES 1 Metal support for conical stop (not installed by default) 2 Conical stop 3 Attachment screw for metal support 4 2.
WARNING Before using this product, be sure to read these instructions carefully and save them for future reference. For safety reasons, never use the pedal set with bare feet or while wearing only socks on your feet. THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES. Warning – Pedal set pinching hazard during gaming sessions * * * * Keep the pedal set out of the reach of children.
AUTOMATIC CALIBRATION OF PEDALS IMPORTANT: - Never connect or disconnect the pedal set from the base of the wheel when the wheel is connected to the PS3™ or PS4™ system, or during gaming sessions, to avoid calibration problems. = Always connect the pedal set to the wheel before connecting the wheel to the PS3™ or PS4™ system. - Once the wheel has self-calibrated and the game has started, the pedals automatically calibrate themselves after being pressed a few times.
ADJUSTING THE PEDAL SET Each of the three pedals includes: - A metal head (8) with multiple perforations (nine for the accelerator – two for the brake – six for the clutch). - A plastic head support (7) (placed between the head and the arm) with four perforations. - A pedal arm (6) with two perforations. ATTENTION: To avoid any calibration problems, be sure to always disconnect your wheel’s USB cable from the PS3™ or PS4™ system before making any adjustments to your pedal set.
Adjusting the SPACING - Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and its support (7) in place. - Select your preferred position (to the left, centered, or to the right), then replace and re-tighten the screws so that the metal head (8) and its support (7) are held firmly in place.
Installing the conical stop (“CONICAL RUBBER BRAKE” mod) This modification (or “mod”) is not essential, and is not installed by default. This means that the brake pedal functions perfectly even if the mod is not installed. This mod lets you experience a different feeling and resistance when braking. It’s up to you whether or not to install it, depending on your own preferences. - Screw the conical stop (2) onto its metal support (1).
- Using the included 2.5 mm Allen key (4), attach the unit using the attachment screw (3) and the small central screw thread located on the underside of the pedal set.
CONSUMER WARRANTY INFORMATION Worldwide, Guillemot Corporation S.A., whose registered office is located at Place du Granier, B.P. 97143, 35571 Chantepie, France (hereinafter “Guillemot”) warrants to the consumer that this Thrustmaster product shall be free from defects in materials and workmanship, for a warranty period which corresponds to the time limit to bring an action for conformity with respect to this product.
Additional warranty provisions During the warranty period, Guillemot shall not provide, in principle, any spare parts, as Technical Support is the only party authorized to open and/or recondition any Thrustmaster product (with the exception of any reconditioning procedures which Technical Support may request that the consumer carry out, by way of written instructions – for example, due to the simplicity and the lack of confidentiality of the reconditioning process – and by providing the consumer with the re