User Manual

Manual of Sensor less Brushless Motor Speed Controller Thunder Power
3
Normal startup procedure:
Throttle range setting: (Throttle range should be reset when ever a new transmitter is being used)
Programming with throttle stick on transmitter (4 Steps):
1. Enter programming mode (see box below)
2. Select the programmable items (see box at right)
3. Set programmable item’s value (see box at lower left)
4. Exit programming (see box at lower right)
1. Enter programming mode
1) Switch on transmitter, move throttle stick to
top, connect the battery pack to ESC
2) Wait for 2 seconds, the motor should emit tone
like “beep-beep”
3) Wait for another 5 seconds, special tone like
“ ” should be emitted, this means the
programming mode is entered
4. Exit programming mode
There are 2 ways to exit
programming:
1. In step 3, after special
tone “ ”, please move
throttle stick to the bottom
position within 2 seconds.
2. In step 2, after tone
“beeeeeep-beeeeeep”
(i.e. item #8), move
throttle stick to bottom
within 3 seconds.
3. Set programmable item’s value:
Once an item is selected, you will again hear tones in loop. Set the value matching to a tone by
moving the throttle stick to the top when you hear the tone, then a special tone “ ” emits and
means the value is set and saved. (Keeping the stick at top, you will go back to step 2 and you
can select other items; Moving the throttle stick to bottom within 2 seconds will exit you from
the programming mode directly)
Tones
Items
“beep”
1 short tone
“beep-beep”
2 short tones
“beep-beep-beep
”
3 short tones
Brake Setting Disabled Enabled
Battery type Li-ion / Li-poly NiMh / Nicd
Cut off type Soft cutoff Hard cutoff
Cutoff voltage Low Medium High
Start mode Normal Soft Very-soft
Timing Low Medium High
2. Select the programmable items:
After entering programming mode, you will hear 8 tones in a loop in
the sequence listed in 1 - 8 below. If you move the throttle stick to
the bottom within 3 seconds after one kind of tone, then this item is
selected.
1. “beep” brake setting (1 short tone)
2. “beep-beep” battery type (2 short tone)
3. “beep-beep-beep” cut off type (3 short tone)
4. “beep-beep-beep-beep” cut off voltage (4 short tone)
5. “beeeeeep” sta rt mode (1 lo ng tone)
6. “beeeeeep-beep” timing (1 long 1 short)
7. “beeeeeep-beep-beep” set all to default (1 long 2 short)
8. “beeeeeep-beeeeeep” exit (2 long tone)
S w i t c h o n
t r a n s m i t t e r,
move throttle
stick to t op
Connect battery
pack to ESC,
a n d w a i t f o r
about 2 seconds
“ B e e p - b e e p ” t o n e
sho u ld be emi t ted,
means throttle range
highest point has been
correctly c onfirme d
Move throttle
stick to the
bottom, and
wait for about
1 second
“Beep” tone should be
emitted, means throttle
range lowest point has
been confirmed
ESC begins
t o p l a y
m u s i c ,
ready to fly
Move throttle
s t i c k t o
b o t t o m
,
s w i t c h o n
t r a n s m i t t e r
C o n n e c t ba t t e r y
p a c k t o E S C ,
special tone like
“ 1 2 3 ” m e a n s
power supply is OK
When self-test is
finished, a long
“beeeeeep” tone
should be emitted
ESC begins
t o p l a y
m u s i c ,
ready to fly
Several “beep-” tones
sho u ld be emi t ted,
presenting the value of
ea ch p rog ram item
Move throttle
stick upwards
to go fl yin g