User Manual

ManualsBrandsTii ManualsEquipment326 NIZ

TII P/N: 92202701

TII 320 NIZ / TII 126NIZ

TII 325 NIZ / TII 326NIZ

141 Rodeo Drive Station Protector With Network Interface

Edgewood NY 11717 Rev C 01/08

Customer Service/Sales 888-844-4720

INSTALLATION NOTE

GENERAL

a) This installation note covers the description and

installation of the TII 325 NIZ, 326 NIZ, 126 NIZ and

the 320 NIZ hereafter referred to as the unit. This

product is designed to combine a single pair TII 325,

326, 126, or 320 Station Protector with a single pair

Network Interface Device.

b) The unit is furnished complete with a mounting base,

an RJ-11 interface jack and plug, customer wiring

bridge , retaining nut, cover, and normally a protector

module / angle driver. The unit may also be furnished

with an optional ringer termination circuit.

1. WARRANTY

a) See TII Warranty. If this unit fails during the warranty

period, the factory should be requested to authorize

return. Return the unit prepaid. Units that fail due to

normal wear or abuse should be discarded.

2. DESCRIPTION

a) The unit is an adaptation of the TII 325, 326, and 320

series single pair Station Protector. The standard

cover of those products is replaced by a cover

assembly that isolates the telco wiring and station

protector from the customer. The RJ-11 plug and jack

are supplied with weather resistant grommets.

b) The cover assembly is held in place with a sturdy nylon

nut. The unit has a hinged, side opening cover,

complete with a provision for a security seal. Testing

instructions are provided inside the cover.

c) The product is furnished complete and requires no

special tools for installation.

3. INSTALLATION WITHOUT STATION ELECTRONICS

a) Remove the unit from the carton and inspect it

carefully for damage. If the unit is damaged, obtain

another.

b) Open the hinged door on the face of the unit and

unplug the modular plug from the jack (See Figure

1).

c) Remove the cover assembly from the base by

loosening the nylon cover nut and then pulling the

cover assembly away from the base (See Figure

1).

d) To mount the protector base, select the desired

hole pattern and knock out the plastic web over the

holes with a screwdriver. Position the base to the

mounting surface and attach it will appropriate

hardware.

e) Connect a proper station protector ground to the

molded-in ground stud using locally approved

grounding methods.

TII 320-71-NIZS

TII 325-1LM-NIZS

Summary of content (3 pages)

PAGE 1
TII 320 NIZ / TII 126NIZ TII 325 NIZ / TII 326NIZ 141 Rodeo Drive Edgewood NY 11717 Customer Service/Sales 888-844-4720 Station Protector With Network Interface Rev C 01/08 INSTALLATION NOTE TII 320-71-NIZS TII 325-1LM-NIZS GENERAL a) b) 1. The unit is furnished complete with a mounting base, an RJ-11 interface jack and plug, customer wiring bridge , retaining nut, cover, and normally a protector module / angle driver. The unit may also be furnished with an optional ringer termination circuit. 3.
PAGE 2
Figure 1 d) While holding the two Telco wires in place tighten Drive Screw to full down position. e) See 4.2.3 Final Installation Steps. 4.1 STATION PROTECTOR WIRING (If equipped with binding post protection) a) b) 4.2.3 Final Installation Steps Connect the drop wire to the Tip and Ring of the protector module, placing the wire under the bottom nut on each stud for station protector module (See Figure 2).
PAGE 3
5. TESTING a) When the installation of the unit has been completed, standard test procedures should be performed from the customer’s telephone to ensure that all connections are correct and that no grounds or short circuits are present.