Decking Installation & Maintenance Guide Installing TimberTech Decking..................................................................................... 2 Fastening Methods..................................................................................................... 4 TimberTech Solid Planks............................................................................................. 5 Trimming a TimberTech Deck......................................................................................
Installing TimberTech® Decking TimberTech Covers the Alternative Decking and Railing Market Tools Required TimberTech planks can be installed with a minimum number of readily available tools. However, many other tools are available that can provide even greater efficiency and ease of installation. All tools should be used per applicable manufacturers’ instructions. Some of the basic tool requirements: To get information on other TimberTech products, visit timbertech.
Installing TimberTech® Decking Extreme Heat Warning Calculating Material Requirements Be aware of excessive heat on the surface of TimberTech products from external sources, such as but not limited to, fire or reflection of sunlight from energy-efficient window products. Low-emissivity (Low-E) glass can potentially harm TimberTech products. Low-E glass is designed to prevent passive heat gain within a structure and can cause unusual heat build-up on exterior surfaces.
Fastening Methods 12" TimberTech Fascia Boards Using screws with proper installation of TimberTech Fascia provides the best long-term holding. TimberTech recommends the use of TimberTech TOPLoc Fascia Fasteners for best results. Refer to gapping requirements on page 3 for proper installation. • Set fascia in place being sure to follow proper gapping requirements. • Drive TOPLoc fascia fastener 90 degrees with the fascia surface so that the screw head is flush with the surface.
TimberTech Solid Planks Earthwood Evolutions®, Twin Finish®, Reliaboard®, and Docksider® Standard Joist Spacing Important Information TwinFinish To get information on other TimberTech products, visit timbertech.com or ask your dealer for these installation guides: • TimberTech planks are intended to be installed embossed side up. The unembossed surface is not to be used as a walking surface. This applies to all decking surfaces.
TimberTech Solid Planks/ Trimming a TimberTech Deck Earthwood Evolutions®, Twin Finish®, Reliaboard®, and Docksider® Stair Installation TwinFinish, ReliaBoard, DockSider, Earthwood Evolutions, and TwinRiser Boards: TimberTech does not recommend installing planks on steps without a riser board. • Stairs should be constructed per local code requirements. • Ensure the stringer step is at least the depth of two full planks plus a 1/8” to 3/16” gap between planks. • For gapping requirements, see page 3.
CONCEALoc® Hidden Fastener Important Information CONCEALoc Hidden Fasteners were designed exclusively to install TimberTech grooved and square shouldered planks. IMPORTANT! Read all instructions carefully and completely to ensure proper installation. • In areas with obstructed airflow such as roofs and on-grade applications, a minimum of 1-1/2” is required. • Sleeper system must be supported by and connected to the substructure over which the deck is built.
CONCEALoc® Hidden Fastener 3 INSTALL CONCEALoc FASTENERS • Install provided screw at 45° angle through the fastener and into the joist while applying pressure on the fastener. • Install one fastener and screw at each joist. • Make sure fastener is in full contact with edge of plank and the screw is holding the fastener down tight to the deck board. 4 COMPLETE INSTALLATION • Place the next plank into position against the fasteners.
CONCEALoc® Hidden Fastener 6 HOW TO: INSTALL ON DIAGONAL • When the deck is located in a corner of the house, start with small triangular piece of decking in the corner and work your way out. • Offset the center 1/2” towards the long point of the joist, so screw will not exit the side of the joist when driven. 7 Incorrect Correct: Shift over 1/2” HOW TO: REPLACE A PLANK • Make two parallel cuts down the center of the board to be replaced, then remove the center piece.
Cortex® Hidden Fastening System Cortex® Hidden Fastening System Installation Instructions Suggested Drills Impact Drivers are not recommended when using TimberTech Cortex. Corded or cordless (18V battery) drill with 1/2” chuck. 1 DRIVE SCREW • Using Setting Tool provided, drive screw at medium or high speed until it disengages at the proper level below the deck surface. • Drive at one continuous speed, do not slow down.
Cortex® Hidden Fastening System Important Information Restricted Cortex Uses • The Cortex Setting Tool must be used to set the Cortex screw to the proper depth. • The Cortex fastener must be driven perpendicular to the deck surface for proper fit and ideal finished look. • The cored hole must be free of debris or moisture. Use a smooth hammer head to set the Cortex plug. • The interaction between the deck board, screw, and plug is essential.
Care and Cleaning With proper installation and care, TimberTech products will provide years of outdoor living pleasure. For most current recommendations, visit http://www.timbertech.com/warranty-and-care/care-and-cleaning/default.aspx Storage To clean Earthwood Evolutions we recommend the following methods: *Keeping an unsoiled deck surface will make cleanup after a spill much easier. Store TimberTech products under cover to maintain a clean surface.
Care and Cleaning Spot Stains Many stains can be cleaned with soap and water. If the stains have set, the following cleaners have been found to remove or reduce the stains. Always follow the manufacturer’s instructions to achieve maximum results. Areas cleaned may lighten; this will require 8-10 weeks exposure to the sun to match the remaining product. Dirt, Grime, Tannin and Mildew Stains TimberTech products are formulated to inhibit mildew growth and minimize staining.
Notes Page 14
Notes Page 15
Decking Installation & Maintenance Guide CPG Building Products, LLC 894 Prairie Avenue Wilmington, OH 45177 timbertech.com 1.800.307.