Presence detector PresenceLight 180 PresenceLight 360 Art. Nr. 200 0 050 D Bedienungsanleitung 2 F Notice d´utilisation 22 GB Installation manual 42 E Manual de instrucciones 62 I Istruzioni per l'uso NL 82 Gebruikershandleiding 102 1103020206 © 08.08 Theben HTS Art. Nr.
English Installation manual Presence detector PresenceLight 180 PresenceLight 360 Table of contents 1. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 2. Function and performance characteristics. . . . . . . . . . . . . . . . . . . . . . . 44 3. Location / Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 4. Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GB Thank you for choosing a Theben HTS presence detector and putting your trust in us. 1.
2. Function and performance characteristics The presence detectors PresenceLight 360 and PresenceLight 180 detect persons within a room on account of slightest movements. Simultaneously, their light sensor measures the brightness in the room and compares it to the pre-set brightness threshold. PresenceLight 360 is the presence detector of choice for use in small rooms, corridors and wet zones. PresenceLight 180 is the presence detector of choice for use in corridors, transit zones and wet zones.
3. Location / Installation 3.1 Detection Range PresenceLight 360 GB The ideal mounting height is 2,0 - 3,0m. The sensitivity of the detector decreases with increasing mounting height. In order to ensure proper detection of persons, the PresenceLight 360 requires an unobstructed “view” of the persons. Office equipment, plants, suspended lamps etc. may affect the presence detection (shading).
PresenceLight 360: PresenceLight 180: 3 3 2,2 m 2 2 1 1 o Lux 0.8 0 0 o 0 m 3.5 3 2 1 0 1 2 3 3.
3.3 Connection The presence detector must be flush mounted into a concealed housing. The enclosed set of seals is to be used for IP54 installation. A suitable frame for surface mounting is also available. If the surface-mounting seal set is used for surface mounting, the detector will also comply with Protection Class IP54. L N GB L N PresenceLight A 3.
4. Start-up The detectors are supplied ready for operation with a factory setting of recommended standard values. The QuickSet plus service remote control for starting-up the system is optionally available. With the remote control all potentiometer values can be set from a distance. 4.
Depending on the installation location, natural light intensity, furniture, reflection characteristics of the room and the furniture it may be necessary to correct the settings by 1-2 steps on the scale. For ease of setting up, we recommend the service remote control QuickSet plus. GB Switch-off time delay ● Transfer zones approx. 5min. ● Working areas approx. 10min. ● In the range between 2 - 15min the switch-off delay time varies according to its self-learning behavior.
4.3 Behaviour on switching on Whenever the unit is energised, the detector goes through 3 phases. 1. Start-up phase (30sec) ● LED flashes every second, switching contact is closed (light on) ● In case of absence, the contact opens after 30sec. 2. Service phase (10min) ● The “Light” contact reacts instantaneously on brightness in order to check the brightness threshold.
. Additional wiring examples .1 Parallel circuit operation of multiple detectors ● Directly connect the switching contacts of multiple detectors in parallel. GB L N ● Set the brightness threshold and the switch-off delay time on all detectors. L N PresenceLight ● The total permissible load does not increase. A L N PresenceLight A .2 Parallel circuit operation with external staircase lighting timer ● Directly connect the switching contacts of multiple detectors in parallel.
6. Test mode The test mode serves to check the presence detection and the wiring. 6.1 Setting the test mode with potentiometer ● Set potentiometer «min.» to «test». 1. Start-up phase (30sec) ● The switching contact is closed for 30sec. ( LED 20s «on», 10s «off» ). 2. Test mode ● In case of movement (LED on), the contact closes. ● In case of absence (LED off), contact opens after 10sec. ● The detectors remain permanently in the test mode. Please note: brightness measurement inactive in test mode. 6.
7. Technical specifications Presence Detector Detection range PresenceLight 360 horizontal vertical Recommended mounting height 2.0m - 3m Maximum range 6 x 6m (Mh 2.5m) 8 x 8m (Mh 3.5m) Mixed light measurement Light measurement deactivated ca. 10 - 1500Lux „on“ Switch-off delay time for light Short pulse 10s - 20min. 0.5s „on“ / 10s „off“ Presence Detector Detection range GB 360º 120º PresenceLight 180 horizontal 180º Recommended mounting height approx. 1.6m - 2.
PresenceLight 360, PresenceLight 180 Switching contact 230V ± 10%, 50Hz In-line fuse max. 10A Max. switching capacity incandescent lamps, halogen Max. nr. of electronic ballasts *) (A relay or contactor must be connected in case of more powerful devices) 1400VA 1200W 5x 10x 16x 16x (1x80W) (1x58W); 5x(2x58W) (1x36W); 8x(2x36W) ( < 36W) Mounting Mounting depth Mounting diameter Mounting plate (integrated) 40mm 50mm 70x70mm Screw Terminals max. 2 x 2.
*) Use of T5-FL: When using T5-FL lamps with a comparable wattage, the same number of electronic ballasts may be connected to the detector’s switching contact as for the T8-FL. When using the 80W-FL, the number should be halved in comparison to the 58W-FL. 8. Warranty declaration Theben HTS presence detectors are manufactured and quality-tested with the utmost care using state-of-the-art technologies. Theben HTS therefore guarantees perfect function, provided the detectors are used as intended.
Returns In the event of a warranty claim please send the unit together with the delivery note and a brief description of the fault to the dealer concerned. Industrial property rights The concept including hardware and software of these units is protected by copyright. .
Dimensions PresenceLight 360 86 27 GB 40,5 40 70 56 60 48 4 11 45.
Dimensions PresenceLight 180 36 48 86 70 60 32 4 11 8 56 40 40,5
Dimensions surface frame for PresenceLight 360, PresenceLight 180 70 84 57 GB 8 17,7 86 24 24 4,5 22,7 Declaration of CE conformity This device complies with the protection regulations of the EMC directive 2004/108/EC and of the Low Voltage directive 2006/95/EC. Subject to change without prior notice. Errors and omissions excepted.
Theben AG Hohenbergstrasse 32, DE-72401 Haigerloch Tel. +49 (0) 74 74 692 - 0 Fax +49 (0) 74 74 692 - 150 Hotline Tel. +49 (0) 74 74 692 - 369 Fax +49 (0) 74 74 692 - 207 hotline@theben.de Switzerland Theben HTS AG Im Langhag 11, CH - 8307 Effretikon Tel. +41 (0)52 355 17 00 Fax +41 (0)52 355 17 01 www.theben-hts.ch Die Kontaktadressen für weitere Länder finden Sie auf www.theben.de Veuillez compulser les adresses pour des pays supplémentaires sur www.theben.