Cat No. fst11a – 24 Hour Cat No.
1.
2. Battery The unit has an in-built non-replaceable, rechargeable battery, which will keep the programmed times during power down situations for up to 4 weeks. If the screen goes blank, once power is restored and 4 hours elapsed (to give a working battery charge) reset must be pressed, and times/programmes re-entered. Switched live terminal (load live connection) 230 V~ 13A T40 Supply live terminal Supply neutral terminal Switched neutral terminal (load neutral connection) Fig.
. Installation The unit is designed to replace an existing single gang connection unit or fixed appliance outlet giving timed mains output, protected by a BS 1362 fuse. The unit is capable of forming part of a ring main (the terminals can accept 2 x 2.5mm sq. cables) or terminating a spur off the ring main. The unit requires a minimum depth of 25mm within the box. Ensure that the wiring is adequate for the load to be carried. Connect incoming and outgoing cables to the relevant terminals.
7. Setting the Date and Time of Day 7.1 Initially Setting the Date and Time of Day Press the ‘Time’ button and hold for approx. 2 seconds. Whilst holding, the word ‘hold’ will show bottom left in the display. After 2 seconds, there will be the option of automatic daylight saving (summer/ winter time). Press ‘Adv’ or ‘Bst’ to change from yes to no. Adv Adv SET SET Prog Prog Bst Bst Prog Prog Adv Adv SET SET Time Time Prog Time Time Time Then press ‘Time’, the default year 2009 will be displayed.
Press the ‘Time’ button and the day digits will flash:– Day Day Month SET SET Time Prog Time Prog Time Day Prog Press the ‘Time’ button and the hour digits will flash:– SET SET Time Day Time Time Prog Prog Time Time Time Time Time Time Prog Prog Time Use ’Adv’ or ‘Bst’ to set the hour (24 hour clock). SETSET Time Prog Time Prog SETSET Use ‘Adv’ or ‘Bst’ to set the day.
Day SET SET Prog 7.2 ModifyingProg the Date and Time of DayAdv Normally the only change required will be to the time of day minutes, in which case press and hold ‘Time’Time for 2 seconds, during which the word ‘HOLD’ Bst will appear in theTime bottom left hand corner of the display. Press ‘Time’ repeatedly until the minutes are shown flashing then use ‘Adv’ or ‘Bst’ to make the change. Time Prog Prog Finally press ‘Time’ briefly to get back to operating mode.
Adv Prog Adv Prog Bst Time SET ON Bst Mo Tu We Th Fr (Example shown is for a 5 + 2 day program, as the display shows Mo Tu We Th Fr). SET Adv Prog Adv Use ‘Adv’ or ‘Bst’ toProg set the hours Prog and then ‘Prog’ to change between hours and Adv Adv ON Time Time Adv Adv Adv Prog Prog Prog Bst BstBst Time Time Time OFF SET minutes. Followed by ‘Adv’Prog or ‘Bst’ again to set the minutes. Bst Bst Bst Bst Mo Tu We Th Fr Press ‘Prog’ to change to program OFF Mo Tu Wetime.
Adv Prog SET Prog 8.2 Programming across midnight: SET Time Bst The display will show the correct day and time but the ON/OFF indicator may not reflectTime the current programme accurately in which case press the ‘Adv’ button to correct the indicator. In the same way as for individual programmes, days or groups of days can be omitted either by leaving dashes in all the locations forTime a day or a group of days or by leaving the programming Progwhere all further entries are to be dashes.
Prog Adv SET SET Prog Prog Adv – Programming the ON/OFF Times ON Prog ON FST11A only Time Bst Bst Adv Prog Adv Mo Tu We Th Fr BstThe FST11A is similarTime Bst mode to the Prog FST17A but only has one day group SET ON Mo Tu We Th Fr in programming – Mo Tu We Th Fr Sa Su giving 24 hour operation. SET SET BstUp to 4 programmesTime Bst same way can be entered (once only required) in the Mo Tu We Th Fr Advas for the FST17A (refer Progto section 8). Adv Prog Adv Prog Adv Prog OFF 10.
. Specifications This product complies with: LVD Directive 72/23/EEC. EMC Directive 89/336/EEC. and relevant clauses of the following standards: BS EN 60730-7-2:1992; Particular requirements. Timers and time switches. BS1363-4:1995; Specification for 13A fused connection units. EN61000-6-3:2001; Emission Requirements for the RCLI Environment. EN61000-6-1:2001; Immunity Requirements for the RCLI Environment. Permissible loads: 13A resistive. 5A filament lamps. 1hp motor.
5 Year Guarantee In the unlikely event of this product becoming faulty due to defective material or manufacture, within 5 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For years 2 to 5 or any difficulty in the first year telephone our helpline on 020 8450 0515. For assistance with the product please contact:– HELPLINE 020-8450-0515 or email helpline@timeguard.