T128 IB Dec 10,12 151mmw x 151mm H Color: Black Model T128 Dual Alarm Clock with USB Charging & Night Light For additional information, online registration, and exclusive special offers please visit our website:
Introduction Thank you for selecting this Timex Model T128 Dual Alarm Clock with USB Charging.
FCC Information This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Controls and Indicators Top Panel Time / Alarm Set Forward Button Alarm 2 Button Time / Alarm Set Back Button NITELITE Button Alarm 1 Button NAP (Alarm Reset) Button Snooze Button (Display Dimmer Control) Back Panel Back-up Battery Compartment Pin Hole To Release Battery Door Charging Mode Selector (A / B) OPEN Time Set Button AC Adapter Jack RESET button (behind back panel) USB Charging Port Alarm Volume Selector (LOUD / SOFT) DST(Daylight Saving Time) Switch (OFF/ON) 1
Front Panel Time Display ALM 1 (Alarm 1) Indicator PM Indicator ALM 2 (Alarm 2) Indicator BATT LOW (Low Back-up Battery Warning Indicator) Activating the Backup Batteries TEST T EST 2 RESET E R SET • Remove the alarm clock and the AC power adapter from the carton. Remove all packing material from the alarm clock. The carton is recyclable. • The CR2032 lithium back up battery has been pre-installed in the battery compartment on the back panel.
OPERATING INSTRUCTIONS Adjusting For Daylight Saving Time (DST) If you are currently observing Daylight Saving Time, set the DST switch on the back panel to the ‘On’ position. If you are currently observing Standard Time, set the DST switch on the back panel to the ‘Off’ position. Setting The Time When the clock is connected to the AC outlet for the first time the display will show “12:00” and the PM indicator will be ‘On’, indicating that the time displayed is 12:00 noon.
OPERATING INSTRUCTIONS Reviewing The Wake Up Times To review the current wake up time settings, press the ALM 1 or ALM 2 button once. The display will change from current time to wake-up time for 5 seconds and the selected ALM 1 or ALM 2 indicator will flash. After 5 seconds the display changes back to current time.
OPERATING INSTRUCTIONS Nap Timer The Nap Timer allows you to set a 3rd alarm to wake you after a nap of up to 90 minutes without disturbing your regular alarm settings. The Nap timer settings are 5, 10, 15, 20, 30, 45, 60, 90 minutes and OFF The default Nap Timer setting is 5 minutes. To adjust the amount of nap time: • Press the NAP button to activate the Nap Timer mode. The nap time display begins flashing.
CARE AND MAINTENANCE Replacing The Back Up Battery The CR2032 back up battery that was supplied with your Timex alarm clock should provide adequate back up power for up to 3 years or even longer, depending on the frequency and duration of power outages in your home. When it is time to change the battery the BATT LOW indicator begins flashing in the lower right corner of the display. When you see the flashing indicator you should purchase a new CR2032 battery as soon as practical.
A Consumer Guide to Product Safety IMPORTANT SAFETY INSTRUCTIONS This unit has been designed and manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire hazards. Please read all the safety and operating instructions carefully before installation and use. Keep these instructions handy for future reference. Take special note, adhere to all warning, and always follow the instructions on the unit and in the instruction and service manuals. 1.
Limited 90-Day Warranty Information Timex Audio Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase. Should service be required by reason of any defect or malfunction during the warranty period, SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $5.
T128-121012-A Printed in China
