User's Manual

ManualsBrandsTippmann ManualsGame98 Custom

❏

Carefully install the left receiver half (make sure halves fit

flush).

❏

Place battery connector through left receiver half

❏

make sure

the magnet fits into left receiver half slot so it does not break and

❏

wires are not pinched as you

❏

place left half on right half so

the halves fit flush.

❏

Insert 5 short receiver bolts .

❏

Insert front grip and

❏

insert

long receiver bolt

to hold grip. For ease of installation tighten

the bolt

over the trigger first, then tighten 5 remaining bolts / .

❏

Attach adapter with 2 bolts (NOTE: on 98 Custom

markers short adapter bolt goes in front).

❏

Install barrel .

❏

Attach 9v battery to battery connector

and be sure wires lay flat inside the cutout

area of receiver.

❏

Carefully tilt and insert battery

(wire attached end first

) into receiver.

❏

Install left receiver grip with 2 bolts .

WARRANTY AND REPAIR POLICY

WARRANTY OR REPAIR PROCEDURE

If you should encounter any problems with your marker and you

have aftermarket parts on your marker, please test it with the

original stock parts before sending it in.

Always unload and remove air supply before shipping a marker (see

page 21). Do not ship your air supply tank if it is not completely empty.

For warranty and non-warranty repair:

1. Ship or deliver your product(s) to:

Tippmann Sports, LLC

2955 Adams Center Road

Fort Wayne, IN 46803

2. Postage or delivery charges must be prepaid.

3. Include a brief statement regarding the requested repair,

your name, return address and telephone number where

you can be reached during normal business hours, if possible.

Our policy is to complete the necessary repair work within 24 hours

and return it to you via regular ground UPS. If you wish to have it

returned using a faster service, you can request for NEXT DAY

AIR UPS OR SECOND DAY AIR UPS. You will be charged for this

service and must include your credit card number with the

expiration date. Your card will be charged the difference in

additional cost over regular ground shipping service.

Tippmann Sports, LLC warrants that this product is found free from

defects in materials and workmanship for a period of 2 years

from the original date of purchase by the initial owner/purchaser.

This warranty does not apply to defects discovered after purchase

which were caused by the unauthorized modifications and

alterations of our product. Tippmann Sports, LLC will repair or

replace, without charge, any of its markers that have failed

through defect in material or workmanship. Tippmann

dedicated to providing you with the ultimate paintball marker

and the quality support necessary for satisfactory play.

WARRANTY REGISTRATION

1. On line at www.tippmann.com.

2. Complete attached registration card and mail to the above

address.

Storage

Before storage unload and remove air supply (see page 21). Then

install Barrel Sleeve (see page 2) and put your marker in Safe

Mode (see page 4). You should store your marker in a dry area.

Before storing your marker make sure that the marker is cleaned

and oiled (see cleaning and maintenance on page 21) so that it

does not rust. Store your marker with the bolt in the forward

position, uncocked.

When removing your marker out of storage make sure Barrel

Sleeve is installed (see page 2) and safety is in Safe Mode (see

page 4). You should re-oil the rear bolt and the front bolt o-ring

before use (see cleaning and maintenance on page 21).

Repairing Air Supply Cylinder Leaks

The most common leak occurs from a bad air supply valve o-ring. To

replace a valve o-ring you must first remove the bad o-ring and then

install a new one. This o-ring is located on the tip of your air supply

valve. The best valve o-rings are made of urethane. The urethane o-rings

are not affected by high air supply pressures. These may be purchased

from Tippmann

or your local paintball dealer.

NOTE: If new valve o-ring does not resolve air supply leak, do not

attempt to repair air supply cylinder. Contact Tippmann Sports, LLC

or your local paintball dealer.

E-Trigger

Reassembly (continued from page 23)