Instructions / Assembly

English
© Titan Tool Inc. All rights reserved. 7
Painting
1. Place a ve gallon bucket of material between the bucket
holders on the cart. Make sure the bucket holders hold
the ve gallon bucket securely. Adjust the bucket holders
using the thumb screw located underneath each holder, if
necessary.
NOTE: Whenusingthislinestriperforrsttime,itmay
be helpful to use water in place of paint to gain
familiarity with the operation of the line striper.
After changing from water to paint, test spray
severallinesoncardboard,roongfelt,orrosin
paper before striping to ensure correct line width.
2. Place the siphon tube into the bucket of material.
3. Place the return hose into a metal waste container.
SPRAY
PRIME
4. Turn the PRIME/SPRAY knob to the
PRIME position.
5. Fully depress the pusher stem to make
sure the inlet ball is free.
6. Turn the DirectLink pressure control knob
fully clockwise to minimum.
Clockwise
7. Start the engine:
Prime
bulb
Starter
rope
Choke
lever
a. Move the choke lever up to
the full choke position.
b. Push the rubber prime button
7-10 times.
c. Pull the starter rope rapidly
and rmly. Continue to hold
the rope as you let it return.
Pull and return the rope until
the engine starts.
d. Once the engine is running,
slowly move the choke lever
down to the closed position.
8. Slowly turn the DirectLink pressure control knob
counterclockwise to increase the pressure until uid starts
to come out of the return hose. Use only enough pressure
to keep the uid coming out.
9. Allow the sprayer to run for 15–30 seconds to ush the
test uid out through the return hose and into the waste
container.
10. Turn the DirectLink pressure control knob fully clockwise
to minimum.
11. Turn off the sprayer by pressing and holding the engine
shutoff switch until the motor shuts off.
12. Remove the return hose from the waste container and
place it in its operating position above the bucket of
material.
13. Start the engine.
SPRAY
PRIME
14. Turn the PRIME/SPRAY knob to the
SPRAY position.
15. Unlock the gun by turning the gun trigger
lock to the unlocked position.
16. Turn the DirectLink pressure control knob
slowly counterclockwise to increase the
pressure.
17. Fully pull the spray lever on the cart handle. Fluid will
begin owing through the spray hose and out of the gun.
18. Continue to pull the spray lever on the cart handle until
material is coming out of the gun.
19. Release the spray lever.
20. Lock the gun by turning the gun trigger lock to the locked
position. If necessary, loosen the gun holder clamp knob
and then engage the spray gun trigger lock. Move the
spray gun to its original position and tighten the clamp
knob.
21. Turn the DirectLink pressure control knob fully clockwise
to minimum.
22. Turn the PRIME/SPRAY knob to PRIME.
23. Turn off the sprayer by pressing and holding the engine
shutoff switch until the motor shuts off.
24. Attach tip guard and tip to the spray gun. Refer to the
instructions later in this section.
POSSIBLE INJECTION HAZARD. Do not spray
without the tip guard in place. Never trigger the
gun unless the tip is in either the spray or the
unclog position. Always engage the gun trigger
lock before removing, replacing or cleaning tip.
25. Start the engine.
26. Turn the PRIME/SPRAY knob to SPRAY.
27. Fully pull the spray lever on the cart handle to trigger the
spray gun. Test the spray pattern and line position on a
long piece of roong felt or cardboard. Check for proper
line width and position. If adjustment to the position of
the spray gun is required, refer to the “Setup” procedure
earlier in this section.
28. Make sure that the spray gun shuts off completely when
the gun trigger is released. If adjustment to the trigger
tension is required, refer to the “Adjusting the Trigger
Tension” procedure in the Maintenance section of this
manual.
29. Begin striping.
a. Position the line striper slightly in front of the striping
path.
b. Start walking with the line striper and trigger the gun at
the beginning of the striping path.
c. At the end of striping path, release the trigger and
continue walking a short distance, if possible.
NOTE: Triggering the gun after the line striper is moving
and releasing the trigger before the line striper
stops produces an evenly painted line from start
tonish.Ifthestripingpathendsatanobstacle,
release the trigger at the same moment that the
line striper stops moving.
Attaching the Tip Guard and Tip
Tip seal
retainer
Tip seal
Tip
Tip
handle
Tip
guard
Use the following procedure to
install the tip guard and tip to the
spray gun.
1. Perform the “Pressure Relief
Procedure” described in this
manual.
2. Using the arrow head on the
tip handle, insert the tip seal
and tip seal retainer into the
back of the tip guard. Press
in for nal adjustment.
3. Insert the tip into the slot on
the tip guard.
4. Thread the tip guard onto the
gun. Position the tip guard in
the desired spraying position
and tighten securely.
NOTE: The arrow on the tip
handle should be
pointing in the forward
direction for spraying.