Installation Guide

10
Using a box knife, cut template to shape of moulding and trim revealed by the markings. Test t the template. (It should lay across the bottom bar, with the front
edge ush to the front edge of the bottom bar, and t in and around the corners of the existing moulding and trim.)
Once you have created a good template, use the template to mark the threshold plate.
Using tin snips/aviator snips, cut threshold plate to match the shape of the template (6). Position threshold plate to extend across the bottom bar and into the
existing threshold. Use 1/8" drill bit to pre-drill holes for mounting screws. Attach threshold plate to existing threshold using the provided screws (L).
4
5
6
Existing door contour Make cardboard template Fit template to contour Cut template to contour Mark threshold plate Cut threshold plate to t
1 2 3 4 5 6
Installing the Door
9
Hang the security door (B) on the jamb hinges (A),
holding the door open at more than a 90° angle
(see diagram below), starting with the bottom pin rst.
More than 90°
Top View
A
B
Jamb side (A) hinge
Door side (B) hinge
Leveling Washers
Installing the Bug Sweep
Open the door. Slip the multi-blade bug sweep (G) onto the bottom of the door. Hold sweep in place and close the door.
Allow the sweep to fall and sit resting on the threshold plate (F). Note: Be sure there is not a gap between the sweep and the
threshold plate and that the sweep is centered on the bottom of the door. Use a 1/8" drill bit to pre-drill the two outer holes
for mounting screws. Using the screws provided (L), attach the sweep to the bottom of the door through the two outer holes.
Test that the door opens and closes freely. If not, loosen the screws and make necessary adjustments. Retighten screws and
test again. Repeat until successful. Pre-drill remaining holes and install the rest of the provided screws (L).
11
Installing the Door Closer and Wind Chain (Optional, Purchased Separately)
Follow the manufacturer’s instructions included with the wind chain and door closer to install on your new security door.
Note: It is not required to use a wind chain and door closer for your security door.
12
Final touch-up and upkeep suggestions
Page 4
Caulk (not included)
Caulk around the outside
of the security door jamb
frame, using paintable
caulk, and paint to the
desired color.
Paintable caulk & gun
Touch-Up Paint
Shake the supplied touch-up paint (H)
vigorously for 2 minutes and paint the
heads of the one-way screws as indicated
in the diagram.
White Grease Lubricant (not
included)
Use white grease to lubricate the hinges of
your new security door every six months.
2
3
(H)
Continued
8
Warranty Information
Your Titan Premium Security Screen door is warranted for residential installations against manufacturer defects under normal use for as long as you own your Titan product, and terminates if you
sell or otherwise transfer the product or the property upon which it was installed. The Powder Coat Finish is warranted for ve years from date of purchase. All other components of the product,
including sunscreen material, bug sweeps, weather-stripping, and composite materials are covered for one year from date of purchase. If the door breaks or structural defects occur, Titan will, at our
discretion, repair or replace the door. If your home is burglarized and entry was accomplished through a Titan security door, locked with a double dead bolt, Titan will pay your insurance deductible
up to $1000 or replace as applicable the damaged Titan security door at no charge (the "Home Protection Warranty"). Replacement items may vary in style due to changes in suppliers and product.
Not all colors can be reproduced if colors have been discontinued. Titan is not responsible for any labor expense required to repair or replace the door. Titan is not responsible for securing the
property while warranted items are being repaired or replaced. Cutting parts not specied by the installation guide or parts drilled incorrectly are not included in this warranty. Any problem caused by
abuse, misuse, failure to maintain warranted item properly, adjustments due to settling of the structure that the product is mounted on, or acts of God, are not covered.
To make a claim under this Warranty, send a brief written description of the problem, a picture of the claim, proof of purchase,
and your contact information to: Titan Security Doors, 973 N. Colorado Street, Gilbert AZ. 85233 Attn: Warranty Claims
VIEW INSTALLATION VIDEOS
AND LATEST INFORMATION AT